ITC TS-0690 Manuel utilisateur

Intelligently digital conference

system

User Manual

TS-0690

Before using the system, please read this manual first

NOTE:

This manual only as an instructions for user, not for service purposes. From the

date of issue, if the function or technical parameters change later, another supply

mentary instruction will be added, the details can be inquired to the manufacturers.

This manual is a product manufacturer Copyright, unauthorized and any entity

or individual shall not take part or all the contents as commercial purposes.

This manual used for intelligent digital conference system.

SAFETY OPERATIONAL GUIDANCE

In order to make sure the correct operation and safety using, please comply with

the following conditions when installation, operating and maintenance.

1) Make sure the connection of the ground wire is well enough when installation.

Do not use two-core plug. And make sure the input voltage of power supply is

as same as the one marked on the main controller.

2) Do not open the cover of the unit without permission especially the

high-voltage components marked with AC 100V to 240V, or there is risk of

shock.

3) Do not put the unit in extremely cold or hot place.

4) The unit will be heating when working. Please keep environment ventilation to

avoid overheating.

5) Please power off the unit in wet weather or not in use.

6) Please disconnect the AC power wiring from the AC power supply before the

below operations:

A. Remove or re-assembly any parts of the unit.

B. Disconnect or re-connect any plug of the unit or other connection

1Non professionals without permission, please do not attempt to open the

enclosure,do not repair, in order to avoid the accident or exacerbation of

equipment damage degree.

8) Don't take any corrosive chemical powders or liquids spilled in the equipment or

in the vicinity of.

1. Introduction of Digital Conference System

About ITC Digital Conference System

◆Digital conference system is another high-tech professional product after

multimedia central control products and audio-video matrix products. It

includes discussion units, simultaneous interpretation system, IR voice

distribution, remote telephone conference, voting and camera tracking etc.

◆Based on our complete system solution idea, it could be closely compatible

with both DCS (Digital conference System) and MCS (Multimedia Central

System) to become a complete intelligent conference system solution.

◆This user manual is applicable to Intelligent Digital Conference Controller,

Discussion Units, Camera Tracking System and Telephone Conference System.

2. Features

◆Supporting 6 video signals inputs: RCA, BNC, VGA, 3 lines of video signal

inputs.

◆Built-in Scaler, transferring VIDEO signal to VGA output, capable of being set

as 800x600，1024x768，1280x1024 DPI in the software.

◆Supporting TS and TH series conference controller at the same time and

compatible with three kinds of camera tracking controllers: TH-0580,

TH-9000M and TS-0690.

◆The tracking controller has a function of screen freeze, and the period of

screen freeze could be set by the software.

◆The ID number and preset position of the camera could be set by PC. Each

camera could be preset about 127+1 and with 6 cameras at max.

◆The control camera is supporting different Baud rates such as 9600，2400，

4800，19200, and different protocols such as Samsung. VISCA. Pelcd-D.

3. TS-0690 Auto Video Tracking Controller

Functions

1) Power—Power indicator.

2) Power switch.

1) Power input, supporting AC 100-240V input.

2) To the ground.

3) VIDEO INPUTS—connecting 6 camera video signal input.

4) VIDEO OUTPUTS—output RCA, BNC, VGA3 camera video signal.

5) CODE—protocol and Baud rate setting switch (not supporting the protocol

from other supplier at present).

6) CAMERA NET— using in high-speed camera RS485.

7) DATA—connecting with the conference controller named TH-0802M.

8) CONFERENCE SYSTEM—connecting with the conference controller

(TS-0604M).

9) CONTROL SYSTEM—connecting with the central controller (PC).

4. Technical Specifications

Model

Technical specifications

Auto Video Tracking Controller

Video

Gain 0 dB

Video Bandwidth

150MHz (-3dB),full-loading

0 -10MHz:≤+/- 0.1dB

0 -30MHz:≤+/- 0.5dB

multi-channel to single channel

cross talk -50dB @ 5 MHz, -45dB @ 10 MHz

Differential phase I/OS <1.28 degree，3.58MHz

Differential phase error 0.1%, 3.58-4.43MHz

Differential phase gain error 0.1degree, 3.58-4.43MHz

The max transmission delay 5nS(±1nS)

the switching speed 200 ns(longest time)

Signal type composite video signal

video input

interface 6 BNC female interface

minimum/maximum electric

level analog signal: 0.5V ～2.0V p-p

impedance 75 Ω

back wave loss -30dB@5MHz

genlock 0.3V-0.4Vp-p

The largest DC offset error 15mV

Video output

interface

1 BNC female interface and 1 RCA female

interface

minimum/maximum electric

level Analog signal: 0.5V ～2.0V p-p

Impedance 75 Ω

back wave loss -30dB@5MHz

DC offset ±5mV ±5mV at max

conversion type vertical interval

interface 15-pin HD female interface

minimum/maximum electric

level 2.0V p-p

Impedance 75 Ω

back wave loss <-40dB@5MHz

DC offset ±5mV ±5mV at max

sync signal

input/output type NTSC 3.58，NTSC4.43，PAL，SECAM;

Controlling types

Model

Technical specifications

Auto Video Tracking Controller

serial control interface 9-pin female type D RS-232 interface

Baud rate and protocol

Baud rate: 9600, data bit: 8 bits, stop bit: 1,

without parity check bit

specifications

power supply AC100-240V 50～60Hz(power switching)

temperature temperature of storage and operating:-20°～

+70°C

Dimension 485(L)x 245(W)x 45mm(H)

Weight About 1.5kg

5. Instruction of using PC software

5.1 Six video channels，Set up the conference platform

1) Open the PC software, set the serial, switching the video through PC software,

the display screen could be switched to different channel displays.

Notice: The address of video channel should be as same as the camera's.

5.2 Screen freeze period function

1) The screen freeze period could be set through PC software from 1-6 seconds.

The screen freeze period is beside the setting period when the camera is

rotating. It also has the function of protecting power losing.

5.3 Image resolution

1) Any of the three image resolutions could be selected by PC software and it

has the function of protecting power losing.

5.4 Getting the information of code switching

1) Turning the code switching on the rear panel of the unit, re-up electricity of

the unit, click "achieve" on the PC software to get the code switching protocol of

the camera tracking controller, Baud rate and the type of camera. Checking

whether the protocol, Baud rate and camera type are as same as the real setting

of the camera connection.

If only turning the first code, choosing VISCA protocol.

If only turning the second code, choosing SAMSUNG protocol.

If neither the first or second code is turned, choosing Pelcd D protocol.

If only turning the third code, choosing the Baud rate of the control camera at

2400.

If only turning the fourth code, choosing the Baud rate of the control camera at

4800.

If both the third and fourth codes are turned, choosing the Baud rate of the

control camera at 19200.

If neither the third or the fourth code is turned, choosing the Baud rate of the

control camera at 9600.

If the fifth code is turned, it is desk top camera; if not, it is wall mount camera.

5.5 Reset to Factory Defaults

Click "Reset to Factory Defaults", the screen freeze period of this is 1S, the DPI

is 1024*768, the camera channel number is the first one(it is valid when re-up

electricity).

5.6 Camera address setting

Camera Address ，Input the corresponding camera

address to control the cameras by the following keys.

5.7 The invoking, delete and setting of camera presetting

Choosing the camera protocol, input camera address and presetting position to

control the unit.

5.8 Setting the presetting position of the unit

1) Choosing the right protocol, camera address, presetting position, unit

address, adjusting the camera position via the up and down keys to the right

unit, then click "Setting" to finish the presetting bit of the unit. After setting all

the presetting bits accordingly, the camera will automatically point to speech

unit when opening the units.

5.8.1 Supporting three kinds of camera protocol

It could control the rotation direction of the camera and the presetting bits by

selecting the three kinds of different protocols in the PC software.

Table des matières

Autres manuels ITC Système de conférence

ITC

ITC TS-0203 Manuel utilisateur

ITC

ITC TS-W100 Manuel utilisateur

ITC

ITC TS-0303 Manuel utilisateur

ITC

ITC TH-0500M Manuel utilisateur

ITC

ITC TS-0604M Manuel utilisateur

ITC

ITC TS-0622 Manuel utilisateur

ITC

ITC TS-0605M Manuel utilisateur

ITC

ITC TS-0200ME Manuel utilisateur

ITC

ITC TS-W102 Manuel utilisateur

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur