Islander MR2 Caractéristiques techniques

Maintenance Instructions

For MR2 Mooching Reel

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

Thank you for purchasing an Islander MR2 model mooching reel.

In this manual you fill find information on how to take care of your new

reel. Concise illustrations will help you identify, clean, and lubricate

each important component to help keep your reel performing like new.

Full frame construction with one piece spool and frame.

Free spool operation controlled with frame-side recessed lever.

One way large cork disc drag system.

Face side adjustable drag knob.

Islander classic outgoing clicker.

A generous palming rim.

Engraved serial number on spool or frame. (Note: you may

notice that your spool and frame serial number do not match,

which is by design.)

Features of the MR2

Maintenance Instructions

How To Disassemble Your Reel.

1. Remove the retaining screw by

turning it counter-clockwise, using

a snug-fitting flat bladed screw

driver or coin. (It is important that

whichever tool you choose to use

fits well, as one that is too small

may damage the retaining screw.)

2. Remove the dragknob by turning it

counter-clockwise until it is loose.

Underneath the dragknob there

will be a stainless steel washer. It

will either be stuck to the bottom

of the dragknob or to the top of the

dragspring.

3. Grasp the outside of the frame with one hand and the

spool with the other, and pull the frame and spool

apart. On the back of the spool you may notice that the

clutch is stuck the back of the spool. You can remove

this by grasping the teeth of the clutch and pulling.

t this point there should be 7 free assemblies: Retaining

Screw, Dragknob, Dragknob Washer, Dragspring, Clutch,

Spool, and Frame.

(A) Retaining Screw

(B) Dragknob Figure 1

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

Cleaning and Lubricating Your Reel Your reel comes from the factory lubricated.

Periodic lubrication is recommended to maintain

optimum performance.

1. Disassemble your reel as per instructions on

Page 2 of this manual.

2. If the clutch assembly [1] has not been

removed, please do so now.

3. Clean the clutch assembly. Remove old

grease and grit using a soft cloth.

4. Clean the base of the spindle, [2]. Remove

any old grease and grit from using a soft

cloth.

5. Clean the pawl/cam assembly [A] and [B].

Remove any old oil and grit using a brush or

swab.

6. Oil and grease all indicated locations.

7. After lubrication, work the Draglever [3]

back a forth a few times to work the

lubrication through the cam and pawl

assemblies.

8. With the Draglever [3] in the “open”

position (as pictured), lower the clutch

back into position, cork side up. Rotate

the Draglever [3] into its “closed”

position.

C) Grease

Cam

B) Oil

Cam

) Oil

Pawl

2) Spindle

1) Clutch

ssembl

Figure 2

E) Oil

Clutch

Cork

D) Grease

Teeth of

Clutch

F) Grease

Bearing Under

Clutch.

3) Draglever

Figure 3

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

9. Remove old oil from the around the

clicker assembly using a brush or

swab.

10. Remove old grease from the

surface of the bearings. One

bearing is located at [G], while the

other bearing is on the other side of

the spool. If the dragspring [Figure

5] has not been removed, please do

so to clean and lubricate this

bearing.

11. The dragspring does not require

any lubrication. Just wipe the

dragspring off with a soft cloth.

12. The handle assembly need not be lubricated. Simply remove the

screw holding the handle with a flat bladed screw driver and clean

thoroughly with warm, soapy water.

This level of cleaning or lubrication should be carried out once every 3-4

fishing trips. Because of the conditions that this style of reel is used

under (saltwater), it is important that the reel be rinsed off under a warm

water stream after each trip. While the reel is saltwater safe, the quick

rinse will help your reel perform better in the long run. Avoid immersing

the spool in water, because moisture will be retained by the backing. Figure 6 –

Handle

ssembl

G) Grease

Bearings (front of

spool and rear of

spool)

F) Oil Clicker

ssembl

Figure 4 Figure 5 –

Drag

Spring

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

ing

eter

2. If you find that your reel is too loud on the outgo

click, push the clicker spring [2] in the direction

indicated by [B], Figure 7. Do not push spring mo

than a few degrees, as pushing too far will remove

the outgoing click altogether.

3. If you find that your reel is too quiet on the incom

click, push the pawl spring [4] in the direction

indicated by [C], Figure 8.

4. If you find that your reel is too loud on the incom

click, push the pawl spring [4] in the direction

indicated by [D], Figure 8. Do not push this spring

more than a degree.

Tuning and Troubleshooting

It is possible to tune both incoming and

outgoing clicks, to a certain extent. For

these adjustments, you will need to

disassemble your reel.

1. If you find that your reel is too quiet

on the outgoing click, push the

clicker spring in the direction

indicated by [A], Figure 7. Push

the spring until the clicker [1] is

pointing directly at the bearing on

the rear of the spool.

B) For a qui

outgoing click

) For a louder

outgoing click

2) Clicker Spring

1) Clicker

Figure 7

D) For a quieter

incoming click.

3) Pawl

)

Pawl Spring

C) For louder

incoming click.

Figure 8

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

Clicker Assembly

Bearing

Clutch Assembly

Pawl Assembly

Cam Assembly

Spool

Handle Assembly

Dragknob

Retaining Screw

Frame

Draglever

Foot

Major Components

For parts and service

call toll free: 1-888-404-1119

www.mikesreelrepair.com

Maintenance Instructions

Recommend Lubricants

Islander recommends the use of Super Lube® brand oil and grease with Teflon® for all

lubricating applications. Super Lube® is manufactured by: Synco Chemical Corp., N.Y.

Teflon® is a registered trademark of E.I. duPont DeNemours & Co.

Oil: Super Lube® Multi-Purpose Synthetic-based Oil with PTFE®

Grease: Super Lube® Multi-Purpose Lubricant with Teflon®

Recommended Adhesives

Islander Reels recommends the use of Loctite® 262 Permenent Threadlocker and Loctite®

242 Removable Threadlocker. Loctite® 262 and Loctite® 242 are registered trademarks of

Loctite Corp., U.S.A.©

If you have any questions or comments about your reel, please phone,

fax, or e-mail Islander Reels. If Islander Reels requests that your reel be

sent in for repair, please remove the line from the reel.

Islander Reels

6771 Kirkpatrick Crescent

Saanichton B.C. V8M 1Z8

Canada

Phone (250)544-1440

Fax

Email info@islander.com

Site www.islander.co m

Product Information

(250)544-1450

Table des matières

Autres manuels Islander Matériel de pêche

Islander

Islander LX Series Caractéristiques techniques

Islander

Islander ARMR2 Manuel utilisateur

Islander

Islander Steelheader Instructions d'utilisation et d'entretien

Islander

Islander MR3 Series Caractéristiques techniques

Islander

Islander ARMR2 Manuel utilisateur

Islander

Islander Trout Series Instructions d'utilisation et d'entretien

Islander

Islander IS Manuel utilisateur

Islander

Islander MR3 Manuel utilisateur

Manuels Matériel de pêche populaires d'autres marques

Kongsberg

Kongsberg Simrad SY50 Manuel utilisateur

Cannon

Cannon Magnum 5 ST Manuel utilisateur

Jiffy

Jiffy Pro4 Lite Manuel utilisateur

Fishmaster

Fishmaster Pro Series Guide de démarrage rapide

MIVARDI

MIVARDI Carp Scout XL Manuel utilisateur

FLAJZAR

FLAJZAR FISHTRON CatFish TX3 Manuel d'exploitation et d'entretien

Milwaukee

Milwaukee 2873-20 Manuel utilisateur

VEXILAR

VEXILAR FL-8SLT Manuel utilisateur

Fishmaster

Fishmaster Casting Platform Guide de démarrage rapide

Marcum Technologies

Marcum Technologies PanCam Manuel utilisateur

Harmony

Harmony SlideTrax 8023061 Manuel utilisateur

Quantum

Quantum Baitcast Reel Manuel utilisateur

K-Drill

K-Drill Ice Auger Manuel utilisateur

FISHING SPECIALTIES

FISHING SPECIALTIES Bowducer Manuel utilisateur

Fox

Fox Receiver Manuel utilisateur

Abu Garcia

Abu Garcia REVO MGX Manuel utilisateur

Daiwa

Daiwa TanacomBull 1000 Manuel utilisateur

Sealey

Sealey HP01 Manuel utilisateur