Isotech ICM A7 Manuel utilisateur

ISO-TECH ICM A7

ELECTRICAL TESTER

INSTRUCTION MANUAL

INTRODUCTION

1-1 Unpacking and Inspection

Upon removing the A7 open jaw clamp meter from its packing, you should have the following items :

1. A7 open Jaw Clamp meter.

2. Instruction manual.

1-2 SAFETY

Review the following safety precautions to avoid injury and prevent damage to this product or any products

Connected to it. To avoid potential hazards, use the product only as specified.

#CAUTION. These statements identify conditions or practices that could result in damage to the equipment or

other property.

#WARNING. These statements identify conditions or practices that could result in personal injury or loss of life.

Symbols on the product

#Refer to manual 1Double Insulated □Battery

Specific precautions

1. To avoid personal injury, do not apply any voltage or current to the product without the covers in place.

2. To avoid injury or loss of life, do not touch the metal probe tips while they are connected to a voltage source,

probe tip sleeves are supplied.

3. To avoid electric shock, do not operate this product in high temperature or high humidity environment.

4. Do not use the tester if it or its test leads appear damaged, or if you suspect that the tester is not operating

properly.

5. Never apply more than the rated voltage, as marked on the tester, between a terminal and earth ground.

1-3 FRONT PANEL OVERVIEW

Refer to figure 1 and the following numbered steps to familiarize yourself with the meter’s front panel controls and

connectors.

1. Digital Display — The liquid crystal display (LCD) is a 3 1/2 digit display (maximum reading of 1999), with

autopolarity and decimal point indicators.

2. Measurement Function Dial — Rotate the function dial to select V%, V', Ω□and A%function.

3. Display Hold — To hold the reading on the display, press and release HOLD .

To exit the display hold mode, press and release HOLD again.

4. Sensor Zone — Place conductor anywhere within the sensor zone (shades area shown as Figure 2).

Figure 1

SPECIFICATIONS

2-1 General specifications

LCD display digits : 3 1/2 digit large scale LCD readout.

Display count : 2000 count.

Measuring Rate : 2.5 times / sec.

Overrange display : “OL” is displayed for “A” and “Ω” functions, shows the real value for “V” function.

Low voltage indicator : □is displayed. Replace the battery when the indicator appears in the display.

Automatic power off time : Approximately 13 minutes after power on. To resume operation, turn the tester off,

and then on again.

Power Requirement : Single 9V battery (NEDA 1604, JIS 006P or IEC6LF22).

2-2 Enviromental conditions

Indoor Use.

Calibration : One year calibration cycle.

Operating Temperature : 0℃~ 30℃(≦80%RH), 30℃~ 40℃(≦75%RH), 40℃~ 50℃(≦45%RH)

Storage Temperature : -20℃~ + 60℃(below 80% RH) with battery removed.

Temperature Coefficient : 0.2 x (Specified accuracy) / , < 18℃, > 28℃.

Operating Altitude : 2000m (6562ft)

Battery Type and Life : ALKALINE PP3, 9V 250 hours.

Overvoltage Category : IEC 1010 600V CAT.Ⅲ.

Pollution Degree : 2 Class Ⅱ

Shock Vibration : Sinusoidal vibration per MIL-T-28800E (5Hz to 55Hz, 3g maximum).

2-3 Electrical Specifications

Accuracy is ±(% reading + number of digits) at 23℃±5℃< 80%RH.

1. Voltage

Function Range Resolution Accuracy Overload Protection

V%600V rms 1V

(

1.5% + 3 di

its

)

40Hz

~ 500Hz 600V rms

V'600V 1V ±(1.0% + 2 digits) 600V rms

Input impedance : 1MΩ// less than 100pF.

2. Resistance & Continuity

Function Range Resolution Accuracy Overload Protection

Ω□2000Ω1Ω±(1.0% + 2 digits) 600V rms

Max. Open Circuit Voltage : 3V

Continuity check : Internal sounder activates if the resistance of the circuit under test is less than 25Ω. It will

then turn off if the resistance is increased beyond 400Ω.

3. AC Current

Function Range Resolution Accuracy Overload Protection

A%200A 0.1A

(

3.0% + 3 di

its

)

45Hz

~ 66Hz 200A

* Adjacent conductor influence : <0.05 A/A

OPERATION

This instrument has been designed and tested in accordance with IEC Publication 1010, Safety Requirements for

Table des matières

Autres manuels Isotech Équipement de test

Isotech

Isotech 875 Mode d'emploi

Isotech

Isotech ISIS Mode d'emploi

Isotech

Isotech ITS-90 Mode d'emploi

Isotech

Isotech IRT2310 Manuel utilisateur

Isotech

Isotech MEDUSA 510 Series Mode d'emploi

Isotech

Isotech PHTC-783 Instructions de montage

Isotech

Isotech IIT 1500 Manuel utilisateur

Isotech

Isotech PEGASUS PLUS 1200 Series Manuel utilisateur

Isotech

Isotech Saturn 878 Mode d'emploi

Isotech

Isotech LCR 1705 Manuel utilisateur

Isotech

Isotech Quick-Cal Series Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur