IST RETRO-M Manuel utilisateur

Installation Instructions

RETRO-M

Retrofit Intercom & Music Distribution System

Thank you for purchasing an Intrasonic Technology product. Our products are built

to provide you with years of high quality sound.

If you need assistance with the installation or operation of this product, please

contact our Customer Service Support team at 1-877-435-0670. You may also

get information on this and other Intrasonic Technology products on our website

at www.intrasonictechnolgy.com

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Doc 0001 Rev A

Table of Contents

TOPIC

CoverPage 1

TableofContents 2

SafetyInstructions 3

Do’sandDon’ts 3

Wiring 4

Maximum Number of Stations 4

8OhmSpeakers 4

ToolsNeeded 4

GettingStarted 4

RemovingtheOldMaster 5-6

WiringintheMasterStation 7-9

Installing the Master 9-10

Removing the Old Room and Patio Stations 11

Installing the New Room and Patio Stations 12-14

RemovingtheOldDoorStation 15

Installing the New Door Station 15-16

DoorStationAdapterPlate 16

TroubleShootingGuide 17

2YearLimitedWarranty 18

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 2 of 18

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 3 of 18

Safety Instructions

To reduce the risk of electrical shock, the system must be installed by a qualified installer

or dealer.

Please read the instruction manual in it’s entirety before installing.

Please do not attempt to remove or repair your existing system or the Intrasonic

Technology Retro system. Call a qualified installer or dealer.

The apparatus shall not be exposed to dripping or splashing from liquids. No objects filled

with liquids , such as vases shall be placed on the apparatus.

Before performing any work on the existing system or the Intrasonic Technology Retro

system, make sure the power is turned off.

Do not expose outdoor units like the Patio or Door unit to direct water exposure. Direct

water exposure could cause premature failure and performance issues.

Use only Intrasonic Technology certified replace parts.

NOTE: THE RETRO-M MASTER MUST BE INSTALLED IN AN EXISTING APPROVED

INTERCOM HOUSING OR THE I1000H HOUSING TO MEET LOCAL ELECTRICAL

CODES AND SAFETY REQUIREMENTS.

ATTENTION - POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE

COUVERCLE (OU L'ARRIÈRE). NON UTILISATEUR À L'INTÉRIEUR. VOIR À UN PERSONNEL

QUALIFIÉ.

CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

Don’ts

Expose any parts of the Intrasonic Technology Retro system to moisture.

Install any room, patio, or door station closer than 10 feet from each other or back to back

on the same wall. This could cause system feedback.

Perform any work on the system without turning the system power off first.

Do’s

Use a qualified installer or dealer.

Use with Intrasonic Technology approved products.

Use a dedicated 110VAC line to the master. Not using a dedicated line could cause

popping, humming or buzzing noises in the system.

Use a dedicated line with its own disconnect device.

Locate away from any heat sources.

Label all wires.

Only one auxiliary input can be installed per system.

Wiring must follow NEC 640 and 725 for audio wiring.

All holes must be filled with wires and any remaining area must be filled and sealed.

Warnings

An apparatus with Class 1 construction shall be connected to a MAINS socket outlet

with a protective earthing connection.

Un appareil avec la construction de la classe 1 sera relié à une sortie de douille de

FORCES à un raccordement

To prevent injury, this apparatus must be securely attached to the floor/wall in

accordance with the installation instructions.

Pour empêcher des dommages, cet appareil doit être solidement fixé au

plancher/au mur selon les instructions

Intrasonic Technology, Inc. 610 Presidential Dr. Suite 104 Richardson, Texas 75081 877-435-0670

Page 3 of 18

Wiring

The Intrasonic Technology Retro system is designed to work on the existing wiring. If the existing

wiring contains 3, 4, 6 or more wires, you will need to select 3 of the wires for each room, patio

and door station. Runs need to be 350 feet each or less. If the existing system is still operating, it

is a good idea to test the system and all stations to make sure the existing wires are not

damaged.

Maximum Number of Stations

The system will handle the following number of stations;

11 room stations

2 patio stations (can be used for room stations)

2 door stations

1 auxiliary input unit

8 Ohm Speakers

The Intrasonic Technology Retro system is an 8 ohm based system. External speakers need to

high efficiency speakers. Speakers rated at less than 8 ohms could degrade performance or even

damage the system.

Tools Needed

9Tape measure

9Wire stripper and cutter

9Hammer

9Drill

9Screw drivers

9Tin Snips

9Volt/ohm meter

9Pry bar

Getting Started

First determine the make and model of the system you are replacing. This includes room, patio

and door stations. Also if there are any ceiling speakers, what size they are and if they are 8 ohms

impedance. The Intrasonic Technology Retrofit system requires the use of 8 ohm speakers. This

will allow you to acquire the correct replacement components and adapter plates.

Make sure the power is off to the existing system.

Taking out the existing system can be a messy process. Bring some “drop cloths” to put under the

units to be removed.

Perform a test on the existing system operation to make sure the wiring is complete and

undamaged.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 4 of 18

Removing the Old Master

If the existing system is still operational, run a test by playing the radio and testing the

intercom functions to each room, patio and door station. If one or more of the stations do

not function, this could be a sign that there is faulty wiring.

If one of the stations does not function properly, try swapping the defect station with a

working station. If the defective station works in the new location, and the working station

now does not work in it’s new location, this is a sign that there is trouble with the wiring. If

the defective station does not work in the new location, this probably means the station is

defective.

Make sure the power to the existing system is turned off.

Remove the master unit from it’s housing.

If you encountered wiring issues in the operational test above, this would be a good time

to perform and continuity and short test on the existing wiring.

Check to see if the existing wires are marked. There should be wires for each room, patio

and door station, antenna (both AM & FM) and power. If these are not already marked,

place a tag on each wire show what station it goes to or what it is used for. If you are not

sure of the use, the printed circuit board where the wire is connected is normally marked

with connection details.

Once all the wires are marked, you can disconnect all the wires and remove the master

unit from its housing.

With the master removed, the housing should look something like this with all the wires

disconnected and marked.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 5 of 18

The Intrasonic Technology Retrofit system is designed to work with most existing

housings. To determine if you can use the existing wall housing measure the inside height

and width of the existing housing. If it measures between 14 1/8 inches to 14 3/8 inches

in width and at least 5 ¾ inches high, you should be able to use the existing housing.

If you find that you can not use the existing housing, you will need to remove the old

housing and install an Intrasonic Technology I1000H Rough-In kit.

Some old systems have the power coming in to a box that hangs from the bottom of the

wall housing that contains one or two transformers. The Intrasonic Technology Retrofit

system does not use transformers. You will need to carefully remove these transformers,

bring the Romex up into the housing for connection to the Intrasonic Technology master.

Note: Do not remove the old transformer housing and if there was a cover you will need to

save it. The cover should be replaced once the Romex is wired to the Intrasonic

Technology wires.

If you are using the original housing, you will need to install the Intrasonic Technology

mounting straps. These come with Retrofit RETRO-M master. Be sure to install them with

the flat side facing the chassis. As closely as possible mount them with the mounting screw

hole centered between the top and bottom. If there are holes available you can use them

to screw the mounting straps to the chassis. But be careful not to mount them too far

towards the back. The mounting strap needs to be no more then 1/2” from the front end

of the chassis. If there are no holes, drill holes to mount the mounting strap.

Mounting strap centered

between top and bottom

of housing. Set back from

edge

½ in

h m

The view above shows the existing master housing with the right side strap installed. When

mounting the left side strap, make sure the left and right straps are level. This will insure that the

master is level when installed.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 6 of 18

Wiring in the Master Station

Determine how many room, patio and door stations you will be installing. Remove the

appropriate number of green connectors from the rear of the master printed circuit board

Strip the existing wires ¼ inch for all the stations.

For each station there are connections marked “+15V”, “GND” & “LINK”. Select a wiring

pattern or color code system to use throughout the entire system. In other words, let’s say

you have selected red, black and white wires. Now setup a color code that you wire all red

wires to the +15V, all black wires to the GND and all the white wires to the LINK. The one

important thing to remember the same wire color scheme must be used on the end of the

wires in the master housing and on the other end at the individual room, patio and door

stations.

Leave the station wires with the connectors attached hanging in the master housing, while

you proceed to connect the rest of the wires.

This view shows the removable

connectors on the back of the

master printed circuit board.

This view shows one of the green

connectors attached to the

existing wires.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 7 of 18

Wiring in the Master Station

Prior to starting the wiring, align the plastic adapter frame to the existing rough-in box.

TIP: Hold in place by placing masking tape on the corners.

To wire the power you will need a licensed Electrician. The existing Romex will need to be

wired to the power leads on the Retrofit master, the connections placed in the old power

or transformer box and the cover replaced. DO NOT TURN ON POWER.

Proceed to wire the AM and FM antennas to the rear of the master.

Now you can plug in the removable connectors you wired to the existing wires for the

room, patio and door stations. The receptacles on the master printed circuit board are

marked for “room” “door” and “Patio”. Plug in the existing wires into the appropriate

receptacle.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 8 of 18

AUX Input

If you are installing the optional auxiliary input wall plate, you need to plug the wires

from the AUX wall plate into the two (red & white) phono jacks on the back of the

master printed circuit board.

Door Release Connection

If you are connecting to an electronic door release mechanism, connectors CN5 and CN6

provide both “Normally Open” and Normally Closed” contacts for this function. The most

common use is the normally open contacts that would close and allow power from the

bell transformer to activate the release mechanism. Make the appropriate connections at

CN5 for door 1 and CN6 for door 2.

Auxiliary input

acks

Connect door 1 to CN5

Connect door 2 to CN6

Installing the Master in the Wall Housing

Before installing the master, check that all wires are connected, there are no wires touching

or close to each other that could cause shorts, there are no strands loose that could cause

shorts and any unused existing wires are safely covered and moved out of the way.

Place the Intrasonic Technology master over the rough-in box and align the two mounting

holes over the holds in the rough-in housing. Insert one of the 2 inch mounting screws

provided and proceed to tighten for 2 to 5 turns. Once started insert the second mounting

screw and proceed to tighten. Tighten both mounting screws firmly but do not over tighten.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 9 of 18

Finish the master assembly by attaching the outer face plate and tightening the 3 screws

on the bottom of the face plate.

Important Note:

On the back of the master, the green station connectors are numbered from 1 to 13. Connectors 1

through 9 are for room stations only. Connectors 10, 11, 12 and 13 can be used for either a room

station or a patio station. But for proper operation when using these 4 ports, you must select

either room or patio on switch SW1-4 located on the back of the main printed circuit board.

Intrasonic Technology, Inc. l 610 presidential Dr. Suite 104 l Richardson, Texas 75081 877-435-0670

Page 10 of 18

Autres manuels pour RETRO-M

Table des matières

Autres manuels IST Système d'interphone

IST

IST I1000M Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques

Bticino

Bticino LINEA 3000 Manuel utilisateur

MSI

MSI MSI-140 Manuel utilisateur

golmar

golmar Stadio Plus Manuel utilisateur

CyberData

CyberData 011211 series Manuel

Vidos

Vidos duo M1021 Manuel utilisateur

Vimar

Vimar ELVOX 7539/E Manuel utilisateur

SSS Siedle

SSS Siedle BTSV 850-03 Manuel utilisateur

Dahua

Dahua VTO Series Manuel utilisateur

Elvox

Elvox 5651 Manuel utilisateur

Videx

Videx VIDEOKIT Series Manuel utilisateur

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuel utilisateur

Viking

Viking E-35-EWP Manuel utilisateur

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuel utilisateur

SSS Siedle

SSS Siedle BFCV 850 Series Manuel utilisateur

GRD

GRD MAX V2 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Aiphone

Aiphone IE-8MD Manuel utilisateur

Perel

Perel EDB4 Manuel utilisateur