Jabra Pro 92 Series Guide d'installation
FAQ - All questions
Setup for Desk Phones
How do I connect my Jabra Pro 92x with Cisco 7942G, 7945G, 7962G, 7965G, 7975G?
Prerequisites:
Jabra Pro 92x + Jabra Link 14201-16
In combination with one of the following phones:
Cisco 7942G
Cisco 7945G
Cisco 7962G
Cisco 7965G
Cisco 7975G
Important:
If you are connecting the Jabra Pro 925 wireless headset to a Cisco desk phone infrastructure that
uses LAN switches, while also using the included Jabra USB cable between the base and a
computer, then we recommend that you use the latest version of the Jabra Link 14201-43
(marked B) instead of the Jabra Link 14201-16 EHS cable. This will ensure the stable use of the
Cisco desk phone.
System:
Cisco Unified Call Manager (CUCM)
Cisco Call Manager Express (CME) from version 4.1, and phone firmware 8.3.3. When
downloading from Cisco, the required IOC version will be marked.
To use remote call control, the following prerequisites must be met :
Voip-phones SCCP (Cisco protocols) require: phone firmware 8.3(3), and the Cisco
Unified Communications Manager (CUCM) from release 3.3, 4.0, 4.1, 4.2, 4.3, 5.0, 6.0,
7.0, and 8.0.
SIP phones require: phone firmware 8.3(3), and the Cisco Unified Communications
Manager (CUCM) from release 5.0, 5.1, 6.0, 7.0, and 8.0.
Remote call control is also possible in combination with the expansion modules 7915 and 7916.
Connection:
1. Take the supplied RJ10 to RJ10 connection cable and insert one end in the headset
interface of the Cisco phone, and the other end in the socket marked with the phone icon
on the Jabra Pro 92x.
2. Connect the EHS adapter to the AUX socket of the Cisco phone and to the AUX interface
of the base.
Now you can set up the headset for your phone using the automatic configuration or manually.
Automatic configuration:
To start the automatic configuration, have someone call you on the phone and wait at least 10
seconds before you answer. Now the appropriate EHS mode should be set up.
If the automatic configuration did not work, manually select the DHSG mode. See the user
manual for the headset for more information.
Base setup:
Set the dial tone switch to position "B".
Microphone volume setup:
Put on the headset and make a test call.
Now you can select the microphone volume using the +/-button.
Communication Manager setup:
Under Phones>Wireless Headset Hookswitch Control, enable answer/end for each terminal
phone.
Was this useful?
How do I connect my Jabra Wireless headset with the Jabra GN1000 Remote Handset Lifter
(RHL) to my standard desk phone so I have remote call control using my headset?
Connection:
1. Connect the AC adapter (supplied with the headset) to the headset base, and connect the
other end to an electrical outlet.
2. Disconnect the phone handset from the phone base, and then connect it to the socket that
is marked with a handset icon on the headset base.
3. Connect the modular connector (supplied with the headset) to the headset interface on
your desk phone, and connect the end with the blue band to the headset base socket that is
marked with a phone icon.
4. Connect the attached cable of the GN1000 RHL to the AUX interface on the headset
base.
5. Mount the GN1000 RHL onto the handset cradle of the desk phone using the provided
adhesive.
6. Rest the desk phone handset on the GN1000 RHL arm and ensure that it presses the desk
phone hook switch.
Configuration:
1. Follow the setup instructions for your Jabra wireless headset. If the headset base requires
manual configuration, set the Electronic Hook Switch setting to "RHL" and set the dial
tone switch to position “A”.
2. Make a call to the headset. If the volume of your voice is too loud or quiet to the person
you are calling, adjust the headset microphone volume until you achieve the optimum
level.
Was this useful?
How do I connect my Jabra wireless headset with the Jabra Link 14201-10 to my Aastra desk
phone so I have remote call control using my headset?
Prerequisites
Jabra Link 14201-10
DHSG connection cable from Aastra
Connection:
3. Connect the AC adapter that is supplied with the headset to the headset base, and connect
the other end to an electrical outlet.
4. Connect the Jabra Link 14201-10 EHS cable with the red band to the AUX
interface on the headset base, and connect the end with the blue band to the
headset base socket that is marked with a phone icon.
5. Connect the Jabra Link 14201-10 EHS cable single end to the RJ45 adapter that is
supplied with your Aastra DHSG Cable Kit.
6. Connect the Aastra DHSG Cable Kit cord with the blue band to the RJ45 adapter.
Connect the Aastra DHSG Cable Kit cord with the green band to the headset
interface on the Aastra desk phone, and connect the end with the yellow band to
the socket for the Aastra phone expansion module.
Configuration:
7. Ensure the Audio Mode is set to “Headset/Speaker”, and the DHSG mode is enabled on
your desk phone. Refer to your phone or IT support for assistance.
8. Follow the setup instructions for your Jabra wireless headset. If the headset base
requires manual configuration, set the Electronic Hook Switch setting to “DHSG”
and set the dial tone switch to position “A”.
9. Make a call to the headset. If the volume of your voice is too loud or quiet to the
person you are calling, adjust the headset microphone volume until you achieve
the optimum level.
Was this useful?
How do I connect my Jabra wireless headset with the Jabra Link 14201-10 to my desk phone so I
have remote call control using my headset?
Connection:
1. Connect the AC adapter that is supplied with the headset to the headset base, and connect
the other end to an electrical outlet.
2. Connect the Jabra Link 14201-10 EHS cable with the red band to the AUX interface on
the headset base, and connect the end with the blue band to the headset base socket that is
marked with a phone icon.
3. Connect the Jabra Link 14201-10 EHS cable single end to the headset interface on the
desk phone.
Configuration:
1. Ensure the headset function is enabled on the desk phone. Refer to your phone or IT
support for assistance.
2. Follow the setup instructions for your Jabra wireless headset. If the headset base requires
manual configuration, set the Electronic Hook Switch setting to “DHSG” and set the dial
tone switch to position “A”.
3. Make a call to the headset. If the volume of your voice is too loud or quiet to the person
you are calling, adjust the headset microphone volume until you achieve the optimum
level.
Was this useful?
How do I connect my Jabra wireless headset with the Jabra Link 14201-17 to my Polycom desk
phone so I have remote call control using my headset?
Connection:
1. Connect the AC adapter (supplied with the headset) to the headset base, and connect the
other end to an electrical outlet.
2. Connect the modular connector (supplied with the headset) to the headset interface on
your Polycom phone, and connect the end with the blue band to the headset base socket
that is marked with a phone icon.
3. Connect the Jabra Link 14201-17 EHS cable with the red band to the AUX interface on
the headset base, and connect the other end to the AUX interface on the Polycom phone.
Configuration:
1. Ensure the “Headset Hook Switch” function on the desk phone is set to “Jabra EHS”.
Refer to your phone or IT support for assistance.
2. Follow the setup instructions for your Jabra wireless headset. If the headset base requires
manual configuration, set the Electronic Hook Switch setting to “DHSG” and set the dial
tone switch to position “A”.
3. Make a call to the headset. If the volume of your voice is too loud or quiet to the person
you are calling, adjust the headset microphone volume until you achieve the optimum
level.
Was this useful?
How do I connect my Jabra wireless headset with the Jabra Link 14201-33 to my Avaya desk
phone so I have remote call control using my headset?
Connection:
1. Connect the AC adapter that is supplied with the headset to the headset base, and connect
the other end to an electrical outlet.
2. Connect the Jabra Link 14201-33 EHS cable with the red band to the AUX interface on
the headset base, and connect the end with the blue band to the headset base socket that is
marked with a phone icon.
3. Connect the single end of the Jabra Link 14201-33 EHS cable to the headset interface on
the Avaya desk phone.
Configuration:
1. Ensure the headset function on the desk phone is enabled. Refer to your phone or IT
support for assistance.
2. Follow the setup instructions for your Jabra wireless headset. If the headset base requires
manual configuration, set the Electronic Hook Switch setting to “DHSG” and set the dial
tone switch to position “A”.
3. Make a call to the headset. If the volume of your voice is too loud or quiet to the person
you are calling, adjust the headset microphone volume until you achieve the optimum
level.
Was this useful?
How do I connect my Jabra wireless headset with the Jabra Link 14201-43 to my Cisco desk
phone so I have remote call control using my headset?
Connection:
1. Connect the AC adapter (supplied with the headset) to the headset base, and connect the
other end to an electrical outlet.
2. Connect the modular connector (supplied with the headset) to the headset interface on
your Cisco phone, and connect the end with the blue band to the headset base socket that
is marked with a phone icon.
3. Connect the Jabra Link 14201-43 EHS cable with the red band to the AUX interface on
the headset base, and connect the other end to the AUX interface on the Cisco phone.
Important:
If you are connecting the Jabra Engage, Jabra Pro 9400, Jabra Pro 925, Jabra Motion Office, or
Jabra Go 6470 wireless headset to a Cisco desk phone infrastructure that uses LAN switches,
while also using the included Jabra USB cable between the base and a computer, then we
recommend that you use the latest version of the Jabra Link 14201-43 (marked B) instead of the
Jabra Link 14201-43 EHS cable (marked A) to ensure the stable use of the Cisco desk phone.
Configuration:
1. Ensure the Headset Hook Switch Control function is enabled on the desk phone. Refer to
your phone or IT support for assistance.
2. Follow the setup instructions for your Jabra wireless headset. If the headset base requires
manual configuration, set the Electronic Hook Switch setting to “IQ” and set the dial tone
switch to position “B”.
Ce manuel convient aux modèles suivants
1
Autres manuels Jabra casque
Jabra
Jabra BT530 - TECHNISCHE DATEN Manuel utilisateur
Jabra
Jabra GN 5330 Office Manuel utilisateur
Jabra
Jabra BT4010 Manuel utilisateur
Jabra
Jabra 6430-17-20-205 - GO 6430 - Headset Manuel utilisateur
Jabra
Jabra SUPREME Manuel utilisateur
Jabra
Jabra GN9120 Flex Manuel utilisateur
Jabra
Jabra SPORT Manuel utilisateur
Jabra
Jabra BT 125 Manuel utilisateur
Jabra
Jabra JX10 - MANUAL 2 Manuel utilisateur
Jabra
Jabra Pro 9460 Mono Manuel utilisateur
Jabra
Jabra MINI Fiche technique
Jabra
Jabra GN 6210 Mode d'emploi
Jabra
Jabra SUPREME UC Manuel utilisateur
Jabra
Jabra CLIPPER Guide de référence
Jabra
Jabra GN2100 Manuel utilisateur
Jabra
Jabra BT150 - Headset - Over-the-ear Manuel utilisateur
Jabra
Jabra WAVE Guide de référence
Jabra
Jabra BT5010 Multiuse Manuel utilisateur
Jabra
Jabra Engage 65 Manuel utilisateur
Jabra
Jabra Elite 25e Fiche technique
