Interactive Furniture Advanced 4020 Manuel utilisateur

Manual - Stair light controller

”Advanced 4020”

Inhaltsverzeichnis

1 Overview 4

1.1 Description of the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Technicaldata......................................... 4

1.3 Pinassignment ........................................ 5

2 Commissioning 6

2.1 Installationofthesensors................................... 6

2.2 Connectingthesensors .................................... 7

2.3 ConnectingLED-illuminants.................................. 7

2.4 Connection of the twilight sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.5 Connecting the external switch for the continuous light function . . . . . . . . . . . . . . 7

2.6 Connectingthepowersupply ................................. 8

2.7 Correct use of the connection terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Conﬁguration of the control unit 9

3.1 Entering number of stairs (STEPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3.2 Calibrating the on and oﬀ switching speed . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.3 Calibrating of the pause between the switch-on and switch-oﬀ process . . . . . . . . . . . 10

3.4 Activation and calibration of the twilight sensor . . . . . . . . . . . . . . . . . . . . . . . 10

3.5 Function ”1st step illumination” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.6 Function”QuickStart” .................................... 10

3.7 RESET-key .......................................... 10

3.8 TEST-key ........................................... 11

3.9 Status-LEDs.......................................... 11

4 Further hardware features 11

4.1 Ambientlightning....................................... 11

4.2 Internalfuses ......................................... 11

4.3 Busconnections........................................ 11

5 Further information 12

5.1 Correctusage ......................................... 12

5.2 Operating conditions and safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . 12

5.3 Disposalinstructions...................................... 13

5.4 Warrantyandliability ..................................... 13

5.5 EG-Conformity(CEmark)................................... 14

5.6 Imprint............................................. 14

6 Notes 15

This manual is printed on ‘’Recyconomic” recycled paper from 100% recycled paper.

1 Overview

Please ensure that you have familiarised yourself with the manual before beginning commissioning the

device. This in particular applies to the chapter ¨

Operating conditions and safety instructions¨ın section

1.1 Description of the control unit

This control unit enables the sensor-controlled switching on and oﬀ of your LED stair lighting. The eﬀect

can be easily adjusted via rotary control on the device top. An external continuous light switch as well

as a twilight sensor can be connected to the control unit and thus round oﬀ the functional spectrum.

Thanks to the modular design of the control unit, the range of functions can also be expanded easily and

cost-eﬀectively.

The robust components, which are designed for the required size, as well as numerous integrated protective

circuits of the control unit, ensure a safe and long-lasting operation. The high-quality DIN mounting rail

housing according to DIN43880 permits safe and maintenance-free assembly directly in the house distribu-

tion.

A lot of value was also placed on ecological aspects. Through the use of high-quality components, the

power consumption during operation is less than half a watt - including the HF sensors. The control unit

is produced in Germany; of course, according to all the statutory standards and without the use of dubious

materials. For example, the use of tantalum capacitors is completely dispensed with.

1.2 Technical data

Technical data and operating conditions of the control unit:

Description MIN TYP MAX Unit

Power per LED outlet - - 500 mA

Number of outlets - - 20 Stk.

Load of controller (at 12V) 0.05 - 7,5 A

Supply voltage 7 12 24 V

Power consumption during operation (at 12V) - 0.25 - W

Operating temperature 0 +20 +40 ◦C

Technical data of the connection terminals:

Screw terminals LED control MIN TYP MAX Unit

Cross section single wire - - 1,5 mm 2

Cross section ﬁne wired - - 1,0 mm 2

Stripping length - 5 - mm

Force on clamping screw - - 0,15 Nm

Spring-loaded terminals LED control MIN TYP MAX Unit

Conductor cross-section - - 1,5 mm 2

Stripping length 6 - 10 mm

Spring-loaded terminals sensor connection MIN TYP MAX Unit

Conductor cross-section 0,2 - 0,75 mm 2

Stripping length 6 - 7 mm

1.3 Pin assignment

No. Description Page

1 POWER-LED – illuminated when connected 11

2 STATUS-LED – signals operating mode 11

3 Switches to adjust number of steps 9

4 Key to activate all spots 7

5 Key to calibrate sensors 10

6 ”FUNCTIONS” panel to activate control options 10 ﬀ.

7+8 Dials for ON/OFF time of spots 10

9 Duration of on/oﬀ timing 10

10 Dial for optional light-sensor 10

11 Connections for LED-spots 7

12 Connection SENSOR 1 for sensor at beginning of the stairs 7

13 Connection SENSOR 2 for sensor at the end of the stairs 7

14 Connection for light-sensor 7

15 Connection for the continuous light function switch 7

16 Connection of the power supply 8

2 Commissioning

If you are not sure about the correct connection or if questions arise which are not clariﬁed by this

manual, please contact us before commissioning! Email: supp[email protected]

2.1 Installation of the sensors

The use of the enclosed indoor sensors makes it possible to detect people who are passing by and to

activate the running light. For this purpose, a sensor is installed at the beginning, as well as at the end

of the staircase. In contrast to an ordinary light barrier, motion detection is carried out exclusively from

a stairway and thus also allows installation on single-sided open stairs. Reﬂectors or additional infrared

transmitters / receivers are not required. The range of the sensor is about one meter.

In principle, two installation options are provided:

1.: Positioning of the sensor at the height of the ﬁrst step: Installed such that the lighting is activated

precisely when entering the staircase. If desired, the ”Quick start” function (see section 3.6) can be used

to switch on the ﬁrst three LED outputs so that the steps in front of you are instantly illuminated.

2.: Positioning of the sensor approximately 50 cm in front of the stairs: When installed just before

the staircase, the light is activated a moment before entering the staircase. This has the advantage that

the ﬁrst steps are already illuminated when entering the staircase and you do not walk into darkness.

Further installation instructions:

•The installation height must be selected in such a way that the sensor is always traversed and not

stepped over. A guideline is about 20-50 cm above the ground / step.

•When mounting the sensors, ensure that they are installed horizontally with the sensor lenses to the

opposite side of the staircase. This is the only way to ensure optimal recognition.

•The sensors automatically calibrate when the control unit is put into operation and thus adjust to

the width of the staircase. This calibration is performed again at every start-up.

•The sensors should be protected against contamination and contact, since this would otherwise impair

the function of the sensors.

•It is recommended to use the supplied sensor cable. It is not permissible to loop the sensor cable

through multi-conductor cables - together with LED leads -.

•If possible, the sensor cable should be laid separately from other cables (230 V) in order to avoid

disturbances in motion detection..

2.2 Connecting the sensors

The bottom step sensor (LED- channel 1) should be wired to connection SENSOR 1, and the top step to

SENSOR 2.

The coloured markings of the supplied sensor cable must be connected to the control unit as well as to the

sensor connection adapter as follows:

green = + (Power supply - 5V)

brown = - (Earth/GND)

white = S (sensor connection)

2.3 Connecting LED-illuminants

The connection leads of the LED illuminants are screwed on to the connection terminals located on top

of the control unit. The polarity can be found in the graphic on page 5, as well as in the labelling on the

control unit. The ﬁrst LED spot at the beginning of the stair is connected to terminal 1 of the control unit

- all further spots follow in the order in which they were installed.

The number of connected LEDs must be entered in the conﬁguration of the control unit - see section 3.1.

Please also provide for a suﬃcient dimensioning of the conductor cross-section of 0.5 mm2 or greater.

2.4 Connection of the twilight sensor

The control unit supports the connection of an external light sensor to deactivate the control by day (page

5 - no. 18). A polarity is not to be considered when connecting the twilight sensor. For information on

conﬁguring the twilight sensor, see page 10 of this manual.

CAUTION!

Not a potential-free connection! No voltage may be applied to these contacts!

Only the connection of the ”interactive furniture twilight sensor” is envisaged.

2.5 Connecting the external switch for the continuous light function

The control unit supports the connection of an external switch or relay (for example, a relay actuator

of a home automation system) to activate the continuous light function (page 5). When the ”ON” and

”GND” contacts are connected, all connected LED illuminants are activated and remain active until the

connections are disconnected. The sensor-controlled automatic is out of operation in this mode. When the

continuous light function is activated, the green ”STATUS” LED is lit continuously. See section 3.9.

CAUTION!

Not a potential-free connection! No voltage may be applied to these contacts!

Only the connection of the contacts via a switch is envisaged.

2.6 Connecting the power supply

The supply voltage (maximum 24V-DC) of the control unit is connected to the contact 16 of the overview

graphic on page 5. The left plus pole supplies the control unit itself as well as the LED channels 1 to 10 -

the right plus pole the LED channels 11 to 20. This allows - for the distribution of the connection load -

the use of two separate power supplies (Attention: the Minus pole is internally pressed). The polarity can

be found in the graphic on page 5 as well as in the labelling on the control unit.

IMPORTANT:

•The supply voltage must be selected in accordance with the connected LED illuminants, since these

can otherwise be damaged. Example: A 12V power supply has to be used for 12V LED strips.

•The supply voltage must not exceed 24 V (direct current).

•Use a power supply unit with suﬃciently dimensioned output power.

•Make sure that the power supply is connected to the correct polarity.

•Connect both minus and both positive poles with the power supply unit, as otherwise the LEDs 11-20

are not supplied with voltage.

ATTENTION - DANGER TO LIFE!

NEVER connect the control unit directly to the 230V power supply!

2.7 Correct use of the connection terminals

LED control - LED outputs: Single and ﬁne-wire cables with a cross-section of max. 1.5 mm2 can be

used. We recommend the use of wire-end terminals - otherwise, isolate the cable over a length of 5 mm.

Feed the cable into the screw terminal and screw it. Subsequently check the cable for a ﬁrm hold.

LED control - spring-loaded terminals: Single- and ﬁne-wire cables with a cross-section of max. 1.5

mm2 can be used. Isolate the cable to a length of 6 to 10 mm and insert it into the spring-loaded terminal.

To close the spring clamp, simply move the eccentric lever downwards. Subsequently check the cable for a

ﬁrm hold.

Sensor connection adapter: Single and ﬁne-wire cables with a cross-section of 0.2 to 0.75 mm2 can be

used. Isolate the sensor connection cables to a length of 6-7 mm. The terminals on the sensor connection

adapter can be opened by applying low pressure to the actuation press-ins - use the supplied tool. Insert

the cables into the terminals. Subsequently check the cable for a ﬁrm hold in the terminal.

3 Conﬁguration of the control unit

This section outlines the conﬁguration options for the control unit. Please ensure that you have read the

following information before starting up the control unit.

3.1 Entering number of stairs (STEPS)

The number of illuminated steps is entered using ﬁve switches (”STEPS”) on the control unit (page 5, no.

3). All further channels of the control serve the ambient lightning function (see 4.1).

Please refer to the following table for the correct switch positions:

Number of steps DIP1 DIP2 DIP3 DIP4 DIP5

5OFF OFF ON OFF OFF

6OFF OFF ON OFF ON

7OFF OFF ON ON OFF

8OFF OFF ON ON ON

9OFF ON OFF OFF OFF

10 OFF ON OFF OFF ON

11 OFF ON OFF ON OFF

12 OFF ON OFF ON ON

13 OFF ON ON OFF OFF

14 OFF ON ON OFF ON

15 OFF ON ON ON OFF

16 OFF ON ON ON ON

17 ON OFF OFF OFF OFF

18 ON OFF OFF OFF ON

19 ON OFF OFF ON OFF

20 ON OFF OFF ON ON

With 6-channel LED expansion device

21 ON OFF ON OFF OFF

22 ON OFF ON OFF ON

23 ON OFF ON ON OFF

24 ON OFF ON ON ON

25 ON ON OFF OFF OFF

26 ON ON OFF OFF ON

3.2 Calibrating the on and oﬀ switching speed

The speed of the switching on and oﬀ process of the light-emitting diodes can be adjusted separately with

the ”ON SPEED” and ”OFF SPEED” controllers

Turning the control dial ”ON SPEED” in a counter clockwise direction slows the switching on speed

of the LED-illuminants down to a maximum of one second per spotlight. When turned clockwise, this can

be sped up this process to a minimum of 20 milliseconds per spotlight. The change in the ”OFF SPEED”

controller has an analog eﬀect on the switch-oﬀ speed of the connected LEDs

3.3 Calibrating of the pause between the switch-on and switch-oﬀ process

The ”DELAY” slider is used to set the pause between the switch-on and the switch-oﬀ process. In this

case, it is possible to select continuously between half a second (stop on the left) and about one minute

(stop on the right).

3.4 Activation and calibration of the twilight sensor

If a twilight sensor is connected to the control unit, it is activated and adjusted via the ”LIGHT” control. In

the stop on the left the twilight sensor is completely deactivated and the automatic remains switched on even

in daylight. When rotated clockwise, the light-automatic switches on only when darkness increases.

The ”STATUS” LED goes out if the brightness value is exceeded and the automatic is thus deactivated.

A blinking of the ”STATUS” LED when the twilight sensor is activated indicates that the threshold value

is below the threshold - the automatic is activate

Important: Two minutes after activation of the control unit, this value is saved and from this point onwards

only readjusts every 30 seconds. By using the RESET-switch the threshold value can be calibrated for a

further two minutes. This function prevents the operating mode from changing ”involuntarily” when the

brightness changes brieﬂy.

3.5 Function ”1st step illumination”

With the switch 1 of the ”FUNCTIONS”- switch panel the ﬁrst and last LED-spot are switched on in a

dimmed mode to illuminate the beginning of the staircase. .

The optional twilight sensor switches oﬀ the 1st step illumination during daytime.

3.6 Function ”Quick Start”

In many installation situations it is not possible to place the motion sensor in front of the staircase. It

can thereby it can happen that you enter the stairs with the ﬁrst steps still unlit, with the lighting only

subsequently catching up from the rear.

To prevent this, we have the developed the ”Quick Start”-feature: The ﬁrst stages are activated in increased

speed for instant illumination. The switch 2 of the ”FUNCTIONS”-panel activates this feature.

3.7 RESET-key

Pressing the RESET-key recalibrates the sensors. This becomes necessary if the setting on the sensors and

control changes. This also occurs after each interruption of the control voltage supply.

Table des matières

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur