J-Alert JA-2030 Manuel utilisateur
Operators Manual
Model JA-2030
April 2012 Ver 1.4
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 1
INDEX
Overview ……..………………………………………………. 2
Theory of operation ...…………………………………… 3
Front Panel controls …………………………………….. 5
Rear Panel connections ………………………………… 7
Installation and Operation ..…………………………. 8
Support & Service ………………………………………… 17
Warranty ………………………………………………………. 18
Examples of Jamming Devices ……………………. 20
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 2
Jammer Detector
Models JA-2030
OVERVIEW
The J-Alert is multi-band receiver capable of detecting
Radio Frequency Jamming. The J-Alert uses signal
analysis to identify valid communications and
differentiate them from malicious Radio Frequency
Jamming signals.
When Jamming is detected, visual alerting of the
jammed radio spectrum is identified on the front of the
unit and the RSSI (received signal strength indication)
LED’s on the front display are activated as well as an
audible beep will also be heard. The LED activity will
indicate target vehicle position relative to the J-Alert
equipped vehicle.
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 3
Theory of Operation
The J-Alert contains a number of sensitive radio frequency
receivers tuned to specific radio bands.
Model JA-2030 (Europe & Brazil)
GPS – L1
GSM /900 – GSM/1800 MHz
UMTS
These radio receivers are tuned to the Downlink (Site)
frequencies of their respective cellular bands. Very fast scanning
within the bands is used with an adaptive signal analysis to
identify jamming signals from legitimate radio signals. When
jamming is detected the receiver identifying the jammed signal
will indicate band jamming on the front panel illuminating the
respective led’s.
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 4
(BAND JAMMING LED INDICATORS)
Cell Jamming
When cellular jamming is detected on any of the cellular bands,
the Cell LED will illuminate. RSSI LED indication will be displayed
indicating the strength of the Cellular Jammer received signal.
GPS Jamming
When jamming of the GPS L-1 frequency is detected, the GPS
LED will illuminate and tracking using the RSSI LED display is
active.
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 5
Front Panel
(RSSI LED’S)
Front Panel Controls
Ext/Off/Bat : 3 position power switch
Ext – power is provided via usb plug on the back of the
unit 5vdc direct or a 12v to 5v Cigarette lighter/convertor
plug
Off – Unit is turned off.
Bat – Internal 5v Li-polymer rechargeable battery is used.
JA-2030 will operate for approximately 2 hours.
Charging of the internal battery occurs when the external
power is connected.
PWR: Red LED illuminates when J-Alert is turned on and power
is supplied.
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 6
Cell: Yellow led illuminates when Jamming is indicated
on at least one of the Cellular frequency Bands.
GPS: Yellow led illuminates when Jamming is indicated
on the GPS L1 frequency.
Signal Strength/RSSI
6 LED display that will indicate the RSSI of the GPS
L1 or Cellular frequency that is being jammed.
Used for tracking the jammer.
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 7
Rear Panel
Rear Panel Connections
Relay Out 2.5mm Stereo jack providing a 3 wire N/O N/C dry
contacts for remote triggering of external devices.
On valid alarm sense the relay will activate and
latch for 10 sec.
Antennas SMA whip antenna
USB Supply USB connection for external power input 5v dc.
JA-2030
___________________________________________________________
This document contains designs and other information which are the property of Dyplex
Communications Limited. Except for rights expressly granted by contract, this document may not,
in whole or in part, be duplicated, disclosed or used without the prior written permission of Dyplex
Communications Limited. pg. 8
Installation and Operation
Package Contains
1- J-Alert Model JA2030 (EU & BR)
1- DC to DC convertor 12/24 to 5 v dc.
1- 220v AC to 5 v dc adaptor
1- Whip antenna
4- Pieces of 3M Dual Lock adhesive strips for unit mounting
1) Install J-Alert Model JA-2030 in a dry location either at a fixed
location or inside a vehicle to suit the requirements of your
operation. Antenna location should be at a line of level to
intercept signals from the suspect vehicle either at Dashboard or
Sun Visor level. Numerous configurations of equipment in
vehicles pre-exist therefore ensure antennas are located above
dashboard height and the device is secured to the vehicle in a
manner to prevent movement during driving maneuvers 4 strips
of 3M Dual Lock recloseable tape are provided, 2 for the J-Alert
and 2 for the surface to be attached to in the vehicle. The JA-
2030 is a small and light weight device allowing for the
application of double sided tape or Velcro for the purpose of
mounting the unit within the vehicle and this method also
Table des matières
