Itec ITECNET SPIDERLINE 16 Manuel utilisateur

SPIDERLINE 16
MANUAL
VERSION 1.0, MAY 2013
Designed and Manufactured by
ITEC Tontechnik und
Industrieelektronik GesmbH
8200 Laßnitzthal 300
Austria / Europe

ITEC SPIDERLINE 16
2www.itec-audio.com
SPIDERLINE 16 - INTRODUCTION
Dear Customer,
The main focus of our research work is and always has been the development of practical devices that are
flexible, versatile, reliable, future-proof but still easy to handle. In close cooperation with electrical consultants,
system architects and operators of public address systems the ITECNET SpiderLine16 has emerged and
grown. In addition, all our know-how from many years of experience in the field of audio and digital technolo-
gy has been integrated into this product.
Unlike any other known device, it offers the possibility of building the largest and most complex audio systems,
with relatively simple and well arranged operation and configuration.
This manual describes the hardware of the SpiderLine16, shows the construction and the wiring of the
various audio and logic I/Os and thus serves the audio system designer / integrator in the conceptual design
phase respectively during the set-up process of audio networks. Numerous examples illustrate the optimum
usage and the professional installation of controls and other devices.
For knowing the entire system, all its possibilities and for executing the necessary configuration tasks the
software manual is required in addition. Please observe during the installation / operation of the ITEC
SpiderLine16 all listed safety instructions in this manual; furthermore data and examples provided ensuring
the optimum usage of the device.
Lots of joy and success - The ITEC Acoustics Team

ITEC SPIDERLINE 16 www.itec-audio.com 3
Safety instructions
When installing the device, the local connecting conditions, the required protective measures and all relevant
standards have to be observed.
The installation and configuration of the ITEC SpiderLine16 must be performed by trained personnel only. For
the configuration the original software ITEC NetDesign has to be used exclusively.
The power connection is carried out via the original power supply unit or directly to any existing 24 V DC
power supply (emergency current).
Please note that the ground connector of the device (audio ground and ground of all digital audio interfaces)
is electrically not connected to the negative pole of the DC supply.
Please observe during the installation, that no multiple connections between the ground connector of the
device and the 24 V negative pole are put in place (see also chapter „mass concept“).
When installed in switch cabinets, pre-cautions need to be taken to ensure sufficient air exchange to avoid
overheating of the device.
Due to the great depth of the housing, support rails are absolutely necessary for installation
in 19“ cabinets.
When connecting to other devices (e.g.: sound sources, computers), the exact pin configuration and the spe-
cifications of inputs and outputs need to be observed.
Only a connection to networks, which are compliant to IEEE 802.3 (Ethernet), is possible.
Never try to open the device by force or by unscrewing. The product does not contain parts that can be re-
paired by amateurs. Please contact the manufacturer or a local distributor.
Do not apply temperatures above 50 °C, humidity larger than 95% or rain to the device.
Caution: Before carrying out any modifications on the device (only by qualified personnel) the power supply
has to be disconnected.
The device is designed for installations in 19“ cabinets / rack / frame / housing. Improper installations in fur-
niture, cabinets or distribution systems, as well as free installation have to be avoided.
SPIDERLINE 16
The picture shows the installation in a 19“ cabinet with
support rails, Rittal system.

ITEC SPIDERLINE 16
4www.itec-audio.com
SPIDERLINE 16

ITEC SPIDERLINE 16 www.itec-audio.com 5
The audio network ITECNET
ITECNET is a decentralized, Ethernet-based audio network for the simultaneous transmission of up to 64
audio channels with the highest audio quality. At the same time, a huge number of system data, measure-
ment data and IOs are controlled and transmitted. With four audio inputs, four audio outputs, serial ports and
I/Os the SpiderLine16 is one of the most important system components.
SPIDERLINE 16

ITEC SPIDERLINE 16
6www.itec-audio.com
Made in Austria
DC 24V
POWER IN
D- D+ RX TX
RS 485 RS 232
CHASSIS
GROUND
SIGNAL
GROUND
Connectors on the rear panel
Operating and display elements on the front-panel
12 34
SIGNAL INPUT
12 34
SIGNAL OUTPUT
INFO
1
1 Indicator LED: green: normal operation, yellow = failure
2 Signal level indication for the 4 line/mic inputs
3 Signal level indication for the 4 line/mic outputs
4 Info button to switch display mode of the status indicators (see Figure 5)
1 24VDC power supply, power consumption depends on the load of the internal amplifier.
Up to 5A. max. Cable section 4 mm2
2 RS 485 (see chapter serial interfaces)
3 RS 232 (see chapter serial interfaces)
4 10 VDC power supply for external control devices (e.g remote ranel)
5 Logic Outputs (see chapter logic outputs)
6 Logic Inputs (see chapter logic inputs)
7 Fault relay (See chapter fault relay)
8 ground connections (See chapter mass concept)
max. cable section 4 mm2
SPIDERLINE 16
2 3 4
821 3 4 5 6 7

ITEC SPIDERLINE 16 www.itec-audio.com 7
SPEAKER LINES
13579111315
2 4 6 8 10 12 14 16
+-+
- +- +-+-+-+-+-
+-+-+-+-+-+-+-+-+-+-
AMP 3 AMP 4
++
--
+-+-
100V AMP IN
BACK-UP IN
AMP 1 AMP 2
++
--
LINE/MIC IN
T
+-
IN 1 IN 3
OUT 2 OUT 4
T
+-
T
+-
T
+-
T
+-
T
+-
T
+-
T
+-
LINE OUT
OUT 1 OUT 3
IN 2 IN 4
SPIDERLINE 16
SPIDERLINE 16
1 2 3 4 5 6 7 8 9 10 111213141516
SPEAKER LINE MONITORING
12
5speaker line indication:
Standard (mode 0): yellow= line-detection error on this line
red= voice alarm running on this line
Pressing the info button:
Mode 1: indicates line state (LED No.16 blinking yellow)
green= Line is active,
red= Line is active and PriorityOnly
Mode2: indicates station ID (LED15 blinking yellow)
Binary code indication, 12 Bit (1=LSB, 12=MSB)
Mode3: indicates back-up status (LED14 blinking yellow)
green= normal mode,
red= back-up mode (back-up amplifier)
5
131110
9
9 Mic/Line In (see chapter audio inputs)
10 Line Out (see chapter audio outputs)
11 Speaker lines: switched 100 Volt outputs connecting to the individual lines
12 100V line inputs of the amplifiers
13 100V line inputs of the back-up power amplifiers
Maximum cable section for all terminals 1.5 mm2- unless otherwise stated.

ITEC SPIDERLINE 16
8www.itec-audio.com
SPIDERLINE 16
Block diagram DSP 1 (Main)
DSP1
OUTPUT
UNIT 1 MIX
Volume
Priority
Volume
+
-
+
-
+
-
RS 485
A
B
Ethernet
PGA
+12V
LINE/MIC IN
Gain
+
-
Ethernet-Unit
Feed CH 1-256 Get CH 1-256
A/D-Converter
Input-Matrix
EQ
Delay
OUTPUT UNIT 2
EQ
Delay
OUTPUT UNIT 3
EQ
Delay
OUTPUT UNIT 4
D/A-Converter
EQ
Delay
24V DC IN
+
-
DC
DC
5V DSP
± 12V Analog
FAULT
+
-
+
-
+
-OUT 1
+
-
+
-
+
-
SD
OPERATE/FAULT
Pilot Amp,
Relais Matrix
MIC/LINE
PGA
+12V
Gain
A/D-Converter
+
-
+
-
MIC/LINE
PGA
+12V
Gain
A/D-Converter
+
-
+
-
MIC/LINE
PGA
+12V
Gain
A/D-Converter
+
-
+
-
MIC/LINE
RS 232
LINE OUT
OUT 2
OUT 3
OUT 4
IN 1
IN 2
IN 3
IN 4
Line Detection DSP
Main

ITEC SPIDERLINE 16 www.itec-audio.com 9
DSP2
SPIDERLINE 16
8 Logic Inputs
8 Logic Outputs
Front Panel LED-Board
Signal Processing
for Line Detection
Short Circuit,
End of Line
Earth fault
Detection
Control
Main DSP
A/D
V1
V8
M
U
L
T
I
P
L
E
X
Control
A/D
V9
V16
M
U
L
T
I
P
L
E
X
B1
B4
Control
A/D
I1
I8
M
U
L
T
I
P
L
E
X
Control
A/D
I9
I16
M
U
L
T
I
P
L
E
X
Relais Matrix
Signal
Generator D/A
Pilot Amp
Earth fault
Measurement
1 –16
Block diagram DSP 2
Line Detection, IOs
IO-Handling

ITEC SPIDERLINE 16
10 www.itec-audio.com
Signal-Routing
SPIDERLINE 16
OUT1 OUT2 OUT3 OUT4
116
PILOT-
AMP
Earth fault
1
2
3
External
Amplifiers
+-+-+-+-
+-+-
V V V V
4
24V
LS-BUS
BACK-UP 1
Earth fault
-
AMP 1 BACK-UP 2
AMP 2 BACK-UP 3
AMP 3 BACK-UP 4
AMP 4
V V
V1 V16
Short Circuit/EOL Short Circuit/EOL
I I
I1 I16
SPIDERLINE 16
+-
LINE OUT
SEAKER LINES
+-+-+-
B.Up1 B.Up2 B.Up3 B.Up4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Itec Système de sécurité
Manuels Système de sécurité populaires d'autres marques

EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur

Siren
Siren LED GSM Manuel utilisateur

Detection Systems
Detection Systems 7090i Instructions de montage

Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens
Siemens FDM273 Manuel utilisateur












