Jandy PureLink Manuel utilisateur
Installation and Operating Data
H0573500-
Installation and
Operation Manual
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a professional pool/spa
service technician. The procedures in this manual must be followed exactly. Failure to follow
warning notices and instructions may result in property damage, serious injury, or death.
Water Purication System
Power Center and Cell Kit
For use with
Page 3
Section 1. Safety Information ....................... 4
Section 2. System Description ...................... 5
2.1 ElectricalSpecications............... 6
Section 3. Installation Instructions Model
PureLink AP700 and AP1400 ...... 8
3.1 Materials and Tools...................... 8
3.2 PlumbingCongurations ............. 8
3.2.1 Recommended Plumbing
Conguration....................... 8
3.2.2 Alternate Plumbing
Congurations ..................... 9
3.3 Installing AquaLink RS PureLink
Power Center................................ 12
3.4 Earth Bonding (Grounding) ......... 13
3.5 Installing the APURE700 and
APURE1400 Cell and Flow/Temp/
Salinity Sensor ............................. 14
3.6 Connection to the AquaLink®RS
PureLink Control System............. 16
Section 4. Pool Water Preparation ................ 17
4.1 Determining Pool Size
(m3of Water)................................ 17
4.2 Determining Pool Size (Gallons). 17
4.3 Selecting Model Size ................... 18
4.4 Chemistry You Need to Know ..... 18
4.5 Optimum Pool Water Conditions 19
4.6 Chlorine Testing .......................... 19
4.7 Salt (NaCl sodium chloride) ....... 19
4.7.1 What Type of Salt to Use?... 19
4.7.2 How Much Salt to Use?....... 20
4.7.3 How to Add Salt to the Pool? 20
Section 5. Operating Instructions.................. 23
5.1 Using the Front Panel Controls.... 23
5.2 Reading the Display..................... 24
5.3 Operation...................................... 25
5.4 Startup.......................................... 26
5.4.1 Shocking .............................. 26
5.4.2 Apply Power........................ 26
5.5 Operating in Winter...................... 26
5.6 Recommendations........................ 27
Section 6. User Maintenance Instructions .... 28
6.1 Daily............................................. 28
6.2 Weekly ......................................... 28
6.3 Monthly........................................ 28
6.4 Electrolytic Cell Cleaning............ 28
6.5 Flow/Temp/Salinity Sensor
Cleaning ....................................... 29
6.6 Winterizing................................... 30
Section 7. Troubleshooting ........................... 31
7.1 Problems and Corrective Action .. 31
7.2 Service Codes............................... 34
7.3 Additional Letter Codes............... 34
Section 8. Temperature Conversion.............. 35
Section 9. AP700 and AP1400 Exploded Views
and Replacement Kits .................. 36
9.1 AquaLink RS PureLink Power
Center........................................... 36
9.2 2” PVC Union, Electrolytic Cell.. 37
9.3 PureLink Flow Sensor.................. 37
Table of Contents
Page 4
WARNING
To reduce the risk of electric shock, re or injury, service should only be attempted by a qualied Pool Service
Professional.
WARNING
When mixing acid with water, ALWAYS ADD ACID TO WATER. NEVER ADD WATER TO ACID.
WARNING
Do not operate electrolytic cell without proper ow or water circulation. A buildup of ammable gases would
result in hazardous conditions.
WARNING
RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH.
Installation must be done in accordance with the National Electric Code (NEC, NFPA-70) and/or any other
applicable local and national installation codes.
A green colored terminal (or a wire connector marked “G”, “GR”, “Ground” or “Grounding”) is provided within
the terminal compartment. To reduce risk of electric shock, connect this terminal or connector to the grounding
terminal of your electric service or supply panel with a conductor equivalent in size to the circuit conductors
supplying this equipment.
Power supply must be interconnected with Pool Pump motor power source. This insures the chlorinator and
pool pump will turn on and off together.
Use of chemicals other than those recommended may be hazardous. Follow the Chemical Manufacturers
Instructions.
It is recommended that the water Flow/Temp/Salinity Sensor is installed in the same piping as the electrolytic
cell, without any valves or diverters between them. (See Figure 1).
The Flow/Temp/Salinity Sensor must be mounted as in Figure 12.
Section 1. Important Safety Instructions
READ AND FOLLOW ALL INSTRUCTIONS
LIRE LA NOTICE TECHNIQUE.
All electrical work must be performed by a licensed electrician and conform to all national, state, and
local codes. When installing and using this electrical equipment, basic safety precautions should always be
followed, including the following:
DANGER
To reduce the risk of injury, do not remove the suction ttings of your spa or hot tub. Never operate a spa or hot
tub if the suction ttings are broken or missing. Never replace a suction tting with one rated less than the ow rate
marked on the equipment assembly.
WARNING
To Reduce the Risk of Injury -
a) The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and
104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young
children and when spa use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of
pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).
c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate
thermometer since the tolerance of water temperature-regulating devices varies.
d) The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to unconsciousness with
the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system
problems, or diabetes should consult a physician before using a spa.
f) Persons using medication should consult a physician before using a spa or hot tub since some medication
may induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
Page 5
WARNING
Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature
of the body reaches a level several degrees above the normal body temperature of 98.6° F. The symptoms of
hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of the
body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat; 3)
failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women; 6)
unconsciousness resulting in a danger of drowning.
WARNING
Risk of electric shock - Install the power center at least ve (5) feet (152.4cm) from the inside wall of the pool
and/or hot tub using non-metallic plumbing. Canadian installations must be at least three (3) meters from the
water.
Children should not use spas or hot tubs without adult supervision.
Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment.
People using medications and/or having an adverse medical history should consult a physician before using a spa
or hot tub.
AVERTISSEMENT
Danger d'electrocution - Les installations Canadiennes doivent se trouver à au moins trois (3) mètres de l’eau.
Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance.
Pour éviter que les cheveux ou une partie du corps puissent être aspirés, ne pas utiliser une cuve de relaxation si
les grilles de prise d'aspiration ne sont pas toutes en place.
Les personnes qui prennent des médicaments ou ont des problèmes de santé devraient consulter un médecin
avant d’utiliser une cuve de relaxation.
WARNING
People with infectious diseases should not use a spa or hot tub.
To avoid injury, exercise care when entering or exiting the spa or hot tub.
Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible
drowning.
Pregnant or possibly pregnant women should consult a physician before using a spa or hot tub.
Water temperature in excess of 100°F/38°C may be injurious to your health.
Before entering a spa or hot tub measure the water temperature with an accurate thermometer.
Do not use a spa or hot tub immediately following strenuous exercise.
Prolonged immersion in a spa or hot tub may be injurious to your health.
Do not permit any electric appliance (such as a light, telephone, radio, or television) within 5 feet (1.5 m) of a spa
or hot tub.
The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.
Water temperature in excess of 100°F/38°C may be hazardous to your health.
AVERTISSEMENT
Les personnes atteintes de maladies infectieuses ne devraient pas utiliser une cuve de relaxation.
Pour éviter des blessures, user de prudence en entrant dans une cuve de relaxation et en sortant.
Pour éviter l’évanouissement et la noyade éventuelle, ne prendre ni drougue ni alcool avant d’utiliser une cuve de
relaxation ni quand on s’y trouve.
Les femmes enceintes, que leur grossesse soit conrmée ou non, devraient consulter un médecin avant d’utiliser
une cuve de relaxation.
Il peut être dangereux pour la santé de se plonger dans de l’eau à plus de 38°C/100°F.
Avant d’utiliser une cuve de relaxation mesurer la témperature de l’eau à l’aide d’un thermomètre précis.
Ne pas utiliser une cuve de relaxation immédiatement après un exercice fatigant.
L’utilisation prolongée d’une cuve de relaxation peut être dangereuse pur la santé.
Ne pas placer d'appareil électrique (luminaire, téléphone, radio, téléviseur, etc) à moins de 1.5m de cette cuve de
relaxation.
La consommation d’alcool ou de drogue augmente considérablement les risques d’hyperthermie mortelle dans
une cuve de relaxation.
Il peut etrê dangereux pour la santé de se plonger dans de l’eau à plus de 38°C/100°F.
Page 6
CAUTION
A terminal bar marked "GROUND" is provided within the power center. To reduce the risk of electrical shock,
connect this terminal bar to the grounding terminal of your electric service or supply panel with a continuous
copper conductor having green insulation and one that is equivalent in size to the circuit conductors supplying this
equipment, but no smaller than no. 12 AWG (3.3mm). In addition, a second wire connector should be bonded with
a no. 8 AWG (4.115mm) copper wire to any metal ladders, water pipes, or other metal within ve (5) feet (1.52m)
of the tub.
SAVE THESE INSTRUCTIONS
Attention installer: Install to provide drainage of compartment for electrical components.
WARNING
To avoid injury ensure that you use this control system to control only packaged pool/spa heaters which have built-
in operating and high limit controls to limit water temperature for pool/spa applications. This device should not be
relied upon as a safety limit control.
Page 7
Section 2. System Description
2.1 Product Description
The PureLink System is an all-in-one, Chlorine Generator and Control System Power Center and Cell Kit
for use with AquaLink RS PDA, All Button, or OneTouch controllers.
ATTENTION INSTALLER: Various application notes (including more detailed
instructions) are available from the Dealer covering installation, operation,
maintenance, and plumbing of the chlorinator system.
Figure 1. Typical PureLink Installation With Options
AquaPure
Pump
Filter
AquaLink RS
PureLink
Power Center
Flow/Salinity Sensor
Cell
Heater
Spa IntakePool Intake
Spa ReturnPool Return
Options List
1. ORP/External Control Interface
2. ORP/Freeze Control Unit
3. Heater
ORP Unit
(Control Signal from ORP Unit to
ORP Interface/Aux Board)
The PureLink Power Center and Cell Kit uses a process known as electrolysis to produce sodium
hypochlorite (liquid chlorine) from a low concentration of salt added to the pool water. Hypochlorite kills
bacteria, oxidizes organic material, and kills algae then reverts back to salt. The PureLink then reuses the
salt and the process starts over again. The PureLink system is comprised of the following three component
parts.
Power Center The AquaLink RS PureLink Power Center converts AC electrical current to a low
voltage DC current which is required by the cell to perform the electrolysis. The
power center is connected with the pool circulation pump electrical source so that
theelectrolyticcellonlyoperateswhenthepoolpumpison.Theowportionofthe
Flow/Temp/Salinity Sensor is a backup device only.
Detail A
Detail B
Detail C
Preferred
Not Preferred
Hazardous
Page 8
Electrolytic Cell The PureLink electrolytic cell contains bipolar electrodes which perform the
electrolysis and produce chlorine when energized with DC current. Chlorine
is generated as pool water containing salt passes through the cell. The chlorine
production can be varied by either adjusting the Chlorine Production Level on the
power center or by varying the number of hours the PureLink is on each day. The
PureLink automatically cleans the Cell electrodes once every 3 hours by reversing
polarity. This does not interrupt the production of Chlorine.
Flow/Salinity/Temperature Sensor The Flow/Temp/Salinity Sensor only allows the Cell to operate if
thereisadequatewaterowthroughtheCell.ThesalinityportionoftheFlow/Temp/
Salinity Sensor detects the level of salt in the pool water. This salt level is displayed
in grams per liter (gpl) on the Liquid Crystal Display (LCD) whenever the salinity
button is pressed. This eliminates the need for manual pool water salinity testing.
Pool Temperature is now available on all models by pressing the Temperature button.
2.2 ElectricalSpecications
Circuit Protection 2 pole 20 AMP device at the Electrical Panel.
Model AP700 Model AP1400
Input: 115 VAC, 50/60 Hz, 1.5 AMPS
230 VAC, 50/60 Hz, 0.75 AMPS
Input: 115 VAC, 50/60 Hz, 2.5 AMPS
230 VAC, 50/60 Hz, 1.25 AMPS
Output: 22-30 VDC @ 3 AMPS maximum Output: 22-30 VDC @ 6 AMPS maximum
Chlorine: 0.625 lb. / 24 Hr. (283 gm / 24 Hr.) Chlorine: 1.25 lb. / 24 Hr. (567 gm / 24 Hr.)
External
Control:
ORP/External Control Connector
AquaLink®RS485 Connector
External
Control:
ORP/External Control Connector
AquaLink®RS485 Connector
CAUTION
Factory wired for 230 VAC service. If available electrical service is 115 VAC, the power supply
wiring must be changed to operate on 115 VAC as shown in Figure 2b.
The PureLink is powered from the LOAD SIDE of the pool circulation pump relay; therefore, if the
available electrical service is 115 VAC, then the pump must also be wired for 115 VAC.
Page 9
Figure 2a. 230 VAC Wiring Diagram for the AquaLink RS PureLink System
Filter Pump Relay Aux. 3 Relay
Load 2
Line 2
Load 1
Line 1
Wire Nut to
120 VAC Power
Low voltage raceway (do not run high voltage in this compartment)
Breakers
Ground
Neutral
Blower
(120 VAC)
Filter Pump
(240 VAC)
PRIMARY
24 VAC
SECONDARY
VAC
Primary
Secondary
A B
PureLink
Back PCB
Ribbon Cable from
Front PCB
To PureLink
Cell
Test
Switches
4321
RED
BLK
YEL
GRN
AquaLink RS ORP
24 VAC
Flow Salinity
Sensor
Ribbon Cable
to Back PCB
PureLink
Front PCB
Front PCB Shown removed from the Power
Center. Front PCB Located in front of Back PCB
and behind AquaLink RS PCB
(Middle Primary Wires Not Used)
Wiring Harness to PureLink Cell
DC Cord (22-30 VDC)
Green
Black/White
Multiplex Board
(J1 through J4)
J1J2J3J4
Page 10
Figure 2b. 115 VAC Wiring Diagram for the AquaLink RS PureLink System
Filter Pump Relay Aux. 3 Relay
Load 2
Line 2
Load 1
Line 1
Wire Nut to
120 VAC Power
Low voltage raceway (do not run high voltage in this compartment)
Breakers
Ground
Neutral
Blower
(120 VAC)
Filter Pump
(115 VAC)
PRIMARY
24 VAC
SECONDARY
VAC
Primary
Secondary
A B
PureLink
Back PCB
Ribbon Cable from
Front PCB
To PureLink
Cell
Test
Switches
4321
RED
BLK
YEL
GRN
AquaLink RS ORP
24 VAC
Flow Salinity
Sensor
Ribbon Cable
to Back PCB
PureLink
Front PCB
Front PCB Shown removed from the Power
Center. Front PCB Located in front of Back PCB
and behind AquaLink RS PCB
Wired to Neutral Bar
Wiring Harness to PureLink Cell
DC Cord (22-30 VDC)
Green
Black/White
Multiplex Board
(J1 through J4)
J1J2J3J4
Blk/Wht
Blk/Yel Blk/Red
Blk
Table des matières
Autres manuels Jandy Système de filtration d'eau
Jandy
Jandy APUREM Manuel utilisateur
Jandy
Jandy AquaPure Manuel utilisateur
Jandy
Jandy AquaPure Manuel utilisateur
Jandy
Jandy AquaPure Ei Series Manuel utilisateur
Jandy
Jandy SFTM22-1.5 Manuel du propriétaire
Jandy
Jandy CV Versa-Plumb Series Manuel utilisateur
Jandy
Jandy JEF-IN Manuel utilisateur
Jandy
Jandy CL Versa-Plumb Manuel utilisateur
Jandy
Jandy SFTM PRO Series Manuel utilisateur
Jandy
Jandy AquaPure APURE700 Manuel utilisateur
Jandy
Jandy JSWC40 Manuel utilisateur
Jandy
Jandy APURE35PLG Manuel utilisateur
Jandy
Jandy CJ200 Manuel du propriétaire
Jandy
Jandy SFSM60 Manuel utilisateur
Jandy
Jandy SFSM60 Manuel utilisateur
Jandy
Jandy JUVMP120 Manuel utilisateur
Jandy
Jandy AquaPure Pure700 Manuel utilisateur
Jandy
Jandy CL Versa-Plumb Series Manuel utilisateur
Jandy
Jandy Jandy Pro Series Manuel utilisateur
Jandy
Jandy TruGuard Manuel utilisateur
Manuels Système de filtration d'eau populaires d'autres marques
Wisy
Wisy LineAir 100 Manuel utilisateur
Schaffner
Schaffner Ecosine FN3446 Series Manuel d'utilisation
Pentair
Pentair FLECK 4600 SXT Guide de l'utilisateur
H2O International
H2O International H20-500 Manuel utilisateur
Renkforce
Renkforce 2306241 Manuel utilisateur
Neo-Pure
Neo-Pure TL3-A502 Manuel utilisateur
