Itm OSC-8 Manuel utilisateur
www.itmtools.com.au
Ver: 1.0
OPERATOR’S MANUAL
OSC-8 PENDULUM
WEAVE WELDER
PART NO. WA-OSC8
TO PREVENT SERIOUS INJURY OR DAMAGE TO YOUR PENDULUM WEAVE WELDER,
READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE
! !
The tools of innovation.
15335 E. Fremont Drive, Centennial, CO 80112
1–87STEELMAX, FAX 303–690–9172
www.steelmax.com sales@steelmax.com
OPERATOR’S MANUAL
O
OS
SC
C
8
8
PENDULUM OSCILLATOR
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
TABLE OF CONTENTS
Contents
1. GENERAL INFORMATION ............................................................................................... 3
1.1. Application ................................................................................................................. 3
1.2. Technical data............................................................................................................ 3
1.3. Equipment included ................................................................................................... 4
1.4. Dimensions ................................................................................................................ 5
2. SAFETY PRECAUTIONS.................................................................................................. 6
3. STARTUP AND OPERATION ........................................................................................... 7
3.1. Assembling ................................................................................................................ 7
3.2. Connecting................................................................................................................. 8
3.2.1. To the welding circuit....................................................................................... 8
3.2.1. To the power supply ........................................................................................ 9
3.2.2. To the Rail Runner 2 welding carriage............................................................10
3.3. Operating ..................................................................................................................12
4. ACCESSORIES ...............................................................................................................14
4.1. Freestanding support ................................................................................................14
4.2. Power supply ............................................................................................................15
5. EXPLODED VIEWS AND PARTS LIST............................................................................16
6. WIRING DIAGRAM ..........................................................................................................19
7. DECLARATION OF CONFORMITY .................................................................................20
8. WARRANTY CARD..........................................................................................................21
2www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
3
1. GENERAL INFORMATION
1.1. Application
The OSC 8pendulum oscillator is designed to oscillate MIG/MAG torches with the
diameter of 16–22 mm (5/8–7/8″). The oscillator is installed onto a 22 mm (7/8″)
diameter rod and powered from the welding equipment. Can be controlled manually
or by using an external START-STOP switch.
Using an optional freestanding support allows you to weld pipes that rotate and
plates that move. Using an optional power supply allows you to connect the oscillator
to a115 V or 230 V power source.
The oscillator can also be used on the Rail Runner 2 welding carriage to allow
work with or without seam tracking.
1.2. Technical data
Voltage
14–24 VDC
Power
50 W
Torch type
MIG/MAG
Torch diameter
16–22 mm (5/8–7/8″)
Oscillation type
Pendulum
Oscillation width at r=150 mm (6″)
1–30 mm (1–100%)
1/32–1-3/16″
Oscillation speed at oscillation width of 10 mm (3/8″) and
zero dwell time on ends
12–115 cycles/min (1–100%)
Oscillation dwell time on ends
0–3 s
Maximum torque
8 N·m (5.7 lb·ft)
Protection level
IP 21
Protection class
I
Required ambient temperature
0–50°C (32–122°F)
Weight
2 kg (4 lbs)
3
www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
4
1.3. Equipment included
1
Oscillator
1 unit
2
2 m (6.5 ft) power cord
1 unit
3
Low rod torch holder with clip
1 unit
4
Arm
1 unit
5
Clamping block
1 unit
6
M6x40 screw
2 units
7
80 mm (3″) rod
1 unit
8
5 mm hex wrench
1 unit
–
Operator’s Manual
1 unit
1
2
3
4
5
7
6
8
4www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
5
1.4. Dimensions
117 mm (4-5/8″)
215 mm (8-7/16″)
343 mm (13-1/2″)
5
www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
6
2. SAFETY PRECAUTIONS
1. Before use, read this Operator’s Manual and complete a training in occupational
safety and health.
2. Use only in applications specified in this Operator’s Manual.
3. Make sure that the oscillator has all parts and they are genuine and not damaged.
4. Make sure that the specifications of the power source are the same as those
specified on the rating plate.
5. Do not carry the oscillator by the cord. This can cause damage.
6. Keep the oscillator dry. Do not expose it to rain, snow, or frost.
7. Do not use near flammable materials, or in explosive environments.
8. Connect the power cord only after you set the switch to the middle position.
9. Install only MIG/MAG torches with the diameter of 16–22 mm (5/8–7/8″).
10. Do not stop the oscillator by hand. To stop, set the switch to the middle position.
11. Repair only in a service center appointed by the seller.
6www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
7
3. STARTUP AND OPERATION
3.1. Assembling
Use the 5 mm hex wrench to install the clamping block in the chosen position. Point
the arm down, and then install the arm and the torch holder.
INCORRECT
CORRECT
7
www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
8
3.2. Connecting
3.2.1. To the welding circuit
Put the oscillator onto a 22 mm (7/8″) diameter rod (1) and set the switch to the
middle position (2). Then, connect the power cord to the welding circuit (3). Next,
connect the power cord to the oscillator (4).
Green
Brown
White
Yellow
Welding circuit
External START-STOP
14–24 V DC
GND
Shield
1
2
3
4
8www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
9
3.2.1. To the power supply
Put the oscillator onto a 22 mm (7/8″) diameter rod (1) or a freestanding support (2,
option). Next, set the switch to the middle position (3). Then, connect the oscillator to
the power supply (4, option).
1
2
3
4
4
9
www.itmtools.com.au
OSC-8 PENDULUM WEAVE WELDER
OPERATOR’S MANUAL
OSC 8
OSC 8 Operator’s Manual
10
3.2.2. To the Rail Runner 2 welding carriage
To use the oscillator without seam tracking, assembly the oscillator with a 203 mm
(8″) rod and a clamping block (1, option). Then, use the 80 mm (3″) rod to put the
oscillator onto the carriage (2). Next, set the switch to the middle position (3) and
connect the oscillator to the carriage (4).
1
2
3
4
Part number:
KLM-0236-00-16-00-0
(203 mm rod)
KST-0525-11-00-00-0
(Clamping block)
10 www.itmtools.com.au
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Itm Système de soudage
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
ESAB
ESAB Buddy Arc 145 Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
