Jasic L20701 Manuel utilisateur

TMODEL: CUT40(L20701)/CU 0(L208)

OPERATOR’S MANUAL

INVERTER CUTTER

FORWARD

AS60974 and UL60974 standard. Relevant design plans and manufacturing

technologies of this product are patented.

and international standards, and meets GB15579, ICE60974, EN60974,

This product is designed and manufactured according to relevant national

Thank you for JASIC inverter cutter. In order to ensure your safety and

correct operation, please read this manual carefully before operation.

Keep this manual properly for future references.

SHENZHEN JASIC TECHNOLOGY CO., LTD.

Address: No. 3, Qinglan 1st Road, Pingshan District, Shenzhen, Guangdong, China

Postcode: 518118

Tel: 0755-29651666

Fax: 0755-27364108

Website: http://www.jasictech.com

Code: 10057067

Version A3

SAFETY

Precautions for installation

Beware of electric shock!

Install grounding device according to application standard.

Do not touch live parts with naked skin, wet gloves or wet clothes.

Be sure you are insulated from ground and workpiece.

Cover the cover plate of the machine before power on to avoid an

electric shock.

Confirm the safety of your working position.

Beware of fire hazard!

Please install the machine on non-combustible materials to avoid

a fire.

Make ensure there are no inflammables near the cutting position

to avoid a fire.

Beware of explosion !

Do not install the machine in an environment with explosive gas

to avoid an explosion.

Replacing the components can be dangerous.

Only professionals can replace the components of the machine.

Make sure the connecting wires inside the machine are correctly connected after replacing

the PCBs, and then the machine can be run. Otherwise, there is a risk of damage to

property.

Make sure there are no foreign bodies such as wire leads, screws, gaskets and metal bars

falling into the machine inside when replacing the components.

Pay attention to the following when discarding the machine:

Burning the plastic parts such as the front panel may produce poisonous gas.

Dispose it as industrial waste.

cutting

Burning the electrolytic capacitors in the main circuit or on the PCBs may cause an explosion.

Smoke-may be harmful to your health!

Keep your head away from the smoke to avoid inhalation of waste gas

in cutting.

Keep the working environment well ventilated with exhaust or ventilation

equipment when .cutting

Arc radiation-may hurt your eyes and burn your skin!

Use proper mask and wear protective clothing to protect your eyes and

body.

Use proper mask or curtain to protect onlooker from being injured.

Magnetic field can make cardiac pacemaker a bit wonky!

Stay away from the power source to reduce the affect of magnetic filed.

Improper use and operation may result in a fire or an explosion!

Cutting spark may result in a fire, so please make ensure there are no

inflammables near the position, and pay attention to fire safety.cutting

Ensure there is fire extinguisher nearby, and make sure someone has

been trained to operate the fire extinguisher.

Do not weld closed container.

Do not use this machine for pipe thawing.

Hot workpiece can cause severe scald!

Do not touch hot workpiece with bare hands.

Cool the torch for a while after continuously working.cutting

Excessive noise does great harm to people’s hearing!

Wear ear covers or other hearing protectors when .cutting

Give warning to onlooker that noise may be potentially hazardous to

hearing.

Moving parts may injure your body!

Please keep away from moving parts (like fan).

Each door, panel, cover, baffle plate, and protective device the like

should be closed and located correctly.

Seek professional support when trouble strikes!

When trouble strikes in installation and operation, please inspect

according to related contents in this manual.

If you still cannot understand fully, or you still cannot solve the problem,

People with cardiac pacemaker should consult the doctor before carrying

out .cutting

please contact the dealer or the service center of JASIC to obtain

professional support.

Precautions for discard

Precautions for operation

TABLE OF CONTENTS

1. GENERAL DESCRIPTION . . . .

1.1 Model coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Technical parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3 Size and weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.4 Composition and configuration of the machine system . . . . . . . . . . . . . . . . . . . . 3

1.5 Functions and characteristics of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.6 System characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. INSTALLATION AND CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Installation requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Panel functions of L20701 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Notes for cutting operation . . . . . . . . . . . . . . . . . . . . . . . . 11

3.5 Cutting parameters table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4. MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.1 Daily maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.2 Periodic check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . .

. .

cutting . .

. . . . . . . . . . . .

Panel functions of L208 . . . . . . . . . . . .

3.3 Operation method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.4 . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . .

3.6 Replacement of electrode and nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

AC115V/230V

Rated input power supply

Rated output (A/V)

Rated duty cycle(%)

No-load voltage(V)

Efficiency (%)

Items

Models

Single phase

AC240V 50/60Hz

Cooling mode

Insulation grade

Power factor

Rated input capacity KVA( )

Output current range (A)

CUT40(L20701)CUT30(L208)

6.4

40/96

300

20-40

0.3-0 .5

IP21S

0.70

Arc ignition ode m

Post-flow time (S)

Gas pressure range (Mpa)

Enclosure ingress protection

Air cooling

4.6

30/92

325

20-30

Non-HF

0.3- 0.5

IP21S

0.70

Air cooling

1. GENERAL DESCRIPTION

1.1 Model coding

Product code

Code for rated output current

Inverter air plasma cutter

Figure 1 1: Model coding-

1.2 Technical parameters

Table 1 1: General technical parameters-

CUT XX (XXXX)

50/60Hz

Single phase

1.3 Size and weight

Table 1-2: Overall size and weight of the machine

Figure 1-2: Appearance and size of the machine Unit: mm( )

Weight Kg( )

Model

Overall size (L*W*H)

CUT40(L20701)CUT 0( )L208

415*155*315 460*160*320

10.3 11.6

1.4 Composition and configuration of the cutting machine system

1)Composition

Figure 1-3: Composition of the cutting machine system

2 Configuration)

Table 1-3: Configuration of CUT40(L20701)

CUT30

Cutting machine (L208)

300A-6mm

-KDP16D-3m

S45

Name Specification

Quantity pcs ( )

Remark

Material code

Cutting torch

Earth clamp

Operator’s manual

CUT series

Standard configuration

Table 1-4: Configuration of CUT30(L208)

Cutting machine CUT40(L20701)

300A-6mm²

-KDP16D -3m

PT-31

Name Specification

Quantity pcs ( )

Remark

Material code

Cutting torch

Earth clamp

Operator’s manual

CUT series

Standard configuration

1.5 Functions and characteristics of the cutting machine

CUT series are inverter cutting machines made by our company with advanced inverter technology.

They are more mature products with stable performance. With PWM technology and high power

component IGBT, it inverts the DC voltage, which is rectified from 50Hz/60Hz

input AC voltage, to 30K~100KHz AC high voltage. Then the voltage is dropped and rectified to

output the high power DC power supply for cutting. The machine adopts switching power supply

inverter technology, greatly reducing the volume and weight of the cutter, and obviously enhancing

the conversion efficiency by 30%.

Features of CUT series

Economic and practical by adopting compressed air as the plasma gas source. The cutting

speed has increased by 1.8 times when compared with oxyacetylene cutting.

It can cut thick steel plate conveniently and quickly.

It is easy to ignite arc, and post-flow function is available.

It has a wide range of use, especially for cutting stainless steel, copper, cast iron and

aluminum, etc.

With simple operation and high cutting speed, smooth cutting surface can be obtained, and

polishing is unnecessary.

It adopts HF arc ignition mode.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Jasic Système de soudage

Jasic

Jasic TIG 200 Dual Voltage Manuel utilisateur

Jasic

Jasic TIG Series Manuel utilisateur

Jasic

Jasic Plasma Cut 100 Manuel utilisateur

Jasic

Jasic TIG200 Manuel utilisateur

Jasic

Jasic MIG 270S Manuel utilisateur

Jasic

Jasic JM-160C Manuel utilisateur

Jasic

Jasic MIG 350C Manuel utilisateur

Jasic

Jasic TIG180P Manuel utilisateur

Jasic

Jasic MIG160PFC Manuel utilisateur

Jasic

Jasic EVO 2.0 EP-45 Manuel utilisateur

Jasic

Jasic MIG 350 Compact Manuel utilisateur

Jasic

Jasic MIG 270 Separate Manuel utilisateur

Jasic

Jasic Arc 140 Manuel utilisateur

Jasic

Jasic TIG 200 AC/DC Digital Series Manuel utilisateur

Jasic

Jasic EVO 2.0 Manuel utilisateur

Jasic

Jasic TIG200PACDC PFC Manuel utilisateur

Jasic

Jasic VIPERMIG 180i Manuel utilisateur

Jasic

Jasic MIG SERIES Manuel utilisateur

Jasic

Jasic ARC 160GS Manuel utilisateur

Jasic

Jasic EVO 2.0 Manuel utilisateur

Jasic

Jasic PT100 Manuel utilisateur

Jasic

Jasic EVOLVE 200 Manuel utilisateur

Jasic

Jasic Cut 160 Manuel utilisateur

Jasic

Jasic MIG SERIES Manuel utilisateur

Manuels Système de soudage populaires d'autres marques

Berner

Berner PLASMACUT 54 Manuel utilisateur

Pro Spot

Pro Spot PR-155 Manuel utilisateur

Forney

Forney 210 Manuel utilisateur

Thermal Arc

Thermal Arc 400S Manuel utilisateur

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuel utilisateur

GYS

GYS PROTIG 201 AC/DC Manuel utilisateur

TAFA

TAFA 30*8B35 Manuel utilisateur

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur

ESAB

ESAB Buddy Arc 145 Manuel utilisateur

CIGWELD

CIGWELD 636804 Guide rapide

Red-D-Arc

Red-D-Arc DC-400 Manuel utilisateur

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuel utilisateur

WIA

WIA Weldmatic 270 CP132-2 Manuel utilisateur

Sonics

Sonics H520T Manuel utilisateur

Miller

Miller Big Blue 400D Manuel utilisateur

NewArc

NewArc RT2000 Guide de démarrage rapide

Hypertherm

Hypertherm powermax1000 Manuel utilisateur