Inovalley CH06 Manuel utilisateur

RETRO PORTABLE

CD/MP3 PLAYER

WITH RADIO USB/SD AND ALARM CLOCK

Ref.: CH06

- INSTRUCTION MANUAL -

IMPORTANT SAFETY INSTRUCTIONS:

1. Read the instructions. All uses guidelines must be read before start device.

2. Keep the instructions for future use.

3. Attention, use and security guidelines must be respected.

4. The device must not be used near water or be put in contact with moisture.

5. Make sure has no liquid is spilled on device and device openings.

6. Move device carefully, avoid shocks.

7. Do not block the breakdown of the device outputs.

8. Do not place the device near from a heat source (e.g. radiator). Do not expose it to the Sun.

9. Plug the device as indicate on this information form.

10. This device has a connection with overload protection (security device) decision-making. If the

replacement of decision-making is required, please you send has an experienced or the device

manufacturer technician.

11. For cleaning the device, please follow the recommendations of the notice.

12. The sector cord should be unplugged a long period of use.

13. Device shall be repaired by a qualified person when:

a. the taken or the power cord is damaged,

b. objects have fallen a I ' interior camera or a liquid was reverses a I ' internal device,

c. device was exposes to the rain,

d. device does not work correctly without notable exterior change,

e. device fell and the subwoofer is broken.

14. The user shall not try to maintain device beyond that which is described in this information form.

The guarantee would negate.

LOCATION OF CONTROLS

1) LEATHER HANDLE

2) ALARM FUNCTION BUTTON

3) SLEEP FUNCTION BUTTON

4) PRESET EQ BUTTON

5) VOLUME UP/DOWN KNOB

6) POWER ON/STANDBY BUTTON

7) FUNCTIONS SELECTOR BUTTON

8) MEMORY/ID3/CLOCK-ADJ BUTTON

9) PLAY MODE BUTTON

10) FLODER UP BUTTON

11) SKIP UP /DOWN BUTTON

12) TUNING KNOB

13) PLAY/PAUSE BUTTON

14) STOP BUTTON

15) DISPLAY / SNOOZE BUTTON

16) LCD DISPLAY

17) USB SOCKET

18) 3.5MM HEADPHONE JACK

19) SD CARD SLOT

20) CD DOOR OPEN/CLOSE

21) REMOTE SENSOR

22) DIAL POINTER

23) FM-STEREO LED INDICATOR

24) STANDBY LED INDICATOR

25) BAND / FM-MO/ST SELECTOR

26) ROD ANTENNA

27) AC SOCKET

28) BATTERY COMPARTMENT

29) CLOCK BACK-UP BATTERY

CAUTION:

USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

THIS UNIT SHOULD NOT BEADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.

PRECAUTIONS FOR USE

INSTALLATION

UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAIN VOLTAGE AND BEFORE ALL

OTHER CONNECTIONS HAVE BEEN MADE.

DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS AT

THE BACK OF THE UNIT FOR VENTILATION.

AC CONNECTION

1. CONNECT THE ONE END OF THE DETACHABLE POWER CORD TO THE AC SOCET (27) AND THE OTHER

END TO THE AC OUTLET.

2. WHEN YOU FIRST PLUG THE UNIT INTO THE MAINS, THE UNIT WILL GO INTO STANDBY MODE AND THE

STANDBY LED INDICATOR (24) WILL LIGHT UP, THE CLOCK AT LCD DISPLAY WILL SHOW AND START AT AM

12:00.

3. TURN ON THE POWER (6), IF THE LCD DISPLAY (16) IS ON WITH BACKLIGHTING, IT MEANS THE POWER

SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC.

DC CONNECTION

FOR DC OPERATION, PLEASE INSERT 6 PCS SIZE C (LR14) 1.5V BATTERY AT BATTER COMPARTMENT (28) AS

BELOW DIRECTION:

SETTING THE CLOCK

1. SET UNIT AT STANDBY MODE.

2. PRESS THE “ MEM/ID3/CLK-ADJ ” BUTTON (8) TO ENTER CLOCK ADJUST MODE. THE LCD DISPLAY (16)

WILL SHOW “ 12HR OR 24HR“. PRESS SKIP OR SKIP BUTTON (11) TO SELECT THE APPROPIATE

AREA HOUR FORMAT(12HR/24HR). PRESS “ MEM/ID3/CLK-ADJ ” BUTTON (8) AGAIN TO CONFIRM.

3. THE LCD DISPLAY (16) WILL DISPLAY THE FIRST TWO DIGIT OF “00” IS FLASHING. PRESS SKIP OR

SKIP BUTTON (11) TO SET THE CORRECT HOUR. PRESS “ MEM/ID3/CLK-ADJ ” BUTTON (8) TO STORE

THE CORRECT HOUR.

4. THE THIRD & FOURTH DIGIT OF “00” IS FLASHING, PRESS THE SKIP OR SKIP BUTTON (11) TO SET

THE CORRECT MINUTES. THEN PRESS“ MEM/ID3/CLK-ADJ ” BUTTON (8) TO STORE THE CORRECT

MINUTE.

TO AVOID THE RE-SET OF CLOCK FREQUENTLY WHEN USING DC OPERATION, PLEASE

INSERT 2 PCS AAA SIZE (LR03) 1.5V BATTERY AT THE CLOACK BACK-UP BATTERY

COMPARTMENT (29) IN THE DIRECTION AS BELOW DIRECTION:

REMARK : PULL DOWN THE RIBBON WHILE INSERT THE BATTERY, THIS CAN HELP TO RELEASE

IT EASIER WHEN CHANGING THE BATTERY IN THE NEXT TIME.

LISTENING TO RADIO

OPERATION

1. TURN ON THE POWER (6)AND PRESS THE FUNCTION BUTTON (7) TO SELECT TUNER MODE.

2. SELECT THE DESIRE RADIO BAND (AM OR FM) AT “ BAND “ SELECTOR (25).

3. TURN THE TUNING KNOB (12)TO SET THE STATION FREQUENCYAS DESIRED.

4. ADJUST VOLUME KNOW (5) TO THE DESIRED VOLUME LEVEL.

HINTS FOR BEST RECEPTION:-

- AM : THE RECEIVER HASA BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY ROTATE OR

RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THEAM RECEPTION.

- FM : THE RECEIVER HAS RODANTENNA (26) HANGING AT THE REAR CABINET. THIS WIRE SHOULD BE

TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.

FM & FM-STEREO RECEPTION

IF STEREO SIGNAL IS BEING RECEIVED, THE STEREO LED INDICATOR (23) WILL LIGHT UP TO SHOW FM

STEREO PROGRAM IS NOW RECEIVING & VICE VERSA

PLAYING COMPACT DISC

GETTING START

1. PRESS FUNCTION BUTTON (11) TO SELECT “ CD ” MODE,

2. PRESS “ CD DOOR OPEN/CLOSE ” (20) TO OPEN THE CD DOOR.

3. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR BY

PRESSING THE “ CD DOOR OPEN/CLOSE “ (20)AGAIN.

4. FOCUS SEARCH IS PERFORMING, THE LCD DISPLAY (16) WILL SHOW THE TOTAL NUMBER OF TRACKS &

TOTAL PLAYING TIME.

PLAY / PAUSE MODE

1. PRESS THE “ PLAY/PAUSE ” BUTTON (13) TO START PLAYBACK, THE FIRST TRACK WILL START

PLAYBACK.

2. TO INTERRUPT, PRESS THE “ PLAY/PAUSE ” BUTTON (13) ONCE, AND THE PLAYING TIME WILL BE

FREEZE ON THE LCD DISPLAY (16). PRESS AGAIN TO RESUME NORMAL PLAYBACK.

STOP MODE

1. IF “ STOP ” BUTTON (14) IS PRESSED DURING PLAY OR PAUSE MODE, SYSTEM WILL GO TO STOP

MODE.

SKIP MODE (SKIP UP / SKIP DOWN )

1. DURING PLAY OR PAUSE MODE, IF “SKIP UP ” BUTTON (11) IS PRESSED. IT WILL GO TO NEXT TRACK

AND DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.

2. DURING PLAY OR PAUSE MODE, IF “SKIP DOWN ” BUTTON (11) IS PRESSED. IT WILL GO BACK TO THE

BEGINNING OF THE TRACK, ORIGINALTRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE MODE.

3. AFTER STEP 2, PRESS “SKIP DOWN ” BUTTON (11) AGAIN WILL GO TO THE PREVIOUS TRACK AND

REMAIN THE PLAY OR PAUSE MODE.

FOR MP3 DISC

1. AFTER FOCUS SEARCH IS PERFORMING, THE TOTAL NUMBER OF TRACK AND ALBUM WILL BE SHOWN

ON THE LCD DISPLAY (16).

2. PRESS “ FOLDER UP OR DOWN “ BUTTON AT REMOTE CONTROL TO SELECT THE FOLDER

NUMBER.

3. PRESS “ SKIP UP “ OR SKIP DOWN (11) BUTTON TO SELECT THE TRACK NUMBER.

4. WHEN THE DESIRED TRACK AND FOLDER IS BEING SELECTED, PRESS THE “ PLAY/PAUSE ” BUTTON

(13) TO START PLAYBACK.

ID3 (TRACK/ALBUM TITLE) FUNCTION (BY REMOTE HANDSET)

DURING THE PLAYBACK OF MP3 TRACK, PRESS THE “ MEM/ID3/CLK-ADJ ” BUTTON (8) AND THE LCD DISPLAY

(16) WILL SHOW THE SONG TITLE / ARTIST NAME / ALBUM NAME IN ORDER ONCE TIME.

REMARK:-

- IN THAT CASE OF NO NAME OR NOT SUPPORTIVE LANGUAGES HAD BEEN ASSIGNED FOR THE MP3 TRACK,

“ NO INFO “ WILL SHOW ON LCD DISPLAY (16) WHEN PRESS THE “ ID3 “ BUTTON (8).

- NO TITLE/ALBUM NAME CAN BE RECOGNIZED IF THE INPUT FORMAT ON THE DISC/MASS MEDIA IS NOT

SUPPORTING BY THE SYSTEM.

- THE SYSTEM SUPPORT ONLY ENGLISH AND ARABIC NUMBER FOR ID3 FUNCTION

MP3 TRACK FORMAT REQUIREMENT:-

- BIT RATE : 32 KBPS~320KBPS, SAMPLING RATE : 32KHZ, 44.1KHZ AND 48 KHZ DECODABLE

- THE PERFORMANCE OF PLAYING MP3 DISC IS VARIOUS FROM THE QUALITY OF RECORDING DISC AND

THE METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP3-CD IS LONGER

THAN NORMAL CD DUE TO DIFFERENCE FORMAT.

REPEAT/INTRO/RANDOM MODE (BY REMOTE HANDSET)

PRESS THE “ PLAY MODE “ BUTTON DURING PLAYBACK TO SELECT REPEAT AND RANDOM FUNCTION, A

SINGLE TRACK, SINGLE FOLDER (MP3 ONLY) OR ALL THE TRACKS CAN BE PLAYED IN DIFFERENCE MODE AS

FOLLOW:-

FOR CD

(1) REPEAT 1 (2) REPEAT ALL TRACK (3) RANDOM (4) OFF MODE

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT 1 TRACK

REPEAT ALL

RANDOM RAN

OFF MODE --------------

FOR MP3/WMA DISC/FILE

(1) REPEAT 1 (2) REPEAT 1 FOLER (3) REPEAT ALL TRACKS

(5)OFFMODE (4)RANDOM

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT SINGLE TRACK

REPEAT SINGLE FOLDER AND

REPEAT ALL TRACKS

RANDOM MODE RAN

OFF MODE -----------------

REPEAT PLAY

YOU CAN LISTEN THE DESIRED TRACKS OR FOLDER REPEATEDLY BY THIS FUNCTION.

RANDOM PLAY

YOU CAN LISTEN ALLTHE TRACKS OR FOLDER IN A RANDOM ORDER BY THIS FUNCTION

CD / MP3 DISC PROGRAMMING (BY REMOTE CONTROL)

UP TO 20 TACKS CAN BE PROGRAMMED FOR DISC PLAY IN ANY ORDER. BEFORE USE, BE SURE TO PRESS

THE “ STOP ” BUTTON (14).

1. SET IN CD MODE & STOP THE CD PLAYBACK.

2. PRESS THE “ MEM/ID3/CLK-ADJ ” BUTTON (8), “ PROG “ WILL APPEAR & FLASHING ON LCD DISPLAY (16).

MOREOVER, IT WILL INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED – “ 0

P-01 “.

3. SELECT A DESIRED TRACK BY PRESSING SKIP UP OR DOWN BUTTONS (11).

4. PRESS THE“ MEM/ID3/CLK-ADJ ” BUTTON (8) TO STORE THE TRACK INTO MEMORY.

5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONALTRACKS INTO THE MEMORY IF NECESSARY.

6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS “ PLAY/PAUSE ” BUTTON (13)

TO PLAY THE SONG IN ASSIGNED ORDER.

7. PRESS THE “ STOP “ BUTTON (14) TO TERMINATE PROGRAM PLAY.

AFTER PROGRAM COMPLETE, PRESS “ MEM/ID3/CLK-ADJ ” BUTTON (8) TO REVIEW THE TRACKS BEING

PROGRAMMED.

PRESS “ STOP “ BUTTON (14) AT CD STOP MODE TO CANCEL ALL PROGRAMMED MEMORY UNTIL THE

“ PROG “ INDICATOR DISAPPEAR ON LCD DISPLAY (16).

FOR MP3 DISC / FILE, PRESS THE “ FOLDER UP “ BUTTON (10) TO SELECT THE 1ST TRACK OF NEXT

FOLDER DIRECTLY AND HENCE TO SPEED UP THE SONG SLECTION.

PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD

CONNECTING

THE SYSTEM IS ABLE TO DECODEAND PLAYBACK ALLMP3 /WMA FILE WHICH STORED IN THE MEMORY

MEDIA WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.

1. SET THE SYSTEM AT STANDBY MODE FIRST OR OTHER FUNCTION

EXCEPT SD OR USB MODE.

2. PLUG-IN THE USB PEN-DRIVE WITH THE FACE UP & MAKE SURE IT

GOING INTO COMPLETELY OR INSERT THE MEMORY CARD IN THE

DIRECTION OF THE ARROW AS SHOWN IN THE LABEL ON THE

UNDERSIDE OF THE MEMORY CARD SLOT COVER. INSERT STRAIGHT

WITHOUT BENDING.

CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD

DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB THUMB

DRIVE / SD/MMC CARD). CHECK TO BE SURE THE DIRECTION IS

CORRECT BEFORE CONNECTION.

3. PRESS FUNCTIONS BUTTON (7) TO “ “ SD CARD MODE OR “

“ USB MODE.

4. THE SYSTEM WILL START READING THE STORAGE MEDIAAUTOMATICALLYAFTER CONNECTING, AND

LCD DISPLAY (16) WILL SHOW THE TOTAL NUMBER OF MP3/WMA FILES BEING DETECTED.

5. REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC AS ABOVE.

REMARK

- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 OR WMA FORMAT ONLY AT USB/SD MODE

BUT NOT OTHER MUSIC FILE FORMAT.

- IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING

FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS NOT A

MALFUNCTION OF THE SYSTEM.

- USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED

FOR COMMUNICATION WITH COMPUTER DIRECTLY

REMOVING OF USB / MEMORY CARD

TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO EITHER

CD OR TUNER MODE FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY, FOR

MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD BEING PARTIALLY

EJECT AND YOU CAN REMOVE IT BY HAND.

MORE FEATURES

A. SLEEP SETTING

1. PRESS “ SLEEP ” BUTTON (3)AND SLEEP INDICATOR “ “ SHOWN ON THE LCD DISPLAY (16).

2. KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90 > 80 > 70 > …..>10

MINUTES RESPECTIVELY.

3. SYSTEM WILL STOPAND GOTO STANDBY MODE AUTOMATICALLYAFTER THE SELECTED TIMING.

4. TO CANCELTHE SLEEP MODE, PRESS “ SLEEP ” BUTTON (3) UNTIL THE “ “ INDICATOR DISAPPEAR ON

LCD DISPLAY (16).

REMARK:-

IF PRESS THE SLEEP BUTTON ONCE AND THE “ “ INDICATOR APPEAR ON THE LCD (16), THE SYSTEM

WILL GOTO STANDBY MODEAUTOMATICALLY AFTER SELECTED MINUTES.

B. ALARM CLOCK SETTING

THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY

CD/TUNER/USB/SD OR BUZZER SOUND RESPECTIVELY.

FIRST, SET THE UNIT AT STANDBY MODE. THEN PRESS AND HOLD THE “ ALARM ” BUTTON (2) FOR FEW

SECONDS TO ENTER THE SETTING MODE, THE LCD DISPLAY (16) WILL SHOW “ ON TIME : AND THEN FIRST

TWO DIGITS OF CLOCK WILL FLASHING:-

1) WAKE UP TIME : PRESS SKIP UP /DOWN “ BUTTON (11) TO SET THE HOUR & THEN PRESS

“ ALARM “ BUTTON (2) AGAIN TO CONFIRM. THEN PRESS SKIP UP /DOWN “ BUTTON (11) TO SET THE

MINUTES.

2) WAKE UP SOURCE : PRESS THE “ ALARM “ BUTTON (2) TO ENTER THE SOURCE MODE, PRESS SKIP

UP /DOWN “ BUTTON (11) TO SELECT CD, USB. SD. TUNER OR BUZZER MODE RESPECTIVELY.

3) WAKE UP VOLUME : PRESS THE “ ALARM “ BUTTON (2) TO ENTER THE VOLUME SETTING MODE, THEN

PRESS SKIP UP /DOWN “ BUTTON (11) TO PRE-SET THE WAKE UP VOLUME LEVEL.

AFTER SELECTING THE TIME/SOURCE/VOLUME, PRESS AGAIN THE “ ALARAM “ BUTTON (2) TO CONFIRM THE

SETTING.

REMARK:-

THERE ARE ABOUT 5 SECONDS FOR ALARM SETTING MODE, THIS SYSTEM WILL RETURN TO NORMAL

MODE AUTOMATICALLY IF NO KEYS BEING PRESSED IN THIS TIME FRAME.

ACTIVE/DE-ACTIVE TIMER FUNCTION

1. TO ACTIVE THE TIMER, PRESS THE “ALARM” BUTTON (2) AT STANDBY MODDE UNTIL THE TIMER

INDICATOR “ ” IS SHOWN ON LCD DISPLAY (16).

2. TO CANCEL ALARM FUNCTION BY PRESS AGAIN “ ALARM ” BUTTON (2) UNTIL THE TIMER INDICATOR

“” DISAPPEAR ON LCD DISPLAY (6).

REMARK:-

DURING THE ALARM ON MODE, PRESS THE “ ALARM “ OR “ POWER ON/STANDBY “ BUTTON WILL SWTICH

OFF THE SYSTEM.

IF THERE IS NO MUSIC SOURCE BEING DETECTED (SUCH AS CD, USB OR SD) WHEN THE PRESET TIME IS

REACHED, SYSTEM WILL DEFULT TO “ BUZZER “ MODE FOR WAKE UP MODE AUTOMATICALLY.

FOR TUNER WAKE UP, THE SYSTEM WILL PRESET AT THE LATEST RADIO FRQUENCY BEING LISTENED

BEFORE SWITCHING OFF.

SNOOZE FUNCTION

DUEING THE ALARM ON MODE, PRESS “ SNOOZE “ BUTTON (15) ONCE TO TERMINATE THE ALARM MODE

TEMPORARILY, AND SYSTEM WILL RE-START AGAIN AFTER 10 MINUTES ON EACH PRESS. TO CANCEL THE

ALARM, PRESS THE “ ALARM “ (2) BUTTON OR POWER ON/STANDBY BUTTON (6) WHILE SYSTEM IS ON.

C. PRE-SET EQ FUNCTION (BY REMOTE CONTROL)

THIS UNIT PROVIDES 4 DIFFERENCES SOUND MODE TO ENHANCE YOUR LISTENING EXPERIENCE. YOU CAN

SELECT THE DESIRED EFFECT BY PRESSING THE “ PRESET EQ” BUTTON REPEATEDLY AT FOLLOWING

SEQUENCE:-

FLAT JAZZ ROCK CLASSIC POP

D. DISPLAY FUNCTION

FOR CONVERIENCE USAGE, PRESS “ DISPLAY/SNOOZE “ BUTTON (15) WHEN SYSTEM IS ON AT ANY MODE,

THE LCD DISPLAY (16) WILL SHOW THE CURRENT TIME.

REMOTE CONTROL TRANSMITTER

BATTERY INSTALLATION (BATTERY NOT PROVIDED)

THE INFRA-RED TRANSMITTER REQUIRE 2 PCS “ AAA “ BATTERY FOR OPERATION

CONTROL FUNCTIONS & BUTTON DESCRIPTION

SNOOZE/DISPLAY PRESS TO TERMINATE THE ALARM TEMPORARILY

(10MINUTES)

PRESS TO SHOW THE CURRENT TIME DURING

CD/USB/SD PLAYBACK MODE RESPECTIVELY.

FUNCTION PRESS TO SELECT THE FUNCTIONS

(CD/SD/USB/TUNER)

ON/STANDBY PRESS TO SWITCH ON/STANDBY THE SYSTEM

SKIP UP /DOWN IN CD/USB/SD MODE : PRESS TO SELECT

PREVIOUS / NEXT TRACK OR

PRESS & HOLD TO PERFORM FAST

FORWARD/BACKWARD FUNCTION

IN ALARM SETTING MODE : PRESS TO SELECT

DIFFERENCE SETTING

PLAY/PAUSE IN CD/USN/SD MODE : PRESS ONCE TO START

PLAYBACK AND PRESS AGAIN TO STOP

PLAYBACK TEMPORARILY

FOLDER UP /DOWN IN USB/SD MODE : PRESS TO SKIP UP/DOWN

THE MP3 FOLDER

STOP IN CD/USB/SD MODE : PRESS TO TERMINATE

PLAYBACK OR CANCEL PROGRMMED TRACKS

MEM/ID3/CLK-ADJ IN CD/SUB/SD MODE : PRESS TO ACTIVE

PROGRAM FUNCTION

IN USB/SD PLAYBACK MODE : PRESS TOACTIVE

ID3 FUNCTION

IN STANDBY MODE : PRESS TO ADJUST THE CLOCK

PLAY MODE PRESS TO ACTIVE REPEAT/RANDOM FUNCTION

SLEEP PRESS TO ACTIVE SLEEP FUNCTION

VOLUME -/+ PRESS TO ADJUST VOLUME LEVEL UP/ DOWN

PRESET EQ PRESS TO SELECT DIFFERENCE EQ MODE

DETAILS AND PRECAUTIONS ON THE USE OF BATTERIES :

- Discard a used battery in nature or garbage pollutes and prevents the recovery of recyclable materials.

It is therefore important to limit consumption of batteries and follow these guidelines:

focus on alkaline batteries (that last longer than the saline batteries) and when possible, rechargeable

batteries

deposit batteries and accumulators in specific containers arranged among traders.

For example, metals will be valued and polluted the environment because they contain heavy metals

hazardous to health and the environment primarily (cadmium and nickel)

- The piles must installation by respecting the polarity indicated on the apparatus and the pile.

An incorrect positioning can is to damage the apparatus, is to cause escapes on the level of the pile, is to the extreme to

cause a fire or the explosion of the pile.

- To ensure proper operation, the batteries must be in good condition. In case of abnormality in the functioning of the

device, put fresh batteries

- Never attempt to recharge non-rechargeable batteries. They could run, warm up, causing a fire or explosion.

- Replace all batteries at the same time. Never mix zinc batteries with alkaline batteries or rechargeable batteries

- The batteries must be removed from the device

- Also, remove the batteries from your device if you do not use it for a long time, if the batteries may leak and cause

damage.

- Never try to short-circuit the battery terminals

- Never dispose of batteries in fire, they might explode

- Charging of batteries is to be performed by an adult.

- Remove batteries from the device before reloading.

- We recommend an adult to supervise children when they change the batteries so that these instructions are complied

with or to make himself the replacement of batteries.

- If a battery is swallowed, immediately consult a doctor or poison control center nearest you.

Do not forget to carry the product with you

Table des matières

Autres manuels Inovalley Lecteur MP3

Inovalley

Inovalley MP61 Manuel utilisateur

Manuels Lecteur MP3 populaires d'autres marques

Blaupunkt

Blaupunkt Compact Drive MP3 Manuel utilisateur

Memorex

Memorex MMP9008 - 8GB USB 2.0 Manuel utilisateur

Meizu Electronic Technology

Meizu Electronic Technology E5 Manuel utilisateur

Naxa

Naxa NMV-173NX Manuel utilisateur

Philips

Philips PSA250 Manuel utilisateur

Zipy

Zipy go! Waving Manuel utilisateur

Sylvania

Sylvania SMPK4068 Manuel utilisateur

Sony

Sony NW-MS7 - Memory Stick Walkman Manuel utilisateur

Irradio

Irradio RF-42UC Manuel utilisateur

NABAIJI

NABAIJI SWIM MUSIC 100 Manuel utilisateur

Laser

Laser MP3-A9-4GB Manuel utilisateur

Samsung

Samsung YP-T7F Manuel utilisateur

Savant

Savant SMS-1001-00 Guide de référence rapide

Trevi

Trevi XP 71 BT Manuel utilisateur

AGPtek

AGPtek C2 Manuel utilisateur

MobiBlu

MobiBlu DAH-1500i Manuel utilisateur

Denver

Denver MPS-201 Manuel utilisateur

Steren

Steren MP3-002 Manuel utilisateur