Intel NUC7i3BNHXF Manuel utilisateur
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
1
Intel® NUC Kit NUC7i3BNHX1 with Intel® Optane™ Memory
Intel® NUC Kit NUC7i5BNHX1 with Intel® Optane™ Memory
Intel® NUC Kit NUC7i7BNHX1 with Intel® Optane™ Memory
User Guide
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
2
Before You Begin
CAUTIONS
The procedures in this user guide assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance required for using
and modifying electronic equipment.
Disconnect the computer from its power source and from any telecommunications link or network before
performing any of the procedures described in this guide. Failure to disconnect power,
telecommunications links, or networks before you open the computer or perform any procedures can
result in personal injury or equipment damage. Some circuitry on the board can continue to operate
even though the front panel power button is off.
Follow these guidelines before you begin:
Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as model, serial numbers,
installed options, and configuration information.
Electrostatic discharge (ESD) can damage components. Perform the procedures described in
this chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam
pad. If such a station is not available, you can provide some ESD protection by wearing an
antistatic wrist strap and attaching it to a metal part of the computer chassis.
Installation Precautions
When you install and test the Intel NUC, observe all warnings and cautions in the installation
instructions.
To avoid injury, be careful of:
Sharp pins on connectors
Sharp pins on circuit boards
Rough edges and sharp corners on the chassis
Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
Damage to wires that could cause a short circuit
Observe all warnings and cautions that instruct you to refer computer servicing to qualified
technical personnel.
Observe Safety and Regulatory Requirements
If you do not follow these instructions, you increase your safety risk and the possibility of
noncompliance with regional laws and regulations.
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
3
This guide tells you how to:
•
Install and remove memory
•
Install an M.2 SSD
•
Install a 2.5” drive
•
Install a VESA mount bracket
•
Connect power
•
Install an operating system
•
Install the latest drivers
Open the Intel NUC Chassis
To open the Intel NUC chassis, follow these steps:
1. With a screwdriver unscrew the four corner screws on the bottom cover of the chassis and lift the
cover (using an electric or battery operated screw driver can damage the NUC).
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
4
Installing and Removing Memory
Intel NUC Kits NUC7i3BNHX1, NUC7i5BNHX1 and NUC7i7BNHX1 have two 260-pin DDR4 SO-DIMM
sockets. Be sure to select memory modules that meet these requirements:
1.2V low voltage memory
2133 MHz SO-DIMMs
Non-ECC
Find compatible memory modules in the Intel Product Compatibility Tool
NUC7i3BNHX1
NUC7i5BNHX1
NUC7i7BNHX1
NOTE
If you plan to install only one memory module, install it in the lower memory
socket.
To install memory, follow these steps:
1. Observe the precautions in "Before You Begin" on page 2.
2. Turn off all peripheral devices connected to the computer. Turn off the computer and
disconnect the power cord.
3. Remove the computer’s bottom chassis cover.
4. Align the small space at the bottom edge of the memory module with the key in the socket.
5. Insert the bottom edge of the module at a 45 degree angle into the socket (A).
6. When the module is inserted, push down on the outer edge of module until the retaining
clips snap into place (B). Make sure the clips are firmly in place (C).
To remove a SO-DIMM, follow these steps:
1. Observe the precautions in "Before You Begin" on page 2.
2. Turn off all peripheral devices connected to the computer. Turn off the computer and disconnect
the power cord.
3. Remove the computer’s bottom chassis cover.
4. Gently spread the retaining clips at each end of the memory socket, which causes the module to
pop out of the socket (C).
5. Holding the module by the edges, lift it away from the socket, and store it in an anti-static package.
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
5
6. Reinstall and reconnect any parts you removed or disconnected to reach the memory sockets.
7. Replace the computer’s cover and reconnect the power cord.
Install an M.2 SSD or Intel® Optane™ Memory Module
The Intel NUC Kits NUC7i3BNHX1, NUC7i5BNHX1 and NUC7i7BNHX1 support 80mm and 42mm SSDs.
Find compatible M.2 SSDs in the Intel Product Compatibility Tool
NUC7i3BNHX1
NUC7i5BNHX1
NUC7i7BNHX1
NOTE
Before changing the Intel Optane memory module, it needs to be disabled. Follow Removing
Intel Optane Memory on this page first, before taking the module out.
To Change an M.2 SSD:
1. Remove the small silver screw from the 80mm or 42mm metal standoff on the board (A).
2. Remove the pre-installed SSD/Intel Optane Memory from the connector.
3. Align the space at the bottom of the new M.2 SSD to the key on the connector.
4. Insert the bottom edge of the M.2 SSD into the connector (B).
5. Secure the card to the standoff with the small silver screw (C).
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
6
Install a 2.5” SSD or Hard Drive
The Intel NUC Kits NUC7i3BNHX1, NUC7i5BNHX1 and NUC7i7BNHX1 support an additional 2.5” Solid
State Drive (SSD) or Hard Disk Drive (HDD).
Find compatible 2.5” drives in the Intel Product Compatibility Tool:
NUC7i3BNHX1
NUC7i5BNHX1
NUC7i7BNHX1
1. Slide the new 2.5” drive into the drive bay, ensuring the SATA connectors are fully seated into the
connectors of the SATA daughter card (A).
2. Secure the drive into the drive bay with the two small silver screws that were included in the box (B).
Set the drive bay bracket down inside the chassis (C).
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
7
Close the Chassis
After all components have been installed, close the Intel NUC chassis (using an electric or battery
operated screw driver can damage the NUC).
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
8
Attach and Use the VESA Bracket (Optional)
Follow these instructions to attach and use the VESA mount bracket:
1. Using the four small black screws that were included in the box, attach the VESA bracket to the
back of the monitor or TV.
2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.
3. Slide the Intel NUC onto the VESA mount bracket.
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
9
Connect Power
Country-specific power plug attachments are included in the Intel NUC Kit box.
1. Choose the attachment for your region.
Plug
Code
US
UK
EU
AUS
Country
United States
United Kingdom
European Union
Australia
Plug
Code
CHN
IND
KOR
ARG
Country
China
India
South Korea
Argentina
Plug
Code
BRA
Country
Brazil
User Guide for NUC7i3BNHX1, NUC7i5BNHX1, NUC7i7BNHX1
10
2. Slide the attachment (B) onto the power plug, locking it into place (A).
3. Connect AC power.
Autres manuels pour NUC7i3BNHXF
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Intel Ordinateur de bureau
Intel
Intel NUC8 Home Manuel utilisateur
Intel
Intel NUC8i7HNK Manuel utilisateur
Intel
Intel NUC 13 Pro NUC13ANHi7 Manuel utilisateur
Intel
Intel NUC DN2820FYKH Manuel utilisateur
Intel
Intel Learning Series Manuel utilisateur
Intel
Intel NUC Series Manuel utilisateur
Intel
Intel BOXNUC8i7BEKQA Manuel utilisateur
Intel
Intel NUC6i3SYK Manuel utilisateur
Intel
Intel NUC7 Home Manuel utilisateur
Intel
Intel SR2600UR - Server System - 0 MB RAM Manuel utilisateur
Intel
Intel SR6850HW4 - Server Platform - 0 MB RAM Manuel utilisateur
Intel
Intel inside MINIS FORUM Manuel utilisateur
Intel
Intel NUC Kit DE3815TYKHE Manuel utilisateur
Intel
Intel NUC6CAY Instructions de montage
Intel
Intel TIGW1U - Carrier Grade Server Manuel utilisateur
Intel
Intel SC5650SCWS Manuel utilisateur
Intel
Intel NUC 8 Mainstream-G NUC8i5INH Guide de configuration
Intel
Intel Compute Stick STCK1A8LFC Manuel utilisateur
Intel
Intel NUC11BT Manuel utilisateur
Intel
Intel Classmate PC Manuel utilisateur
