JBL 4365 Manuel utilisateur

OWNER’S MANUAL

JBL®STUDIO MONITOR

MODEL 4365

3-way loudspeaker

43654365

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 1 17/06/10 10:23:46

INTRODUCTION

THANK YOU for purchasing the JBL®studio monitor model 4365. The 4365 is a new member of the family of JBL

large studio-monitor speakers that dates back to 1963 with the original model 4320 studio monitor. By incorporating

technology first developed for the Project K2S9900 with new Bi-Radial®horns, the 4365 fuses innovation with JBL

tradition. To get the best performance from your new studio monitor, please read these instructions thoroughly.¨

PaCkage CONTeNTs

EACH JBL 4365 BOX CONTAINS:

One (1) JBL 4365 studio-monitor speaker•

Four (4) spiked foot inserts•

Four (4) metal coasters for use on tile, wood and linoleum floors•

If you suspect that there has been shipping damage, report it immediately to your dealer. We recommend that you

keep the box and packing materials for future use.

UNPaCkINg The sPeakeR

CAUTION: The 4365 weighs 86.4kg (190 lb). To avoid personal injury or damage to ﬂoors or the

speaker, we strongly recommend that at least two people unpack and move the speaker.

The speaker has rounded, stainless-steel feet installed on the bottom of its cabinet. To avoid damage to your floor,

we strongly advise that you unpack the speaker on a well-protected surface, such as a thick carpet or a thick piece of

cardboard.

TO UNPACK THE SPEAKER:

Carefully cut the tape on the carton’s front flap. Note: Only three of the flap’s four edges have tape.1.

Open the flaps and remove the side filler sleeves by pulling them straight out of the carton.2.

Stand on the box’s lower flap and gently rock the speaker and its packing back and3.

forth while pulling it out of the carton. In this way you can “walk” the speaker out of the

carton. It helps to have a second person hold the carton steady from the back side.

Once the speaker is out of the carton, remove the upper and middle pads. The speaker’s accessories are packed4.

on the top end of the upper pad, so be careful not to discard them.

Remove the cloth bag covering the speaker.5.

With another person’s help, carefully tilt the speaker on its side onto a thickly carpeted or well-padded surface and6.

remove the bottom pad. Then tilt the speaker back up on its feet.

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 2 17/06/10 10:23:46

www.jbl.com

English

ChaNgINg The sPeakeR’s FeeT

The 4365 is shipped with rounded feet attached to the bottom of its cabinet.

TO CHANGE TO THE INCLUDED SPIKED INSERTS:

Turn the speaker upside down onto a thickly carpeted or well-padded surface.1.

Unscrew and remove the rounded inserts of the installed feet. If the inserts are difficult to loosen, use an 18mm2.

(11/16-inch) wrench.

Screw the spiked inserts into the feet.3.

A. Remove Rounded Foot Insert B. Replace with Pointed Foot Insert

IMPORTANT: To prevent damage (scratches, indentations, etc.) to wood or linoleum floors due to the weight of these

speakers, always use the included coasters. Be especially sure to use the coasters on tile surfaces to prevent cracking

the tile.

PLaCeMeNT

Before deciding where to place your speakers, note that the floor at your selected location must be capable of

supporting a load of 86.4kg (190 lb). Because the stainless-steel feet solidly couple the speaker to the floor, a flat, hard

surface such as wood or linoleum is preferable. However, the coupling system, along with the speakers’ substantial

weight, should result in excellent performance on any surface, even carpeting.

To decide on a final location for your speakers, survey your room and think about placement using the illustration

below as a guide.

Listening Position

40° – 60°

>50cm

(20 in)

>50cm

(20 in)

For best results, place the speakers about two to three meters (about six to ten feet) apart. If you place the speakers

farther apart, angle them toward the listening position.

The speakers will produce the most accurate stereo soundstage when the angle between the listener and the speakers

is between 40 and 60 degrees.

Position each speaker so that its tweeter is approximately at ear level.

Generally, bass output will increase as the speaker is moved closer to a wall or corner. For best performance, we

recommend that you place the speakers at least 50cm (about 20 inches) away from the side walls.

NOTES ABOUT SPEAKER PLACEMENT:

To prevent damage (scratches, indentations, etc.) to wood or linoleum floors due to the weight of these speakers,•

always use the included coasters. Be especially sure to use the coasters on tile surfaces to prevent cracking the

tile.

Avoid placing the speakers near power ampliﬁers, heat registers or other objects that generate large amounts of•

heat.

Do not place the speakers in very humid or dusty places.•

Do not place the speakers in direct sunlight or in places where they will be exposed to other strong light.•

The 4365 is not video-shielded and may distort or discolor the picture if placed close to some types of TVs.•

If the speakers do distort or discolor your TV’s picture, move the speakers away from the TV until the distortionor•

discoloration disappears.

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 3 17/06/10 10:23:47

CONNeCTIONs

CAUTION: Make sure that all of the system’s electrical components are turned OFF (and preferably

unplugged from their AC outlets) before making any connections.

Speakers and amplifiers have corresponding positive and negative (“+” and “–”) connection terminals. The 4365 has

two sets of connection terminals; jumper wires connect the terminals to each other. The terminals are marked “+” and

“–”. Additionally, the “+” terminals have red rings, while the “–” terminals have black rings. See the illustration below.

We have designed the 4365 so that a positive voltage at the “+” (red) terminal will cause the speaker transducers to

move outward (toward the room).

We recommend using a high-quality speaker wire with polarity coding. The side of the wire with a ridge or other coding

is usually considered positive polarity (“+”).

To ensure proper polarity, connect the left- and right-channel “+” terminals on the back of the amplifier or receiver to

their respective “+” (red) terminals on the speakers. Connect the “–” (black) terminals in a similar way. See the owner’s

manual of your receiver or amplifier to confirm its connection procedures.

BASIC SINGLE-WIRE CONNECTION:

Connect the amplifier to each speaker as shown in the illustration below. You can use either set of terminals on the

speaker. NOTE: Do not remove the jumper wires from between the two sets of terminals when connecting the speaker

wires.

+–

Speaker

Connector Panel

Receiver or Amplifier

(one channel shown)

IMPORTANT: Do not reverse polarities (i.e., “+” to “–” or “–” to “+”) when making connections. Doing so will cause poor

stereo imaging and diminished bass performance.

The 4365’s gold-plated speaker terminals can accept a variety of wire-connector types: bare wire, spade connectors,

pin connectors and banana connectors.

Using Bare Wire or Pin Connectors:

. Unscrew Cap B. Insert Bare Wire or

Pin Connector through

Hole in Post

C. Tighten Cap

to Secure Wire

IMPORTANT: Make sure the (+) and (–) wires or pins do not touch each other or the other terminal. Touching wires can

cause a short circuit that can damage your receiver or amplifier.

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 4 17/06/10 10:23:47

www.jbl.com

English

www.jbl.com

Using Spade Connectors:

A. Unscrew Cap B. Insert Spade Connector

Blades around Post

C. Tighten Cap

IMPORTANT: Make sure the (+) and (–) spade connector blades do not touch each other or the other terminal.

Touching blades can cause a short circuit that can damage your receiver or amplifier.

Using Banana Connectors:

A. Tighten Cap B. Insert Banana Connector

into Hole in Cap

BI-WIRE CONNECTION:

The 4365 connection assembly has two sets of input terminals that are connected by jumper wires. The upper set of

terminals is for high-frequency/ultrahigh-frequency drivers, and the lower set of terminals is for the woofer.

This arrangement allows you to bi-wire the speakers using a single stereo power amplifier or two stereo power

amplifiers. Bi-wiring can offer sonic advantages and more flexibility in power-amplifier selection over a conventional

single-wire connection.

To bi-wire the 4365, first remove the terminal jumper wires as shown in the illustration.

Remove Caps Remove Jumpers from Posts Replace Caps

If you’re bi-wiring with a single stereo power amplifier, connect the speakers according to the following illustration.

Left

Ch.

Right

Ch.

Amplifier

Midrange/

Tweeter

Connection

Woofer

Connection

Left Speaker Right Speaker

Midrange/

Tweeter

Connection

Woofer

Connection

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 5 17/06/10 10:23:47

BI-WIRE CONNECTION (continued):

If you’re bi-wiring with two stereo power amplifiers, connect the speakers according to the following illustration.

Left

Ch.

Right

Ch.

Amplifier 1

Left

Ch.

Right

Ch.

Amplifier 2

Mid/Tweeter

Connection

Woofer

Connection

Left Speaker Right Speaker

Woofer

Connection

Mid/Tweeter

Connection

In either case, follow the instructions for the different connector types in Basic Single-Wire Connection, on page 4.

NOTE: For more information about various speaker-wire and connection options, contact your local JBL dealer.

CONTROLs/aDJUsTMeNTs

The 4365 has stepped front-panel adjustments that let you balance the high-frequency (HF) range and

ultrahigh-frequency (UHF) range against the woofer.

High-Frequency

Trim

Ultrahigh-Frequency

Trim

You can use these controls to adjust the speaker’s sound according to your room’s acoustics or your personal taste. If

you want to return the speakers to their factory-shipped response, set the controls to “0dB.”

As with most speakers, the 4365 has transducers whose suspensions will take several weeks to “break in” and achieve

optimum performance. During this period, the balance between the woofer, HF and UHF drivers may change, so we

recommend that you adjust the HF and UHF controls accordingly.

CaRINg FOR YOUR sPeakeRs

Wipe the cabinet with a clean, dry cloth to remove dust. A damp cloth may dull the cabinet’s finish. Do not use•

volatile liquids such as benzene, paint thinner or alcohol on the cabinet.

Do not spray insecticide near the cabinet.•

To remove dust from the grille fabric, use a vacuum cleaner set to low suction.•

Do not wash the grille in water, as water may fade the grille’s color or make it uneven.•

If the surface of the woofer cone becomes dusty, you can carefully sweep it clean with a soft, dry calligraphy brush•

or paint brush. Do not use a damp cloth.

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 6 17/06/10 10:23:47

English

www.jbl.com

JBL®studio monitor model 4365

Low-frequency transducer: 380mm (15") cone driver with Vented Gap Cooling™, a 100mm (4")

voice coil and a three-layer sandwich cone (model 1501FE)

High-frequency transducer: 100mm (4") compression driver with magnesium-alloy diaphragm and

38mm (1-1/2") exit (model 476Mg)

Ultrahigh-frequency transducer: 25mm (1") compression driver with pure titanium diaphragm (model

045Ti-1)

Recommended ampliﬁer power: 50W – 300W

Frequency response: 35Hz – 40kHz (–6dB, anechoic)

Nominal impedance: 8 ohms

Sensitivity: 93dB (2.83V/1m)

Crossover frequencies: 750Hz, 15kHz

Controls: Switch attenuators for HF and UHF drivers

Enclosure type: 25mm (1")-thick MDF stock, dual-ported

Connector type: Dual gold-plated ﬁve-way binding posts

Finish: Walnut, with polyurethane

Grille color: Monitor blue

Dimensions (H x W x D): 1048mm x 597mm x 429mm (41-1/4" x 23-1/2" x 16-7/8")

Weight: 86.4kg (190 lb)

sPeCIFICaTIONs

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 7 17/06/10 10:23:47

Harman Consumer, Inc.

8500 Balboa Blvd., Northridge, CA 91329 USA

www.jbl.com

JBL and Bi-Radial are trademarks of Harman International Industries,

Incorporated, registered in the United States and/or other countries. Vented Gap

Cooling is a trademark of Harman International Industries, Incorporated.

Features, speciﬁcations and appearance are subject to change without notice.

Part No. 443894-001

0219CSK - JBL Studio Monitor Model 4365 OM v1.indd 8 17/06/10 10:23:47

Table des matières

Autres manuels JBL Intervenants

JBL

JBL JBL4638 Manuel utilisateur

JBL

JBL Control Series Manuel utilisateur

JBL

JBL On tour ibT Manuel utilisateur

JBL

JBL L26 Manuel utilisateur

JBL

JBL 4319 Manuel utilisateur

JBL

JBL LSR6300 Series Mode d’emploi

JBL

JBL ATX10C Manuel utilisateur

JBL

JBL SYNTHESIS FOUR S4Ai Manuel utilisateur

JBL

JBL Charge 2 Manuel utilisateur

JBL

JBL CS68 Manuel utilisateur

JBL

JBL MPro MP418SP Manuel utilisateur

JBL

JBL MEDIA 2000 Manuel utilisateur

JBL

JBL TS60 Manuel utilisateur

JBL

JBL Boombox 2 Manuel utilisateur

JBL

JBL 880 ARRAY Manuel utilisateur

JBL

JBL LOFT50 Manuel utilisateur

JBL

JBL AM5212/66-WH Manuel utilisateur

JBL

JBL LSR2310SP Manuel utilisateur

JBL

JBL Soundfly Air Manuel utilisateur

JBL

JBL Harman WIND3 Manuel utilisateur

JBL

JBL JRX112M Manuel utilisateur

JBL

JBL Harman PARTYBOX 110 Manuel utilisateur

JBL

JBL CBT 70J-1 Manuel utilisateur

JBL

JBL FM52 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur