Intelight PRIMUS LED Manuel utilisateur

. 8, R

-7

PRIMUS LED

OPERATING INSTRUCTIONS

Dear Customer,

Thank you for the confidence you have bestowed on our company by choosing to purchase one of our devices. Prior to its use, for the sake of your own safety,

please review carefully information about the product provided below.

PRIMUS LED EMERGENCY POWER SUPPLY KIT

Primus LED is intended for installation in lighting fittings equipped with LED light source powered directly from 230V mains (versions A9 and D9) or through an

external constant current or constant voltage LED driver (versions D1, D2, D4, D6 and D8). The emergency module features compact dimensions for mounting in

small lighting fittings. The kit features a DC powered electronic ballast and a battery pack with mounting brackets. When installed, the kit enables to adapt any

lighting fitting to operate in emergency as well as mains - emergency mode.

OPERATION PRINCIPLE

The emergency module detects a failure of 230V/50Hz power and using the power stored in the battery it begins to generate high relevant voltage, necessary for

power supply of LED lamps. The duration of emergency operation depends on LED light source power rating and the capacity of battery used. The converter

reaches its full efficiency after 24 hours from connection to or restore of normal voltage. In the event of a failure of 230V/50Hz power before those 24h, the

duration of emergency operation of the device will depend on the level of battery charge. Under normal conditions, i.e. when supplied with 230V/50Hz power, the

converter charges the attached pack of high temperature batteries in a continuous mode. Battery charging as well as presence of 230V/50Hz AC power in signalled

by the green LED of the module.

CONNETION DIAGRAM

The connection diagram presented below is of illustrative nature. If in doubt, please contact a qualified electrician or the distributor from whom you purchased the

unit, or directly with our technical department.

CAUTION! Never operate the emergency module without load!

Before starting up the device, check that the LED light source has been properly connected to the system!

. 8, R

-7

GUIDANCE FOR USER

•Factory packed converter is disconnected from the battery. In this state it must not be stored in subzero temperatures as it may cause a rapid discharge. During

storage make sure the battery is not excessively discharged. The voltage of a battery pack cell should not drop below its nominal value (e.g 3.6V for a 3-cell

pack). Recharge by connecting the battery to the converter and connecting the lighting fitting to 230V/50Hz for at least 24 hours.

•It is recommended to run battery pack charging cycle during the first start up of the emergency power supply, the cycle should be at least 24 hours long.

Furthermore, it is worthwhile to format the batteries in order to increase their life. Formatting is achieved by performing three cycles of full charge and

discharge of the batteries. Discharge the battery pack by disconnecting the mains power. The lighting fitting will then switch to emergency mode.

•To avoid unnecessary discharge of the battery pack, connect it to the emergency module only after installing the LED lamp and connecting it to the mains

power. Test of the emergency lighting operation is done by disconnecting the mains power and measuring the duration of emergency operation. If it is too short,

replace the batteries after checking the electrical system for proper operation.

•Regardless of the degree of wear of the batteries, it is recommended to replace them every four years.

•The lighting fitting should work in the emergency mode only with fully charged battery. Never disable periodically the charging voltage.

•Intelight Sp. z o.o. reserves the right to change the design of the product.

GUARANTEE

Intelight Sp. z o.o. provides free removal of faults resulting from defects in material and workmanship by repairing or replacement of the device, for a period of

two years from the date of purchase. In case of malfunction, please deliver the product to the place of purchase along with a warranty tag. The guarantee shall not

cover wearing parts as well as defects resulting from improper operation of the device, in particular mechanical damage or malfunction caused by temperature or

chemical agents. Please also note that the costs of unjustified complaint shall be charged to the customer. For complete guarantee details please visit our website

at: www.intelight.eu.

DECLARATION OF CONFORMITY