ITW Dynatec DY 2008 Manuel utilisateur

DY 2008

Pattern Controller

CONTROLLER

Operating Manual

2008 D.BOO 11/02

ITW Dynatec

An Illinois Tool Works Company

31 Volunteer Drive

Hendersonville, TN 37075 USA

Telephone +1 615 824 3634

FAX +1 615 264 5222

dynatec@itwdynatec.com

www.itwdynatec.com

ITW Dynatec K.K.

Daiwashinagawa Bldg., 7-15 Konan, 3-Chome

Minata-Ku, Tokyo 108 Japan

Telephone 81 3 3450 5901

FAX 81 3 3450 8405

info@itwdynatec.co.jp

ITW Dynatec

Industriestraße 28

40822 Mettmann, Germany

Tel.: +49 (0)2104 915-0

FAX: +49 (0)2104 / 915 111

info@itwdynatec.de

Manual #50-14

Rev.11/15

For an online copy of this manual, go to www.itwdynatec.com/manuals.htm

Manual #50-14 Revised 3/05

C. 2002 I

1: Safety Instructions 1 - 1...........................................

About this Manual 1 - 1...........................................................

Proper Use of System 1 - 1........................................................

Manual Symbols 1 - 1............................................................

Authorized Use of System 1 - 1....................................................

Installation, Maintenance, Repair or Disposal of the System 1 - 1.......................

Modification to the System 1 - 2....................................................

Working with Cover Open 1 - 2....................................................

2: Product Description 2 - 1..........................................

General 2-1....................................................................

Technical Data 2-2..............................................................

Dimensions (Basic version) 2 - 4...................................................

Operating and Connecting Elements (Basic version) 2 - 4.............................

3: Installation 3 - 1..................................................

Connectors and Pin Definitions 3 - 1................................................

Connecting the System 3 - 2......................................................

Locating an Optical Trigger (Sensor) 3 - 2...........................................

Connecting Optional Accessories 3 - 3..............................................

4: Operating 4 - 1...................................................

Operator’s Panel 4 - 1............................................................

Remote Purge Control 4 - 2.......................................................

Service Settings Menus 4 - 3......................................................

Production Setup Menu 4 - 4......................................................

Power On and Software Version 4 - 5...............................................

Service Settings 4-6.............................................................

Service Settings Menu 1 of 3 Overview 4 - 6..............................................

Service Settings Menu 2 of 3 Overview 4 - 8..............................................

Service Settings Menu 3 of 3 Overview 4 - 9..............................................

Factory Defaults 4-9..................................................................

Service Setting Programming Conventions 4 - 11.....................................

Display Contrast Adjustments 4 - 11.................................................

Service Settings Menu 1 4 - 12.....................................................

Select Language 4-12..................................................................

Load Program 4-13....................................................................

Trigger Assignment 4-14................................................................

Trigger Lock 4-15......................................................................

Encoder--Channel Assignment 4 - 15......................................................

Encoder Scaling (Encoder Type and Unit) 4 - 17............................................

Min/Max Speed Configuration 4 - 18.......................................................

Channel Mode Adjustment 4 - 19.........................................................

Change Security Lock 4 - 22.............................................................

Change Access Code 4 - 22.............................................................

Service Settings Menu 2 4 - 23.....................................................

Trigger Setup 4-23.....................................................................

Pressure Signaling 4-24................................................................

Pressure Assignment 4-25..............................................................

Pressure Curve Configuration 4 - 25.......................................................

Manual #50-14 Revised 1/09

C. 2002

Spike Voltage Adjustment 4 - 27..........................................................

Spike Duration Adjustment 4 - 28.........................................................

Shutter Assignment 4-29...............................................................

Shutter Dwell Timing Adjustment 4 - 30....................................................

Change Security Lock 4 - 31.............................................................

Change Access Code 4 - 31.............................................................

Service Settings Menu 3 4 - 32.....................................................

STOP Configuration 4-32...............................................................

PC--Communication (Option) 4 - 33.......................................................

Change Profibus Address (Option) 4 - 33..................................................

Shutter Trigger Setup 4-34..............................................................

Digital Configuration 4-35...............................................................

Load Factory Defaults 4 - 37.............................................................

Change Security Lock 4 - 39.............................................................

Change Access Code 4 - 39.............................................................

Production Setup 4 - 40............................................................

Stop Function 4-41....................................................................

Glue Pattern Setup 4-42................................................................

Copy/ Paste Function 4-44..............................................................

Pressure Adjustment 4 - 45.........................................................

Adjust Minimum Pressure (2--Point Curve) 4 - 45............................................

Adjust Maximum Pressure (2--Point Curve) 4 - 45...........................................

Adjust Purge Pressure (2--Point Curve) 4 - 46..............................................

Assigning the Pressure Points to the Machine Speed (12--Point Curve) 4 - 46...................

Adjust Purge Pressure (12--Point Curve) 4 - 47.............................................

System Menus: Dot Function, Stitching and Head Position 4 - 48........................

Dot Configuration 4-48.................................................................

Stitching Configuration 4 - 50.............................................................

Offset (Head Position) 4 - 52.............................................................

Speed Compensation Adjustment 4 - 54.............................................

Manual Gluing (Purge) 4 - 55......................................................

5: Troubleshooting 5 - 1.............................................

Error Messages of the DY 2008 5 - 1...............................................

Communication Error 5-1..............................................................

Over Current Failure 5-1...............................................................

Compensation Error 5-1...............................................................

Appendix A

Common Accessories App. A 1........................................................

Appendix B

Printed Circuit Boards and Wiring Information App. B 1...................................

Appendix C

Programming Log App. C 1...........................................................

Manual #50-14 Revised 1/03

1-1

C. 1998

Safety Instructions

Authorized Use of System

Only authorized persons who have read and understood the instruction manual or who

have been trained by ITW Dynatec may install, operate or dispose off this system.

Appropriate electrical safety procedures must be observed.

A copy of this manual should be kept with the installed system as reference material.

Proper Use of the System

This controller is designed for use only with ITW Dynatec hot melt or cold glue systems.

Other applications should be attempted only after consulting with ITW Dynatec.

Manual Symbols

Caution

This symbol means that failure to observe the specific instructions could

cause damage to the equipment.

Danger! High Voltage!

This symbol means there is a danger of electrical hazard.

Note! Provides useful information regarding the use of the system.

Manual #50-14 Revised 1/03

Safety Instructions

1-2 C. 1998

Modifications to the System

No modification can be made to the system without consulting ITW Dynatec. Use only

factory--recommended parts and fittings. ITW Dynatec does not assume any resonsibility

for damage which occurs as a result of using parts that are not factory recommended.

Working with the Cover Open

Never operate this controller with open cover. There are no servicable components inside.

All settings are done via Software.

Inside the controller are electric current--carrying components. To avoid personal injury, do

not touch them while input power is ON. Disconnect and lockout main power before opening

the cover. Then wait a few seconds until all electrical components have discharged.

Manual #50-14 Revised 1/03

2-1

C. 2002

Product Description

General

The DY 2008 Pattern Controller is one component of an adhesive application system

consisting of a hot-melt unit, cold glue pressure vessel or cold glue pump, adhesive hoses

and applicator heads. The controller can be used for hot--melt or cold glue application.

The pattern controller activates solenoids for four (Basic Version) up to 128 (Option)

applicator heads in order to create individual adhesive patterns. It is possible to program

up to 16 independent glue events (16 glue + 16 delay) per channel.

Each channel can operate in one of the possible modes: glue beads, dots, continuous

gluing, random product length and stitching.

Gluing can be triggered with a photo eye, proximity switch or by exceeding a certain

machine speed.

Every channel may be assigned to its own trigger input, if desired, to increase the accuracy

of multiple parallel running products.

In order to accelerate the timing of solenoids it is possible to apply initially a higher voltage

(Over--excitation). The voltage level and the duration time of this over--excitation is

programmable via software on a channel-by-channel basis. This enables applications for

hot--melt and cold glue.

The speed of the production machine will be registered with up to four encoders and

indicated on the display. It can be used to control the speed of one or more gear pumps of

adhesive supply units or to control the glue pressure on a cold glue system via I/P or U/P

transducers. Every time the machine speed varies the glue pressure will follow.

Working with four encoders enables application on machines with different speeds e.g.

Right--Angle machine.

The pressure vs. speed ramp can be linear or for better adaptation to production conditions

a 12--point curve is programmable.

A machine contact is available to enable or disable the controller. With this contact it is

possible to start and stop the gluing together with the parent machine.

The user can select whether the gluing stops immediately or continues.

The controller can provide an output signal to close a shutter devise (automatic tip sealer)

in order to prevent clogging of cold glue applicators from drying during production breaks.

If necessary this shutter output can be activated with a dedicated trigger input.

Alternatively the programming of the glue pattern can be done on a computer and

corresponding software. An optional RS232/485 or Profibus interface can be used to

communicate with the pattern controller from an external device.

Critical conditions can be signalled by means of two alarm outputs.

Manual 50-14 Revised 11/15

Product Description

2-2 C. 2002

Technical Data

General

Operating Temperature 0°Cto+50°C(32°F to122 °F)

Storage Temperature -- 1 0 °Cto50°C(32°F to122 °F)

Power Supply 1/N/PE 230 V 50--60 Hz

1/N/PE 115 V 50--60 Hz

1/N/PE 200 V 50--60 Hz

Power Consumption 180w (8 channel version)

Operating Languages German, English, Finnish, French, Italian

Number of Programs 60 stored in permanent memory

Protection Class IP 40

(Option IP 54)

CE Approval Granted yes

Trigger

Input connectors 24 V DC, max. 100 mA, NPN, PNP, Push--Pull

Max. Number 4 Master Triggers (Triggers #1 thru 4)

1 additional per channel (Channel #5 and above)

Assignment (every channel can be assigned to a Master

Trigger or its Channel Trigger and any trigger may be “Anded”

to a Master Trigger)

Every Trigger can be assigned to each of the channel

Via AND--Function multiple Triggers can be combined.

Trigger Lock 0--8000 mm (0.01 to 80.00 in)

Encoder

Max. Number 4

Input connectors X17 and X18 24 V DC, max. 100 mA, NPN (scalable)

Assignment Any encoder can be assigned to any channel.

Configuration Metric or inch

Scaling 1--4000 pulse/m

0.01--99.99 pulse/inch

Indication of Production Machine Speed max. 1200 m/min (2000 pulses/m)

4000 ft/min (50 pulses/inch)

Speed Configuration

Start Gluing above (Vmin START)0--999 m/min

0--999 ft/min

Stop Gluing below (V min STOP)0--999 m/min

0--999 ft/min

Maximum Machine Speed (V max) 0--1200 m/min

0--4000 ft/min

Output (Valve Output)

Channel X1 to X4 (Basic Version) for Controlling of Solenoids Valves (Short circuit proof)

Max. Number 4 (Option max. 128)

Output Voltage Nominal: 24 V DC

Overexcitation:

55 V (Factory Default) or 170 V

all Channels are individually adjustable

Overexcitation Timing 0.5--2.5 ms adjustable per software in steps of 0.5 ms

Wattage Capacity per Channel max. 20 W

Total Wattage Capacity for Channels 1--8 max. 160 W

Speed Compensation 0--999 mm

9.99 inch

Table des matières

Autres manuels ITW Dynatec Contrôleurs

ITW Dynatec

ITW Dynatec DPC2 Manuel d'utilisation

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur