Janome 1200D Manuel utilisateur
PARTS LIST
&
SERVICE MANUAL
MODEL: 1200D
First Edition: 21 February 2019
SERVICE MANUAL
TABLE OF CONTENTS
A.General directions and recommendations
B. Recommendations
C. Mechanical sewing disorders
D. Adjustment of the automatic tension unit
E. Position of program selection - display drum indicator and display window
F. Position of display drum indicator and upper looper shifting cam
G. Adjustment of the Chain looper tension dial
H. Gauge for the after - sales service
1. Removing Machine Base and Back Cover
2. Removing Front Cover and Mounting Covers
3. Angular position of balance weights and position of eccentrics
4. Height and alignment of cloth presser bar
5. Height and orientation of needle bar in relation to the needle plate holes
6. Height - clearance - angular position of lower looper
7. Clearance of needle guards
8. Timing of lower looper
9. Angular position of upper looper
10. Clearance and timing of upper looper to lower looper
11. Chain looper : angular position - clearance - orbital timing - clearance of
chain needles guards
12. Chain looper thread take up rotary cam
13. Height of feed dog
14. Upper knife and vertical feed timing
15. Horizontal feed timing against chainstitch needle
16. Differential feed
17. Position of fixed cutter and cutting width dial setting
18. Position of loopers threads take up lever
19. Safety device - Presser foot
20. Top Cover device
ANNEX
Tools for setting SL/DF Dials
Setting positions of SL/DF Dials
Clearance between Feed Dog and Needle Plate
Trouble shooting - Cover Hems
Cover Hem stitch formations
1
GENERAL DIRECTIONS AND RECOMMENDATIONS A
Safety
For safety reasons, the sewing machine must
be disconnected from the mains:
- Whenever the machine is left unattended
- Whenever preparing the machine for sewing
- Whenever servicing
- Whenever replacing mechanical or electrical parts or accessories
Needles
Usually needles of the system 130/705 H may be used. However, in certain
cases stitch quality may be improved by using type ELX 705 needles.
Choose needle size No.80 for sheer materials and No.90 for normal or thick materials.
Threads
Choose a good quality polyester thread or blended thread.
Lubrication
Besides the 2 oiling points marked in red, the machine is equipped with
self-lubrication bearings and parts. Lubricate the machine as follows: when using it
for the first time - if it has not been used for some time - when it has been intensively
used for 7 to 8 hours.
2
RECOMMENDATIONS B
1. Never connect the machine to a different voltage than that marked on the specification
plate.
2. For safety reasons, never perform any repairs on the power supply circuit without
first removing the mains lead from the machine.
3.
4.
Never plug in or run the machine unless all the connections are correctly set.
When changing the light bulb, it is neccessary to disconnect the mains lead.
3
4
MECHANICAL SEWING DISORDERS C1
First of all, please refer to the paragraph entitled "maintenance" in the instruction
manual, especially when machine does not turn freely by turning the flywheel by hand.
If necessary, check and adjust tightness of motor belt.
Given below are the most frequent disorders. In most cases, they can be remedied by
checking the adjustments in the following order. However, before checking the
adjustments, make sure that the threading is correct and that all the thread passages
are okay.
1. Skipped overlock stitches
Check and adjust if necessary:
- Needle bent or with a dull point - replace needle
- Needle not set correctly - refer to "changing the needle" in the instruction manual
- Burrs on upper or lower looper - polish
- Burrs on chaining finger - polish
- Excessive tension on the needle thread
- Height and orientation of needle bar
- Clearance between point of lower loopers and needle
- Clearance between upper and lower loopers
- Timing of upper and lower loopers against needle
- Feed timing
2. Skipped chainstitches - Cover hems
Check and adjust if necessary:
- Needle and chain looper thread tensions not balanced
- Needle bent or with a dull point - replace needle
- Needle not set correctly - refer to "changing the needle" in the instruction manual
- Burr on chain looper - replace or polish
- Upper knife is dull - replace
- Chain looper needle clearance
- Chain needle guard clearance
- Angular position of chain looper
- Orbital timing of chain looper
- Chain thread take up lever timing
- Height and orientation of needle bar
- Needle plate spring plate bent
-
Clearance and position between back of chain looper and needle L0
Note: For more information, see pages .
MECHANICAL SEWING DISORDERS C2
3. Thread breakage
Before checking the adjustment, make sure of the good quality of the thread and the
needle, the correctness of threading and the smoothness of all the thread passages.
Quite often, a damage to thread passage is the cause of thread breakage. If all these
points are in order, check the following:
- Dull point of needle or bent needle - replace.
- Dull or burred point of looper - replace.
- Scratch or injury on chaining finger of needle plate - replace.
- Too strong thread tension.
- Unsmooth or injured edge of needle hole on needle plate (thread breakage of chain
stitches) - replace.
4. Irregular stitches
- Inadequate setting of thread tensions - re-adjust.
- Unsmooth thread passage - polish.
- Height of feed dog.
- Position of looper thread take up levers and thread guides.
- Upper knife is dull - replace.
- Damage on needle plate face or presser foot sole - replace.
- Incorrect alignment of thread guide bar with spool pins - reset it at correct
position to align to spool pins.
5. Breakage of needle
Check and adjust if necessary
- Dull point of needle or bent needle - replace.
- Incorrect placement of needle - refer to "changing the needle" in the instruction manual. .
- Clearance of needle guard and (chain needle).
- Incorrect alignment of needle holes of presser foot and needle plate.
- Clearance from needle to lower looper.
- Clearance between the upper and lower loopers.
- Feed timing.
- Horizontal feed timing against chain-stitch needle.
5
ADJUSTMENT OF THE AUTOMATIC TENSION UNIT D
d
B
B
r
s
6
s
r
+
-
E
1. Remove: Mains lead - Front cover.
2. Select sewing program 1 "SAFETY 4THREAD"
3. Check and make sure that the lever "h" is facing the notch of tension cam "g" for
yellow needle thread.
4. If not loosen screw "a" and turn DT cam pulley "j" forward or backward until the
lever "h" is facing the notch of tension cam "g". Then, tighten screw "a".
5. If the position of the display drum indicator "d" is not aligned with the display
window "e", then loosen screw "c" and adjust the position of drum.
6. Fasten screw "c" and recheck the position of the display drum "d".
Note: In order to check the alignment of the display drum indicator "d" and the disolay
window "e", it is necessary to set the front cover on to machine.
POSITION OF PROGRAM SELECTION-DISPLAY DRUM INDICATOR
AND DISPLAY WINDOW
g
a
c
h
de
SELECT
h
g
b
d
2 mm
j
7
POSITION OF THE DISPLAY DRUM INDICATOR
& UPPER LOOPER SHIFTING CAM F
8
1. Remove: Mains lead - Front cover
2. Make sure if tension cams and levers are set in proper positions when selecting
sewing program 1 "SAFETY 4THREAD" (See and Check Page E).
3. Select sewing program 10 "COVER HEM/CHAINSTITCH".
4. Bring the needle bar to its lowest position by turning a handwheel toword you.
5. Loosen screw "a" and turn the upper looper shifting cam "b" until the hook of the
looper follower "c" falls into the V-shaped holl ow of the cam "b" ʻSee View A ).
Check if a cam "b" and looper follower "c" are positioned as own in View B .
6. Fasten screw "a" and recheck if the upper looper shifting connector "d" is pulled
up by a spring.
view A b
c
view B
b
c
a
a
b
c
d
A
SELECT
2 mm
1.0~1.5mm
B
Autres manuels pour 1200D
6
Table des matières
Autres manuels Janome Machine à coudre
Janome
Janome MC230E Manuel utilisateur
Janome
Janome S521 Manuel utilisateur
Janome
Janome CoverPro 1000CP Manuel utilisateur
Janome
Janome S750 Manuel utilisateur
Janome
Janome SKYLINE S6 Manuel utilisateur
Janome
Janome Sewing Machine Manuel utilisateur
Janome
Janome RSS C30 Manuel utilisateur
Janome
Janome myLock 134D Manuel utilisateur
Janome
Janome 2222 Manuel utilisateur
Janome
Janome JF Series Manuel utilisateur
Janome
Janome MB-4 Manuel utilisateur
Janome
Janome Memory Craft 3500 Manuel utilisateur
Janome
Janome Myexcel 23X/MX3123 Manuel utilisateur
Janome
Janome Pro-Stitcher PREMIUM Quilt Maker Pro 16 Manuel utilisateur
Janome
Janome NH22 Manuel utilisateur
Janome
Janome Memory Craft 3000 Manuel utilisateur
Janome
Janome Mylock 634D Manuel utilisateur
Janome
Janome 1600P-QC - Manuel utilisateur
Janome
Janome Memory Craft 6700P Manuel utilisateur
Janome
Janome 9102D - Manuel utilisateur
