JanSan JS-BP31 Manuel utilisateur

Back Pack Vacuum

OWNER’S MANUAL

Model: JS-BP31

DistributedBy:

Po Box 14065

Merrillville, IN 46411

866-350-7160

www.JanSanMFG.com

Doc #: 98-20015

Rev: 04/2011

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precaution should always be followed, including the

following:

READ ALL INSTRUCTIONS

BEFORE USING (THIS APPLIANCE)

WARNING-To reduce the risk of fire, electric shock, or injury:

1. Do not leave vacuum cleaner when plugged in. Unplug from outlet when no use and before

servicing.

2. To reduce the risk of electric shock, do not use outdoors or on wet surfaces

3. Use only as described in this manual. Use only manufactures recommend attachments.

4. Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been

dropped, damaged, left outdoors, or dropped into water, enter it to a service center.

5. Do not pull or carry on cord, use cord as a handle, close door on cord, or pull cord around

sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated

surfaces.

6. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

7. Do not handle plug or vacuum cleaner with wet hands.

8. Do not put any object into openings. Do not use with any opening blocked. Keep

free of dust, lint, hair and anything that may reduce airflow.

9.Keep hair, loose clothing, fingers and all parts of body away from openings and

moving parts.

10.Turn all controls off before unplugging.

11.Use extra care when cleaning on stairs.

12.Do not use to pick up flammable or combustible liquids, such as gasoline, or use in

areas where they may be present

13.Hold plug when rewinding onto cord reel. Do not allow plug to whip when

rewinding.

14.Unplug before connecting the hose

15.Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

16.Do not use without dust bag and/or filter in place.

17.If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similarly qualified person in order to avoid a hazard.

SAVE THESE INSTRUCTIONS

Precautionary Measures

Important: If the suction opening of the unit, the hose or the extension tubes are

BlOCKED. Switch off the vacuum cleaner and remove the blocking substance

before you start the unit again.

1.Before inserting the power plug 4. Do not pick up anything that is

into the wall outlet, make sure that burning or smoking such as

your hands are dry. cigarettes, matches or hot ashes.

2. Before you start vacuuming. 5. Do not use without all filters and

make sure to remove large or dust bag in place.

Sharp objects that might 6. Do not vacuum any liquids.

3. When pulling out the power plug 7. Keep hair, loose clothing, fingers,

from the wall outlet, pull the plug feet and all parts of body away

Notthepowercord. fromopenings,rotatingagitator

andothermovingparts

GETTING TO KNOW YOUR BACK PACK VACUUM

Ref#Part#PartDescription

MainUnit

ExhaustGrill

50‐10030 On/OffPowerSwitch

CanisterLidTabs

WaistBand

ShoulderStraps

50‐40078 BackBoardPanel

50‐40079 CarryHandle

HoseInlet

50‐40080 CanisterLid

50‐40081 FlexibleHose

50‐40082 FlexibleHosehandle

VariableSuctionControl

TelescopicTubeReleaseButton

Ref#Part#PartDescription

50‐40083 TelescopicTube

WaistBandBackSupportPanel

WaistBandToolCarrier

50‐40084 DustingBrush

50‐40085 CreviceTool

50‐40086 BlowerPort

50‐40087 PetHairRemover

50‐40088 FloortoCarpetBrush

50‐40089 AirDrivenTurboBrush

50‐40090 BlowerAttachments(×3)

25(a)

40‐21002 HEPADustBag(soldin6pk)

25(b)

40‐21003 PaperDustBag(soldin6pk)

50‐60005 Shake‐OutBag

50‐60006 HEPAPre‐MotorFilter

50‐60007 ExhaustFilter

Operating Instructions

Warning: To reduce the risk of electric shock, the power cord must be

Disconnected before removing the dust bag, shake-out bag,

Changing the filters or performing maintenance or trouble-

Shooting checks.

Assembling Your Vacuum 5 The cardboard face of the new bag should

Cleaner restsecurelyinthedustbagcoverguides

Note: Always remove the power plug (Fig. 3)

from the wall outlet before assembling

or removing accessories.

Inserting the HEPA Dust Bag

Note: This unit can be used with the shake-

Outbagalone,howeveritmustbecleaned Fig.3

after every use if there is no HEPA dust bag 6 Ensure that the shake-out bag is in place.

installed. (Fig.4)

Important: Do NOT usethevacuumwith

Out all filters, shake-out bag, and with or without

HEPA dust bag in place.

1. Unplug the hose connecting power cord and

remove the flexible hose.

2. To open the canister lid press on the canister

lid tabs on each side of the unit and lift canister lid.

(Fig.1)

Fig.4

7FliptheHEPA bag holder over, pressing

the tab on the bag holder until it clicks,

thenreplacethecanisterlid.

8Thecanisterlidcanbereplacedonthe

Fig.1 unit with the hose opening on the right

3. Pull the tab on the HEPA dust bag holder out or left, as per your preference. (Fig 5)

slightlyandflipupwards.(Fig2)

4.Holding the HEPA dust bag in your hand, slice it

firmly between the slots in the bag holder. (Fig 2)

Fig. 2 Fig. 5

Operating Instructions

Attaching the Flexible hose to 3Toremovethetelescopictubefrom

The vacuum theflexiblehose,pressonthetelescopic

The flexible hose should be tube release button and pull it out.

connectedtothevacuumbefore (Fig.9)

strapping the unit to you back.

1. To connect the flexible hose into

the hose inlet, insert the threaded end

oftheflexiblehoseintothehoseinletand Fig.9

turn counter-clockwise until it locks into Note: Always remove the power plug from the

place.(Fig6) walloutletbeforeassemblingorremoving

accessories.

Manual Suction Control

Fig. 6 Your vacuum cleaner includes a manual variable

suction control on the flexible hose handle. The

suctionpowercanbeadjustedbymovingthe

suctionregulatortothedesiredpositionbetween

Open and Closed. (Fig. 10)

2. Plug the power cord into the Open gives you less suction, closed maximum

electrical outlet. Suction. For example, less suction is required on

3. To remove the flexible hose, unplug upholstery and draperies compared to thick

the power cord and then turn the hose carpets, which require maximum suction.

clockwise and pull the flexile hose out.

Attaching the Telescopic Tube to the

Flexible hose Handle

1 Holding the telescopic tube, insert the

handle into the telescopic tube receptacle.

pushthehandlein.(Fig.7) Fig10

Using the Floor to Carpet Brush

1.Toattachthefloortocarpetbrushto

Fig. 7 the telescopic tube, insert the telescopic

2 Push forward on the plastic button and tube into carpet to floor brush. (Fig.11)

pull the inner tube outward to extend for

alongerreach.(Fig.8)

Fig.8 Fig.11

Operating Instructions

2 Step on the floor to carpet selector Using the Air Driven Turbo Brush

to adjust the height of the brushes.

there are two(2) different heights Warning: To reduce the risk of electric shock , the

one for floors and one for carpets. power cord must be disconnected before removing the

(Fig. 12) HEPA dust bag, the shake-out bag,

HEPA pre-motor filter, changing the filters or performing

maintenanceortroubleshootingchecks.Theefficiency

of your air driven turbo brush depends on the bristle

brushrotatingathighspeed.

Strongairsuctionisneededto

accomplishthis.Inordertoensurethat

Fig12 . maximumairsuctionismaintained,

3 To remove the telescopic tube from please read the following instructions:

the floor to carpet brush, pull the 1. Change the HEPA dust bag or empty

telescopic tube out from the floor to the shake-out bag frequently.

carpet brush. 2. Replace the pre-motor and

Using the Attachments exhaustfiltersasneeded.

Dusting Brush 3. Ensurethattherotatingbrushis

The dusting brush is used for the furniture kept free of hair and string which may accumulate

Crevice Tool anddecreasebrushperformance.

Use for radiators, crevices, corners, 4. To attach the air driven turbo brush,

baseboards and between cushions. insert the telescopic tube into the air

Pet Hair Remove Brush driventurbobrush.

The pet hair remove brush 5. To adjust the suction control on the air

is used for upholstery. The driven turbo brush slide the suction control

unique surface make s it an for more or less suction as desired

excellent tool for removing Note: The driven turbo brush has a suction

unwanted pet hair. Control on the top of the brush.

Note: This tool is not a grooming tool Open or close to increase or decrease

and should not be used on animals. the suction as desired, I, e, open for high

Caution: Do not use pet hair pile or closed for low pile carpets

Remove brush on delicate or woven Using the Blower Attachments

Fabrics that may snag, The blower attachments are extremely

Do not use pet hair remover brush on Useful for vacuuming in hard to reach crevices

Wooden floors as this accessory might and small compartments such as in cars.

Cause mild scratching. Important Note: When blocking the air holes,

Blower Attachments grasp the blower attachment firmly so that they

The blower attachments can be used do not blow off

With the vacuum to pick up very fine dirt Note: Do not use blower function to clear dust

Particles in tight crevices or spots, or to . Off of fragile or delicate objects unless they are

Inflate inflatable items or air mattresses. secured or held firmly in place as the blower

Actionisquitestrongandcausedamage.

Operating Instructions

The blower attachments have air bleed 5.To blow up inflatable items, select

holes.these air bleed holes help the appropriate size blower

relieve some air pressure so that the attachment that will fit into the air

attachment does not blow off. However, valve.(Fig.16)

should an increase in air pressure be

desired,simply cover one or more of

the air bleed holes.

To use the blower attachments:

1．Pull up and hold the exhaust tab, Fig.16

with the free hand pull out the

exhaust grill.(Fig.13)

6.Turntheunitonandholdtheblower

attachmentandairvalvewhhiethe

vacuumexhaustispumpingairinto

theinflatable.

7.Todetachtheflexiblehoseturn

Fig.13 clockwise and pull out from blower

2．Remove the exhaust filter. port.

3．To place the blower port into the Note:Firmly hold the flexible hose by

exhaust outlet,align the lower tabs the attachment when blowing dirt or

on the blower port with the slots on dust off of objects.

the exhaust.Pull up on the exhaust Using Your Vacuum

tab and push the top of the blower 1. Insert the power plug into the wall outlet.

port until it snaps into place. 2. Connect hose and telescopic tube if desired.

(Fig.14) 3. Correctly place shoulder straps on

each shoulder and secure the waist

band with hook and loop strips.

(Fig. 17)

Caution:If the waist band and both

Fig.14 Shoulderstrapsarenotproperlyand

4. To attach the hose to the blower Securely in place the umit could fall off

port,align the flexible hose and turn Your back causing damage or injury.

counter-clockwise until it stops.The

hose is now securely in place.

(Fig. 15)

Fig. 15 Fig. 17

Operating Instructions

4. Turn the unit on by pressing the 3. Holding the HEPA dust bag in your

switch located near the base of the hand,slide it out from the slots in

unit to turn the vacuum cleaner on. the bag holder .Hold carefully in

(Fig.18) ordertoavoidhavingdustfalloutof

HEPA dust bag.(Fig. 20)

Fig. 18

Fig. 20

Removing & Replacing HEPA

Dust Bag 4.ReplacetheHEPA dust bag with a

To remove the HEPA dust bag from the new bag. Do not reuse the same

vacuum: bag.

Important: DO NOT use the vacuum 5. The cardboard face of the new bag

without all filters,shake-out bag, and should rest securely in the dust

with or without HEPA dust bag in place. bag cover guides.(Fig. 21)

1. To remove the HEPA dust bag,

press on the canister lid tabs on

each side of the unit and lift canister Fig. 21

lid.(Fig.19)

6.Replacetheshake-outbagintothe

vacuum.

7.ToreplacetheHEPA dust bag

holder,fliptheholderandpresstab

untilitclicks.

8.Replacethecanisterlidontothe

Fig.19 vacuum.

2. Pull the tab on the HEPA dust bag Warning: Never over fill the HEPA

holder out slightly and fliy upwards. Dust bag –replace when bag is full and

(Fig.19) clean the shake-out bag and filter each

TimetheHEPA dust bag is replaced.

Warning: To reduce the risk of electric shock, the power cord must be

disconnected before removing the dust bag, shake-out bag,

changing the filters or performing maintenance or trouble-

shootingchecks.

Operating Instructions

Cleaning & Replacing the Cleaning the HEPA Pre-Motor

Shake-OutBag Filter

Note: Clean the shake-out bag out- Important, Please Note:

doors when changing the HEPA dust TheHEPA pre-motor filter will stop

bag. Optimum performance is achieved most of the tiniest dust particles and

by using the HEPA dust bag with the airborne allergens from re-entering the

shake-out bag decreasing the need for air you breathe. In fact it stops 99.97%

washing the shake-out bag. of all particles as small as 0.3 microns-

Cleaning the Shake-Out Bag when many times smaller than a human hair!

Used with the HEPA Dust Bag: Becauseofthisincrediblefiltration

1. Remove the shake-out bag,holding performance, the HEPA pre-motor filter

The handle at the bottom of the bag, will accumulate many fine dust particles

shake out doors vigorously over a that are difficult to see. Be assured that

garbage receptacle until there is no the HEPA pre-motor filter is doing the

moredust. job.CleantheHEPA pre-motor filter

2. Inspect shake-out bag regularly for after each use as described in this

tearsordamage.Replaceshake- section

out bags if damage or tears are present. 1. Remove the shake-out bag from the

Cleaning the Shake-Out Bag when canister. The HEPA pre-motor filter

Used Alone: islocatedundemeaththeshake-out

1. Remove the shake-out bag,empty bag. To remove the HEPA pre- contents into a

trash can, and shake motor filter, lift the form the

vigorously out doors until there is no sides of the HEPA filter.

moredust. 2. Vigorously”TapClean”theHEPA

2. The shake-out bag is hand wash- pre-motor filter on a hard surface to

ableinlukewarmwater. removeanyresidualdustthatmight

3. Allow to air dry for 24 hours. The stillbeontheHEPA pre-motor filter.

shake-out bag should be replaced 3. You can wash the HEPA pre-motor

when needed. Neverreplaceinto filter by running it under the tap and

the vacuum if still wet. allowing the water to run on the dirty

Note: If used often without HEPA dust side at least once a month or when

bag, replacement and washing will be suction appears to be decreased.

required more often

4. Replace clean shake-out bag in

Unit ,and replace the canister lid

Onto the vacuum.

Warning: To reduce the risk of electric shock, the power cord must be

disconnected before removing the dust bag, shake-out bag,

changing the filters or performing maintenance or trouble-

shootingchecks.

Table des matières

Autres manuels JanSan Aspirateur

JanSan

JanSan WideVac Manuel utilisateur

Manuels Aspirateur populaires d'autres marques

Bissell

Bissell LittleGreen Proheat 1425 Series Manuel utilisateur

Panasonic

Panasonic MC-YL637S147-AE Manuel utilisateur

NEFF

NEFF N17XH10 0 Series Manuel utilisateur

LG A9 Series Manuel utilisateur

Oreck

Oreck Cordless Captura BK51700 Series Manuel utilisateur

Kogan

Kogan KAVACROBVWA Manuel utilisateur

Kränzle

Kränzle VENTOS 50 ID Guide de l'utilisateur

EVVO

EVVO Ai35 Manuel utilisateur

DeWalt

DeWalt DWH200D Manuel utilisateur

Pontec

Pontec Pondomatic Vacuum Cleaner Manuel utilisateur

Cleanmaxx

Cleanmaxx PC-P007E Manuel utilisateur

Exido

Exido 240-114 Manuel utilisateur

RIDGID

RIDGID WD1685AU0 Manuel utilisateur

Ezviz

Ezviz RE4P Manuel utilisateur

STG global

STG global TANVAC HDV3000 Manuel utilisateur

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manuel utilisateur

Factory

Factory M3340 Manuel utilisateur

Shop-Vac

Shop-Vac VN92 SERIES Manuel utilisateur