Intellinet IDC-757IR Manuel

Network Mini Dome Camera

Hardware Installation Guide

Package Contents

Dome Camera IDC-757IR Outdoor Megapixel Night-Vision

Network Dome Camera

Quick Installation Guide

Brief product information and quick

installation

Software CD

IP Surveillance Software

Intelligent IP Installer

User Manuals

Language Packs

Accessories 6 pin terminal cable for DI/DO and audio

Screw pack for wall and ceiling mounting (2

screws, 2 plastic wall anchors)

Focus Adjustment

Drill Template

Hardware Description

Built-in Microphone Slide cover

Top cover

Dome bubble

Factory Reset

Reset: With the camera turned on, press the reset button briefly to reboot the camera,

or hold the reset button for 10 seconds to set all settings back to factory default values.

Mounting

hole

Routing hole

Focus Adjustment Ring

MicroSD/SDHC

Ethernet / PoE Connector

Reset Button Power LED Indicator

Network LED Indicator

External I/O connector

180°

mark

I/O Terminal Block

The Intellinet Network Camera provides an external I/O terminal block

which is used to connect input / output devices such as alarms or sensors.

The pin definitions are described below

PIN Definition Description Max. V/A

1 Ground -

2 + 5V DC 5V DC

0.5W

3 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

4 AUDIO_In(+) Unbalanced, 1.4Vp-p, 1Vrms, terminal block

5 Digital Output

Uses an NPN transistor with the emitter connected to

the GND pin. If used with an external relay, a diode

must be connected in parallel with the load for

protection against voltage transients.

100 mA

24V

7 Digital Input 1 Connected to GND to activate, or leave floating (or

unconnected) to deactivate. 30V DC

LED Indicators

LED Color Indication

Network Blue Network activity is indicated by a flashing blue LED.

Power

Red Steady red during booting up process

Blue Turns blue upon completion of start-up

Purple Flashing during firmware upgrade

Unlit Off when press reset button is pressed

Hardware Installation

1) To open the camera housing use one hand to hold top cover and another hand to

push against the bottom of the camera housing.

2) Shift top cover to left (counter-clockwise) to open the dome cover. The cover will

not easily come off unless you apply a certain amount of force.

3) Attached the drill template to the wall. Drill three holes into the wall (two for

screws and one for the connection cable if you want to route cables through

conduit hole). Then push the supplied plastic anchors into the screw holes and

secure the plate with supplied screws.

4) Align the three holes on the base of camera with the two plastic anchors on the

wall or ceiling, insert the supplied screws to the corresponding hole and screw

them.

5) Adjust the angle of camera to aim the shooting area.

Lens Adjustment

WARNING:

DO NOT rotate the lens more than 360 degrees. Doing so will damage the camera lens module.



Rotate 360° Tilt 79°

Pan

344°

Cable Connections

Power over Ethernet (PoE)

Using a standard RJ-45 network cable, connect the dome camera to a

IEEE802.3af/at compliant PoE switch or PoE injector.

RJ-45 Cable

Due to the very compact housing dimensions, using a network cable with

a molded boot is not advisable. There is not enough room to connect the

RJ45 connector to the socket without bending the cable, which will likely

short the lifespan. We recommend using a network cable without a

modeled strain relief boot.

Accessing the camera

Start the IP Installer application to set up the camera. More information

can be found in the user manual on the installation CD.

INTELLINET NETWORK SOLUTIONS™ offers a complete line

of active and passive networking products.

Ask your local computer dealer for more information or visit

www.intellinet-network.com

SOLUTIONS

All products mentioned are trademarks or registered trademarks of their respective

owners.

Autres manuels pour IDC-757IR

Table des matières

Autres manuels Intellinet Caméra de sécurité

Intellinet

Intellinet 550437 Manuel utilisateur

Intellinet

Intellinet NFD130-IR Manuel utilisateur

Intellinet

Intellinet NSC15-WG Manuel utilisateur

Intellinet

Intellinet 550260 Manuel utilisateur

Intellinet

Intellinet NSC10-WG 550918 Manuel utilisateur

Intellinet

Intellinet IBC-637IR Manuel du propriétaire

Intellinet

Intellinet 503181 Manuel utilisateur

Intellinet

Intellinet NSC15 Manuel utilisateur

Intellinet

Intellinet NSC15 Manuel utilisateur

Intellinet

Intellinet IBC-667IR Manuel

Intellinet

Intellinet NFC31-WG Manuel utilisateur

Intellinet

Intellinet 524421 Manuel utilisateur

Intellinet

Intellinet PRO SERIES Manuel utilisateur

Intellinet

Intellinet IDC-757IR Manuel

Intellinet

Intellinet NSC10 Manuel utilisateur

Intellinet

Intellinet NSC11-WN Manuel utilisateur

Intellinet

Intellinet 550857 Manuel utilisateur

Intellinet

Intellinet 550260 Manuel utilisateur

Intellinet

Intellinet 550413 Manuel utilisateur

Intellinet

Intellinet IDC-767IR Manuel utilisateur

Intellinet

Intellinet 503792 Manuel utilisateur

Intellinet

Intellinet NSC10-WG 550918 Manuel utilisateur

Intellinet

Intellinet 550857 Manuel utilisateur

Intellinet

Intellinet NFC30-IRWG Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur