IntesisBox Modbus Server-FC330A Manuel utilisateur

IntesisBox

Modbus Server – FC330A

Doc. Rev.

Installation Manual

URL

tel

http:/

/www.intesis.com

[email protected]

+34 938047134

1 / 5

This information is subject to change without notice.

•

IntesisBox must be installed by accredited electrician or similar technical personnel, following all the safety instructions

given here, and in accordance always with the country legislation for installation of electric equipment.

•IntesisBox can not be installed outdoors or exposed to direct solar radiation, water, high relative humidity or dust.

•IntesisBox must only be installed in a restricted access location

•In case of wall mount, fix firmly IntesisBox on a not vibrating surface following the instructions below.

•In case of DIN rail mount fix IntesisBox properly to the DIN rail following the instructions below.

•Mounting on DIN rail inside a metallic cabinet properly connected to earth is recommended.

•Disconnect always power of any wires before manipulating and connecting them to IntesisBox.

•A power supply with an NEC Class 2 or Limited Power Source (LPS) and SELV rated is to be used.

•Respect always the expected polarity of power and communication cables when connecting them to IntesisBox.

•Supply always a correct voltage to power IntesisBox, see details of voltage range admitted by the device in the technical

characteristics below.

•This device was designed for installation in an enclosure. To avoid electrostatic discharge to the unit in environments with

static levels above 4 kV precautions should be taken when the device is mounted outside an enclosure. When working in

an enclosure (ex. making adjustments, setting switches etc.) typical anti-static precautions should be observed before

touching the unit

Safety Instructions

WARNIN

Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your

health and also may damage seriously the IntesisBox and/or any other equipment connected to it.

Use the software LinkBoxMB to configure IntesisBox, follow the instructions of the user's manual for more

details.

See instructions to download and install the latest version of LinkBoxMB and

the user's manual at

http://www.intesis.com/down/mb/linkboxmb.html

Configuration and setup

•Disconnect from mains the power supply before connecting it to IntesisBox.

•Disconnect power of any bus or communication cable before connecting it to IntesisBox.

•Mount IntesisBox on the wall or DIN rail following the instruction given below, respecting the safety

instructions given above.

•Connect a NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply to IntesisBox,

respect the polarity if DC power or Line and Neutral if AC power. Apply always a voltage within the range

admitted by IntesisBox and of enough power (see technical characteristics).

•Circuit-breaker must be used before the power supply. Rating 250V-6A

•Connect the communication cables to IntesisBox, see details on the user's manual.

•Power IntesisBox and the rest of devices connected to it.

Installation instructions

IntesisBox

Modbus Server – FC330A

Doc. Rev.

Installation Manual

URL

tel

http:/

/www.intesis.com

[email protected]

+34 938047134

2 / 5

This information is subject to change without notice.

IntesisBox

www.intesis.com

61 mm

100 mm

Ø 3 mm

1. Separate the fixing clips in the bottom of the box, pushing them to the outside until hear the "click" which

indicates that now the clips are in position for wall mount, see in the figure below.

2. Use the holes of the clips to fix the box in the wall with screws. Use the template below for the wall holes.

With the clips of the box in their original position, insert first the box in the upper edge of the DIN rail and later insert

the box in the down part of the rail using a small screwdriver and following the steps in the figure below.

Clips in their original position, for DIN rail

mount Clips in position for wall mount

DIN

Rail

Top view of the box

DIN rail mount

Side view of the box

Botton view of the box

Wall mount

IntesisBox

Modbus Server – FC330A

Doc. Rev.

Installation Manual

URL

tel

http:/

/www.intesis.com

[email protected]

+34 938047134

3 / 5

This information is subject to change without notice.

Connections

________________________________________________________________________________________

Notes:

1. Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply.

If using DC power supply:

•Respect polarity applied of terminals (+) and (-). Be sure the voltage applied is within the range admitted (9 to 30 Vdc).

The power supply can be connected to earth but only through the negative terminal, never through the positive terminal.

If using AC power supply:

•Make sure the voltage applied is of the value admitted (24 Vac). Do not connect any of the terminals of the AC power

supply to earth, and make sure the same power supply is not supplying any other device.

2. Modbus connection. Only one type of modbus connection can be used simultaneously, Modbus TCP, Modbus RTU EIA485, or

Modbus RTU EIA232, the type of Modbus connection to use must be selected within the configuration software LinkBoxMB.

Modbus TCP connection: This connection with the Modbus TCP master device can be done directly using a ethernet

CAT5 crossover cable, or through the LAN of the building, in this case use a ethernet CAT5 straigh cable to connect to a

switch or hub of the LAN, check with the network administrator that the TCP traffic and the port used (502 by default) are

allowed through all the LAN path used.

Modbus RTU EIA485 connection: Connect the EIA485 bus to the connector Modbus RTU EIA485 of IntesisBox. Respect

the polarity. Remember the characteristics of the standard EIA485 bus: maximum distance of 1200 meters, maximum 32

devices connected to the bus, and in each end of the bus it must be a termination resistor of 120 ohms. IntesisBox has an

internal bus biasing circuit that incorporates the termination resistor, if you install IntesisBox in one of the ends of the bus

then do not install an additional termination resistor in that end.

Modbus RTU EIA232 connection: Connect the serial cable EIA232 coming from the Modbus RTU master to the connector

Modbus RTU EIA232 of IntesisBox, this is a DB9 male (DTE) connector in which only the lines TX, RX and GND are

used, see details of the pinout in the user's manual. Respect the maximum distance of 15 meters in this serial line

EIA232.

3. Connection with the FC330A panel: Connect the serial cable EIA232 coming from the panel to the connector FC330A EIA232 of

IntesisBox, this is a DB9 male (DTE) connector in which only the lines TX, RX and GND are used. See details of this connection in

the user's manual. Respect the maximum distance of 15 meters in this serial line EIA232.

4. Use the software LinkBoxMB to configure IntesisBox. See the user's manual for details.

Console cable 1.8 m.

DB9 Female - DB9 Male

standard. Supplied.

Modbus RTU

master EIA232

See Note 2

LinkBoxMB

Only for

configuration

See Note 4

Power

See Note 1

PC Console

- +

IntesisBox

www.intesis.com

EIA232

EIA485

- +

Modbus RTU

FC330A

Modbus RTU

master EIA485

See Note 2

EIA232

Modbus TCP

master

See Note 2

Ethernet

RJ45

Ethernet

RJ45

FC330A

Panel

See Note 3

CMN 24Vac

9 - 30Vdc

Max. 25 mA

24Vac

Max. 27mA

50-60Hz

IntesisBox

Modbus Server – FC330A

Doc. Rev.

Installation Manual

URL

tel

http:/

/www.intesis.com

[email protected]

+34 938047134

4 / 5

This information is subject to change without notice.

Enclosure Plastic, type PC (UL 94 V-0).

Dimensions: 07mm x 05mm x 58mm.

Colour Light Grey. RAL 7035.

Power

9 to 30Vdc +/- 0%, Max.: 25mA.

24Vac +/- 0% 50-60Hz, Max.: 27mA

Must use a NEC Class 2 or Limited Power Source (LPS) and SELV

rated power supply.

Plug-in terminal block for power connection (2 poles).

Terminal wiring

(for power supply

and low-voltage

signals)

Per terminal: solid wires or stranded wires (twisted or with ferrule)

core: 0.5mm

… 2.5mm

2 cores: 0.5mm

… .5mm

3 cores: not permitted

Mounting Wall.

DIN rail EN607 5 TH35.

Modbus TCP port x Ethernet 0Base-T RJ45.

Modbus RTU ports x EIA232. DB9 male connector (DTE). SELV

x EIA485. Plug-in terminal bloc (2 poles). SELV

FC330A port x EIA232. DB9 male connector (DTE). SELV

LED indicators

x Power.

2 x FC330A port activity (Tx, Rx).

2 x Modbus RTU port activity (Tx, Rx).

2 x Ethernet port link and activity (LNK, ACT).

Console port EIA232. DB9 female connector (DCE). SELV

Configuration Via console port.

Firmware Allows upgrades via console port.

Operational

temperature 0°C to +70°C

Operational

humidity 5% to 95%, non condensing

Protection IP20 (IEC60529).

RoHS compliance Compliant with RoHS directive (2002/95/CE).

Norms and

standards

CE conformity to EMC directive (2004/ 08/EC) and Low-voltage

directive (2006/95/EC)

EN 6 000-6-2

EN 6 000-6-3

EN 60950-

EN 5049 -3

Standard cable DB9male-DB9female 1,8 meters long is supplied with the device for connection to a PC COM port for

configuring and monitoring the device. The configuration software, compatible with Windows

operating systems, is also

supplied.

Technical characteristics

IntesisBox

Modbus Server – FC330A

Doc. Rev.

Installation Manual

URL

tel

http:/

/www.intesis.com

[email protected]

+34 938047134

5 / 5

This information is subject to change without notice.

Dimensions

External dimensions.

Free space recommended to install the device, with spacing enough for external connections.

5 mm

30 mm

00 mm

Power

Ethernet port

07 mm

05 mm

58 mm

Console

port

Modbus RTU

ports

FC330A

port

Table des matières

Autres manuels IntesisBox Serveur

IntesisBox

IntesisBox Modbus Server-AlgoRex Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-DALI Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-Notifier ID3000 Manuel utilisateur

IntesisBox

IntesisBox ASCII Server-KNX Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-LON Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-SUNWAYS Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-DALI Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-ATERSA Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-Mitsubishi Heavy Industries AC Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-Modbus RTU master Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-Algorinet Manuel utilisateur

IntesisBox

IntesisBox IBOX-MBS-KNX-100 Manuel utilisateur

IntesisBox

IntesisBox IBOX-ASCII-KNX Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-Cerberus ISO1745 Manuel utilisateur

IntesisBox

IntesisBox IBOX-MBS-TCP2RTU Manuel utilisateur

IntesisBox

IntesisBox IBBACMEB0100000 Manuel utilisateur

IntesisBox

IntesisBox KNX TP-1 (EIB) Manuel utilisateur

IntesisBox

IntesisBox ASCII Server-LON Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server–Modbus TCP master Manuel utilisateur

IntesisBox

IntesisBox Modbus Server-FIDELIO TCP/IP Manuel utilisateur

IntesisBox

IntesisBox Modbus TCP Server-Modbus RTU Master Manuel utilisateur

IntesisBox

IntesisBox BACnet/IP Server-FIDELIO TCP/IP Manuel utilisateur

IntesisBox

IntesisBox IBMBSKNX1000000 Manuel utilisateur

IntesisBox

IntesisBox IBOX-ASCII-KNX Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur