JABSCO 60000 Series Manuel utilisateur

Model 60000-0000

60000-0024

Model 60000-Series

WIRELESS REMOTE CONTROL

FEATURES

•Adds wireless control to existing searchlight installa-

tions for both console and remote control operation.

•Can be installed for wireless-only operation.

•12/24 volt operation (60000-0000/60000-0024).

•True 8-way directional control with instant response for

precise targeting.

•“On/off”and“spot/flood”selection (for applicable models)

plus LED battery check.

•Long life lithium battery for hand-held remote control.

•Meets all applicable regulatory requirements for FCC,

Industry Canada, Australian and European compliance.

•“First-on” learning mode syncs transmitter and receiver

codes for no cross-talking with other remote control

devices.

•Up to four wireless remote units can be used per light

•Power saving "sleep mode" when not in use.

SPECIFICATIONS

Transmitter: 3VDC (CR2032 Battery)

Reverse polarity protected

433.92MHz transmitting frequency

Receiver: 12VDC or 24VDC

10 amp or 5 amp AGC Quick Blow Fuse

Input power short circuit protection

Range: 100 Ft. (30 Meters)

Temperature

Range: (-30°C to 70°C)

Regulatory

Compliance: FCC, Australia, Industry Canada and

Europe (For Radiated Emissions)

INSTALLATION

The Jabsco 60000-0000/0024 Remote adds wireless

control to new or existing Jabsco searchlight installa-

tions. It works in conjunction with a standard hard wired

Jabsco panel mount controller, thereby adding a second

controller for wireless remote operation of the search-

light at a distance of up to 100' (30 Meters). In applica-

tions where a panel mounted controller is not desired,

the 60000-0000/0024 Wireless Remote Control System

can be set up for wireless-only operation.

The Jabsco wireless receiver is installed inline between

the searchlight and the hard wired panel controller. (see

Fig. 1, 2). For installations where wireless-only operation

is preferred, the receiver's (female) connector cable is

connected to the searchlight cable.The receiver's (male)

connector cable is not connected in this instance. In

installations where the wireless remote will be used as a

second controller, (in addition to the hard wired panel

controller), the receiver's (male) connector cable is con-

nected directly to the the back of the panel controller or

to the wire pigtail coming from the back of the panel controller.

Full 8-way

Control Pad

On/Off; Spot/Flood

Switching

Grip Strip

LED Signal Transmission

Indicator (Battery Check)

WARNING

Disconnect battery before proceeding. Connecting

cables to the wireless receiver with power "on" to

the receiver can damage the unit.

Do not cut or trim the black receiver antenna wire

(so marked) nor connect it to battery ground (-).

CAUTION

Do not immerse the hand-held wireless fob in water.

CAUTION

Long Life Lithium Battery

Transmitter Cable Connectors

In instances where the pigtail from the panel controller is

not terminated with a Molex connector for connection

directly to the receiver cable, use the butt connectors

supplied to make wire to wire connections between the

controller panel and the receiver. See Fig.1, 2 below for

the wire to wire color coding. Note that the blue wire

from the receiver will, for example, connect to the blue

wire from the panel controller pigtail, the yellow to yellow, etc.

JABSCO WIRELESS RECEIVER

CONTROLLER & LIGHT CABLE WIRE COLOR CODING

Black to Controller

Brown to Controller

Green to Light

Green to Controller

Blue to Controller

Yellow to Light

Yellow to Controller

(+) Power to Battery

Black to Light

Brown to Light

Orange to Light

Orange to Controller

Blue to Light

Not Used

(-) Ground to Battery

Mount the receiver in a suitable location using the two

screws supplied.

LEARNING MODE PROCEDURE

Note: The transmitter included with this product was ini-

tialized at the factory. It is not necessary to conduct this

procedure unless adding or replacing a transmitter.

Disconnect battery power to the receiver. Press and

hold the “on/off” transmitter button while reconnecting

power to the receiver. The searchlight will turn “on” with-

in (2) seconds. Code synchronization is complete.

The Jabsco Wireless Remote Control Sytem can sup-

port (4) separate transmitters. Each time a transmitter is

added to the system or is replaced, all transmitters

require re-initialization using the above procedure.

Power to the receiver must be disconnected then recon-

nected while pressing the transmitter’s “on/off” button for

each transmitter added in turn.

Panel

Controller Wireless

Receiver 135

Searchlight

To Wired

Controller To

Searchlight

Black to Controller

Brown to Controller

Green to Light

Green to Controller

Blue to Controller

Yellow to Light

Yellow to Controller

(+) Power to Battery

Black to Light

Brown to Light

Orange to Light

Orange to Controller

Blue to Light

Gray to Light

Gray to Controller

(-) Ground to Battery

Panel

Controller Wireless

Receiver 5”

Searchlight

Fig. 2 (Lights with 43670-1003 Controller)

Fig. 1 (Lights with 60020-0000 Controller)

PARTS LIST

Part

KeyDescription Qty. Number

1 Wireless Reciever 1 1000616-01K

2 Receiver Cable Assembly 1 1000617-01K

3 Wireless Transmitter 1 1000618-01K

4 Lanyard 1 1000626-01K

OPERATING INSTRUCTIONS

With the wireless receiver installed and connected to the

searchlight cable and to the panel mounted controller (if

used), follow the following procedure.

Connect battery power to the receiver, searchlight and

hard wired panel mounted controller (if installed).

Press and hold the “on/off” button on the wireless tran-

mitter for approximately (1) second. The searchlight will

turn “on”.

Note: The red LED Signal Transmission Indicator should

be blinking while the button is depressed. If not, replace

the transmitter battery, accessed by removing the (4)

screws on the rear of the case.

With the light “on”, switching from spot to flood beam (for

5” chrome/stainless and older 7” chrome models), is

accomplished by pressing and releasing the “on/off” but-

ton quickly with no hold time. To turn the light “off”, press

and hold the “on/off” button for (1) second or until the

searchlight turns “off”.

The Jabsco 60000-0000/0024 Wireless Remote Control

features a true 8-way directional touch pad. The light’s

movement can be directed in the horizontal and vertical

simultaneously for quicker times-to-target. Searchlight

movement is instantaneous with no rotation “run-by”

when the pad is released. This provides precise pointing

control.

The wired panel controller and the wireless transmitter

share command of the light equally. Command input

from either will be executed by the searchlight.

Note: In cases when the 43670-1003 Controller toggle

switch is set to “F” for “flood” or “S” for “spot”, the beam

can still be switched using the wireless transmitter. The

wireless transmitter command will then override the

43670-1003 switch setting. In this instance the toggle

switch will indicate a flood beam, for example, when the

light is actually in spot mode, having been switched to

“spot” using the wireless transmitter. Control is returned

to the wired controller with any movement of its joystick.

The searchlight beam angle will then change to match

that indicated by the toggle switch.

When the searchlight has been turned “on” using the-

hard wired panel controller’s “on/off”toggle switch, the-

light can be turned “off”using the wireless transmitter

without the need to return to the helm station to deacti-

vate the light. Although the toggle switch then indicates

“on”, the searchlight will be “off”. With any movment of

the wired controller’s joystick the light will turn “on” and

the beam angle (spot vs.flood) will be as indicated by

the toggle switch.

CIRCUIT PROTECTION

An AGC 10 amp (for 12VDC) or 5 amp (for 24VDC) quick

blow fuse is included with the wireless receiver cable

assembly. In the event that it should be necessary to

replace the fuse, the inline fuse holder is located on the

receiver’s power lead.

1234

FCC GUIDELINES

This device complies with part 15 of the FCC Rules.

(1)This device may not cause harmful interference.

(2) This device must accept any interference received,

including interference that may cause undesired opera-

tion.

Section 15.105 Information to the user Note:This

equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference

in a residential installation. This equipment generates,

uses and can radiate radio frequencey energy and, if

not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this

equipment does causes harmful interference to radio or

television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the fol-

lowing measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and

receiver.

3. Connect the equipment into an outlet on a circuit dif

ferent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV

technician for help.

ITT Marine and Leisure declares that this device is in

compliance with the essential requirements and

adheres to relevant provisions of Directive 1999/5/EC.

A. LIMITED WARRANTY:

Jabsco warrants that at the time of shipment, the products

manufactured by Jabsco and sold hereunder shall be in

conformity with applicable written specifications and descriptions

referred to or set forth herein, free from defects in material and

workmanship, merchantable, and suitable for a particular

purpose, provided such is implied by State law under the

circumstances of this sale.

B. WARRANTY ADJUSTMENT:

1. Jabsco agrees to repair or furnish a replacement for, but not to

remove or install, any product or component thereof which, within

one (1) year from date of purchase, shall upon test and

examination by Jabsco prove defective within the above warranty.

Receipt verifying purchase date is required to obtain adjustment.

2. Buyer shall notify Jabsco of any defect within this warranty no

later than ninety (90) days after the defect is discovered.

3. No product will be accepted for return or replacement without the

prior written authorization of Jabsco. Upon such authorization,

and in accordance with instructions from Jabsco, the product will

be returned to Jabsco, shipping charges prepaid by Buyer.

Products returned to Jabsco will be addressed as follows:

JABSCO

Cape Ann Industrial Park

Gloucester, MA 01930

Or to such alternate locations as may be designated

on the product, its container, or this sheet.

Repair or replacement made under this warranty

will be shipped prepaid to Buyer.

C. EXCLUSIONS FROM WARRANTY AND

LIMITATION OF LIABILITY:

1. The foregoing warranty is limited solely as set forth herein and

applies only for the period designated above.

2. ITT SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE,

SPECIAL OR CONSEQUENTIAL DAMAGE OF ANY KIND,

WHETHER BASED UPON WARRANTY, CONTRACT,

NEGLIGENCE, OR STRICT LIABILITY ARISING IN

CONNECTION WITH THE SALE, USE, OR REPAIR OF THE

PRODUCT.

3. THE MAXIMUM LIABILITY OF ITT IN CONNECTION WITH THIS

WARRANTY SHALL NOT IN ANY CASE EXCEED THE

CONTRACT PRICE FOR THE PRODUCT CLAIMED TO BE

DEFECTIVE OR UNSUITABLE.

4. This warranty does not extend to any product manufactured by

Jabsco which has been subjected to misuse, neglect, accident,

improper installation, or use in violation of instructions furnished

by Jabsco.

5. This warranty does not extend to or apply to any unit which has

been repaired or altered at any place other than Jabsco’s factory,

or by persons not expressly approved by Jabsco, nor to any unit

the serial number, model number, or identification of which has

been removed, defaced or changed.

6. Components manufactured by any supplier other than Jabsco

shall bear only that warranty made by the manufacturer of that

product.

7. This warranty applies to products defined as“consumer products”

by the Consumer Product Warranties Act as from time to time

amended.

D. CONSUMER RIGHTS:

This warranty gives you specific legal rights, and you may have

other rights which vary from state to state. Some states do not

allow exclusion or limitation of damages.

STANDARD WARRANTY:If the products manufactured and sold

hereunder are not Consumer Products, the warranty extended to

Buyer shall be as set forth in subparagraphs (A), (B), and (C), EXCEPT

THAT ALL EXPRESS OR IMPLIED WARRANTIES OR

MERCHANTABILITY OR SUITABILITY FOR ANY PARTICULAR

PURPOSE ARE EXCLUDED.

ONE YEAR LIMITED WARRANTY

Jabsco

Bingley Road, Hoddesdon

Hertfordshire EN11 OBU

Tel: +44 (0) 1992 450145

Fax: +44 (0) 1992 467132

CANADA

Fluid Products Canada

55 Royal Road

Guelph, Ontario N1H 1T1

Tel: 519 821 1900

Fax: 519 821 2569

JAPAN

NHK Jabsco Company Ltd.

3-21-10, Shin-Yokohama

Kohoku-Ku,Yokohama, 222

Tel: 045 475 8906

Fax: 045 475 8908

USA

Jabsco

1 Kondelin Road

Gloucester, MA 01930

Tel: 978 281 0440

Fax: 978 281 2619

GERMANY

Jabsco GmbH

Oststrasse 28

22840 Norderstedt

Tel: +49-40-53 43 73 -0

Fax: +49-40-53 53 73 -11

ITALY

Jabsco Marine Italia S.r.l.,

ViaTomasseo, 6,

20059Vimercate, Milano

Tel: +39 039 6852323

Fax: +39 039 666307

Warranty: All products of the company are sole and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request.

The information provided herein is for guidance only, it does not constitute a guarantee of performance or specification of any individual product or component.

www.jabsco.com

Ce manuel convient aux modèles suivants

Autres manuels JABSCO Télécommande