Intelbras XAS Smart Manuel utilisateur

User

manual

XAS Smart

XAS Smart Black

English

XAS Smart and XAS Smart Black

Sensor

Congratulations, you have just purchased a product with Intelbras quality and safety.

The XAS Smart / XAS Smart Black wireless aperture sensor was developed by Intelbras

with 100% digital technology. The sensor is mounted on SMD components and can be

installed in most products that work at the same frequency and modulation available

on the market. It works in FSK or OOK modulation and has a low battery sensor.

Care and safety

» Follow all instructions in the manual for assembling and installing the product.

» LGPD –Data processing by Intelbras: Intelbras does not access, transfer, capture or perform

any type of processing of personal data from this product.

» This product is intended for indoor and semi-open environments.

» Respect the GAP distance (distance between the sensor and the magnet).

» Confirm that the installation location is stable and appropriate.

» Wireless communication technology, when exposed to environments with high power radia-

tion, may suffer interference and have its performance impaired, for example: locations close

to TV towers, AM/FM radio stations, amateur radio stations, etc.

» Do not expose the XAS Smart and Xas Smart Black magnetic sensors to direct sunlight, rain

and moisture.

» For your safety, test the product and systems at least once a week. This is necessary due to

changing environmental conditions, electrical or electronic interruptions, and tampering. Take

all necessary precautions for the safety and security of your property.

Summary 
1. Technical
 specifications 5 
2. 
Characteristics 5 
3. 
Product 6 
4. Sensor 
aperture 6 
5. Enrolling
 
the
 
XAS
 
Smart
 
and
 
XAS
 
Smart
 
Black
 
sensor
 7 
6. XAS
 
Smart
 
and
 
XAS
 
Smart
 
Black
 
sensor
 
supervision
 
setting
 8 
7. 
Installation 9 
8. 
Battery 11 
9. 
Test 11 
10. 
Homologation 11 
Warranty 
term 12 

Technical

specifications

Operating voltage Battery 3 V Lithium, model CR2032

Operating current 900 nA

Trigger

indication

Green

LED

range

100 meters without hurdles

Transmission frequency 433.92 MHz

Detection

Magnetic Field SMD Sensor

Modulation OOK / FSK

Baud rate OOK / FSK

KBps

(open

source)

Anti jamming Against external interference

Installation environment Internal and Semi-open

Opening gap 37 mm ± 10%

Closing

gap 27 mm ± 10%

Operating Temperature -10 °C to 50 °C

Sensor: 37 × 46 × 11 mm

Dimensions (W × H × D)

Magnet: 11 × 31 × 9 mm

Gross

weight 0,06 Kg

Net weight 0,04 Kg

Characteristics

Supervised

(FSK)

unsupervised

(OOK);

» Long-lasting lithium battery;

» SMD magnetic field sensor;

» Transmission frequency 433.92 MHz.

Sensor

Magnet

Lock

Product

2 6 8

Sensor

cover

2. Light conductor (LED)

Sensor

base

4. Screw hole for fixing

5. Magnet cover

6. Magnet base

7. Battery contact

Jumper

OOK/FSK

Sensor

aperture

access

the

XAS

Smart

and

XAS

Smart

Black

board

change

the

battery

change

the

FSK/OOK supervision, just remove the cover through the latch, it is not necessary to use

tools.This way the plate will be exposed and ready for handling.

CR2032

Remove the board, then insert the battery (model CR2032), respecting the polarity.

Enrolling the XAS Smart and XAS Smart

Black sensor

To register the XAS Smart and XAS Smart Black sensor code in the control panel,

follow the procedure below:

Insert the LITHIUM 3 Vdc battery - CR 2032, then type the command to register the

wireless device in the alarm center that will be used (Check the procedure in the

alarm center manual). Then perform a shot moving the magnet away from the sensor,

if the sensor is in a door for example, just open it observing if the LED will light up.

If the LED lights up, it indicates that there was a trip or transmission occurred, if the

LED does not light up, check the battery.

» Low battery sensor: the XAS Smart/XAS Smart Black has a battery level meter,

which measures the voltage and notifies you of the best time to change it, if the

sensor flashes the LED quickly in the opening, it indicates a low battery level. If

the alarm center is Intelbras, the sensor low battery warning will be indicated on

the product panel. The sensor sends low battery warning in both OOK and FSK

modulation.

OOK/F SK

XAS Smart and XAS Smart Black sensor

supervision setting

The XAS Smart/XAS Smart Black sensor allows you to select between supervised

(FSK) and unsupervised (OOK) modes. To switch between supervision modes, simply

remove the battery from the sensor, open the OOK/FSK jumper indicated on the bo-

ard (and then replace the battery), after which the sensor will operate in supervised

mode (FSK). Changing from supervised mode (FSK) to non-supervised mode (OOK) is

also simple, just remove the battery from the sensor, close the OOK/FSK jumper ter-

minals again and replace the battery, after which the sensor will return to operating

mode. unattended mode (OOK). Factory default: unsupervised (OOK)

In FSK modulation, the sensor transmits opening and closing and periodically super-

vises the sensor.

With Jumper OOK

No Jumper FSK

GAP

Installation

The XAS Smart / XAS Smart Black sensor can be attached using double-sided tape

or a screw. If the option with double-sided tape is chosen, clean the surface that will

be in direct contact with the tape and then stick it to the base of the product. If you

are going to use screws, just open the sensor and use the holes for passing the screw

located at the base of the product, as shown in the following figure.

Important: check if the GAP distance (distance between the sensor and the mag-

net) is within the specification, to avoid unwanted triggering in case of any vibration

in the structure where the sensor is installed.

Note: the type of surface where the sensor is installed may influence the distance

from the GAP.

» Opening GAP: 37 mm ±10%

» Closing GAP: 27 mm ±10%.

Aperte

para

travar

Figura 01

Figura 02

Pino

Aperte

para

travar

Press

lock

To close the sensor, check the pin located on the base, it must be positioned on the

same side as the battery, after positioning the base, just press it for locking, there is only

one way to close the sensor, check image 01 To close the magnet, just position the base

and press it, image 02.

Figure

The sensor must be installed according to the images below, with the magnet aligned

with the sensor body and with the smallest possible distance between them, so that

the magnet is in contact with the magnetic field sensor.

Note: for closing and opening the SMD magnetic field sensor, the distances from the

GAP must be respected.

Press

lock

Figure

Autres manuels pour XAS Smart

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intelbras Accessoires

Intelbras

Intelbras IVP 7001 MW EX Manuel utilisateur

Intelbras

Intelbras IVA 3070 X Manuel utilisateur

Intelbras

Intelbras IVP 7000 MW EX Manuel utilisateur

Intelbras

Intelbras IVA 3015X Manuel utilisateur

Intelbras

Intelbras IVA 5015 digital Manuel utilisateur

Intelbras

Intelbras IVP 2000 SF Manuel utilisateur

Intelbras

Intelbras IVP 3000 MW Manuel utilisateur

Intelbras

Intelbras XAS Light Manuel utilisateur

Intelbras

Intelbras IVP 8000 Pet Manuel utilisateur

Intelbras

Intelbras IVP 3000 CF Manuel utilisateur

Intelbras

Intelbras IVP 3011 Teto Manuel utilisateur

Intelbras

Intelbras iIVA 5040 AT Manuel utilisateur

Intelbras

Intelbras IVP 4000 smart Manuel utilisateur

Intelbras

Intelbras IVP 4000 smart Manuel utilisateur

Intelbras

Intelbras XAS 4010 SMART Manuel utilisateur

Intelbras

Intelbras IVP 1000 PET Manuel utilisateur

Intelbras

Intelbras IVP 3000 MW Manuel utilisateur

Intelbras

Intelbras IVP 7001 MW PET Manuel utilisateur

Intelbras

Intelbras IVP 3011 Cortina Manuel utilisateur

Intelbras

Intelbras IVP 1000 PET Manuel utilisateur

Intelbras

Intelbras XAS Smart Manuel utilisateur

Intelbras

Intelbras IVP 3021 SHIELD Manuel utilisateur

Intelbras

Intelbras IVP 5301 PET PRO Manuel utilisateur

Intelbras

Intelbras IVA 7100 Dual Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur