ION TOTAL PA TITAN Manuel utilisateur

User Guide

English

TOTAL PA™ TITAN

Tap or click

for technical

support.

ionaudio.com/support

ION Audio Total PA™ Titan User Guide 3

Thank you for purchasing the Total PA™ Titan. At ION, your entertainment is as important to

us as it is to you. That’s why we design our products with one thing in mind—to make your life

more fun and more convenient.

Box Contents

Total PA™ Titan

IEC320 C13 Power Cable (5 ft / 150 cm)

Quickstart Guide

Support

For the latest information about this product (documentation, technical speciﬁcations, system

requirements, compatibility information, etc.) and product registration, visit ionaudio.com.

For additional product support, visit ionaudio.com/support.

Quick Start

1. Make sure all items listed in the Introduction > Box Contents

are included in the box.

2. Read the Safety & Warranty Manual before using the product.

3. Study the Setup > Connection Diagram

4. Make sure all input devices (e.g. microphones, CD players, or digital media players) are

turned o with their volume settings set to “zero.”

5. Connect all devices as shown in the Connection Diagram.

6. Switch everything on in the following order:

a. Audio input devices (e.g. microphone, instruments, CD players)

b. Total PA™ Titan

7. When you are ﬁnished using Total PA™ Titan, switch everything o in the following order:

a. Total PA™ Titan

b. Audio input devices

INTRODUCTION

ION Audio Total PA™ Titan User Guide 4

Stand Mounting

Note: Speaker stand not included, sold separately.

1. Fully extend the speaker stand tripod legs on a ﬂat, stable surface.

2. Raise the mounting pole up to the appropriate height needed and tighten the side

adjustment knob.

3. Insert the pin into the bottom pin-hole so the mounting pole stays at your set height.

4. On the Total PA™ Titan, adjust the bottom knob counter-clockwise so the screw is not

blocking the opening.

5. Line up the Total PA™ Titan mounting hole with the speaker stand pole and place on the

pole.

6. Tighten the mounting knob clockwise on Total PA™ Titan to secure it to the pole.

SETUP

235

ION Audio Total PA™ Titan User Guide 5

Connection Diagram

Microphone

USB drive

Smartphone

Power

Tablet, etc.

PUSH TO SELECT

AUX IN CLIPPWR

XLR IN MIX OUTMIC IN

POWER

OFF

ION Audio Total PA™ Titan User Guide 6

Rear Panel

Click a control below to jump to that section.

FEATURES

PUSH TO SELECT

AUX IN CLIPPWR

XLR IN MIX OUTMIC IN

POWER

OFF

ION Audio Total PA™ Titan User Guide 7

1. Display

This screen shows information relevant to the current operation on Total PA™ Titan.

Note: The Display comes with a plastic protector on it. Remove this for optimal viewing.

2. Control Knob

Push this knob to cycle between the following controls, as indicated on the Display, and

then turn the knob to adjust the selected control:

•VOL: Adjusts the overall main volume of the loudspeaker (0–30).

•MIC: Adjusts the microphone input volume, independently of the other channels (0–

30).

•SOURCE: Adjusts the source volume (Bluetooth, AUX, or USB), independently of the

Mic channel (0–30).

•ECHO: Adjusts the amount of echo effect on the microphone (0–10).

•LOW: Increases or decreases the low frequency EQ for all channels (-12 – 0– 12).

•HIGH: Increases or decreases the high frequency EQ for all channels (-12 – 0– 12).

If the Control Knob is not moved for five seconds, the function will return to VOL.

Press and hold the Control Knob for five seconds to restore the default settings.

Note: For the best sound quality, set your input source volume to 100% and use the Source

and Main Volume control of the speaker to adjust the volume.

See the section Operation > Using the Control Knob for more information.

3. Next Button

Press this button to skip to the next Bluetooth or USB track.

4. Previous Button

Press this button to return to the start of the current Bluetooth or USB track. Press the

button again within one second to skip to the previous track.

5. Play/Pause Button

Press this button to start and stop Bluetooth or USB audio.

Press and hold this button to enable or disable the voice prompts.

ION Audio Total PA™ Titan User Guide 8

6. Stereo-Link™ /Repeat Button

Press and hold this button to start stereo-linking to another Total PA™ Titan. See Operation

> Linking Two Speakers for more information.

In USB mode, press this button to change the playback mode. See Operation > USB Mode

for more information.

7. Source Button

Press this button to cycle between Bluetooth, Aux, and USB modes. The current mode will

be shown on the Display.

8. Lights Button

Press this button to cycle between the modes, or to turn the lights off. See Operation >

Light Modes for more information.

9. USB Charge/Playback Port

You can use this port for charging the USB device, such as a tablet or smartphone. To

charge a device that is streaming music via Bluetooth, pause the music first and then wait

for it to reconnect after the USB cable (not included) is inserted.

You can also connect a USB flash drive here to play music. See Operation > USB Mode for

more information.

10. Mic Inputs

Connect a microphone or mic-level source to these inputs using 1/4” / 6.35 mm and XLR

cables.

11. Aux Inputs

Connect a CD player, MP3 player, or other audio source to these inputs using 1/8” / 3.5 mm

and XLR cables.

12. Mix Out

Connect this output to a speaker, mixer, or recorder using an XLR cable.

13. Power LED

This LED will be lit when the unit is powered on.

ION Audio Total PA™ Titan User Guide 9

14. Clip LED

This LED will ﬂash red if the signal from the input jacks or audio source is clipping

(distortion from an overly loud signal). If this happens, decrease the main volume or the

source volume for the Aux or Mic Inputs (if a loud device is plugged into either) using the

Control Knob.

15. Power Switch

Turns Total PA™ Titan on or o. When the power is on, the Power LED will be lit green.

16. Power Cable Input (IEC)

Connect the included power cable here to power the unit.

ION Audio Total PA™ Titan User Guide 10

Using the Control Knob

The Control Knob defaults to controlling the Main Volume for all channels. Press the Control

Knob to toggle through dierent functions. Rotate the Control Knob to change the selected

setting:

Press Control Rotate

1x MIC Adjust mic volume

2x SOURCE Adjust source (AUX, Bluetooth USB) volume

3x ECHO Adjust mic echo

QEwoltsujdAWOLx4

QEhgihtsujdAHGIHx5

6x VOL Adjust main volume

If there is no activity on the Control Knob for 5 seconds, the function will go back to Main

Volume.

To factory reset the speaker to default settings, hold down the Control Knob for 5 seconds.

The speaker will power cycle and the reset will be successful.

OPERATION

1 2

ION Audio Total PA™ Titan User Guide 11

Pairing a Bluetooth® Device

1. Turn on your Bluetooth device.

2. Power on Total PA™ Titan. When the unit is ﬁrst turned on, it will automatically enter

Bluetooth pairing mode. If necessary, press the Source button to select Bluetooth mode. If

voice prompts are enabled, you will hear “Bluetooth Pairing.”

3. Navigate to your Bluetooth device’s setup screen, ﬁnd “TOTAL PA TITAN” and connect. If

voice prompts are enabled, you will hear “Bluetooth Connected.”

Note: If your Bluetooth device prompts for a pairing code, enter “0000”.

To disconnect the paired Bluetooth device, turn o or disconnect from your Bluetooth

device.

Tip: If you would like to disable (or enable) the voice prompts, press and hold the Play / Pause

button for ﬁve seconds.

TOTAL PA™ TITAN

1 - PRESS 2

Autres manuels pour TOTAL PA TITAN

Table des matières

Autres manuels ION Système de haut-parleurs

ION

ION BLOCK ROCKER BLUETOOTH Manuel utilisateur

ION

ION Total PA Premier Manuel utilisateur

ION

ION Total PA Supreme Manuel utilisateur

ION

ION TOTAL PA GLOW 3 Manuel utilisateur

ION

ION WATER ROCKER Manuel utilisateur

ION

ION TOTAL PA GLOW 3 Manuel utilisateur

ION

ION ANYROOM Manuel utilisateur

ION

ION Total PA Premier Manuel utilisateur

ION

ION Total PA Supreme Manuel utilisateur

ION

ION TOTAL PA TITAN Manuel utilisateur

ION

ION PROJECT ROCKER Manuel utilisateur

ION

ION Game Day Lights Manuel utilisateur

ION

ION TAILGATER BLUETOOTH Manuel utilisateur

ION

ION Mega Party Express Manuel utilisateur

ION

ION EXPLORER EXTREME Manuel utilisateur

ION

ION TOTAL PA GLOW Manuel utilisateur

ION

ION Block Rocker iPA76C Manuel utilisateur

ION

ION EXPLORER EXTREME Manuel utilisateur

ION

ION Pro Glo Duo Manuel utilisateur

ION

ION Total PA Supreme Manuel utilisateur

ION

ION TAILGATER BLUETOOTH Manuel utilisateur

ION

ION Block Party Live Manuel utilisateur

ION

ION Total PA Live Manuel utilisateur

ION

ION Pathfinder Manuel utilisateur

Manuels Système de haut-parleurs populaires d'autres marques

JVC

JVC CA-MXK5R Manuel utilisateur

LG NB4532B Manuel utilisateur

JVC

JVC CA-FSH100 Manuel utilisateur

5Core

5Core Pro Series Manuel utilisateur

EAW

EAW MQV1394e Manuel utilisateur

Lynx

Lynx GXR-LA10A Manuel utilisateur

iLive

iLive ITB066B Manuel utilisateur

RDX

RDX QuickStation 4 Manuel utilisateur

Electro-Voice

Electro-Voice S-122 Manuel utilisateur

Sven

Sven SPS-619 GOLD Manuel utilisateur

Pioneer

Pioneer CS-7070 Manuel utilisateur

EAW

EAW UB82e Manuel utilisateur

Sondpex

Sondpex Active Speaker System and Digital Music... Manuel utilisateur

JVC

JVC NX-PN7 Manuel utilisateur

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuel utilisateur

Yamaha

Yamaha NX-A01 - Speaker Sys Manuel utilisateur

SE Audiotechnik

SE Audiotechnik I-LINE Manuel utilisateur

Gemini

Gemini WRX-843 Series Manuel utilisateur