Inosmart BT 600 Manuel utilisateur

OPERATION MANUAL

Bluetooth

Revision 25, 11.10.2023

min. reader firmware 1.6.184

min. control unit firmware 1.0.42

min. application version v3.1.54

Dear User,

Thank you for choosing to purchase a fingerprint reader that

will allow you to enter your home or business quickly and

easily. Your reader can be used to open the door using a

fingerprint, smartphone or numeric code (keyboard reader

model).

Although our readers are easy to use, please take a few minutes

to read the instructions below. We have prepared all the information you need to pay attention to both for the first

time and for subsequent use. For easier understanding, you can also visit our website www.inosmart.info/bt and

watch the attached video content about the operation and use of the fingerprint reader.

The instructions are uniform for all modules: BT 600, BT 610, BT 620, BT 630, BT 640, BT 660 and BT 670.

We wish you pleasant and simple use.

 
 
 
TABLE OF CONTENTS 
GLOSSARY ........................................................................................................................1 
INOSMART BIOMETRIC MODULES (READERS) - FUNCTIONS ..............................................2 
FIRST USE .........................................................................................................................4 
READER –CONTROL..........................................................................................................5 
CONTROL VIA THE CONTROL UNIT ....................................................................................5 
ADD FINGERPRINT OF ANEW USER ....................................................................................................5 
 ............................................................................................................................................................6 
ADD NEW CODE NUMBERS (MODULES BT 600, BT 610, BT630, BT660 AND BT 670)..............................6 
RESET TO FACTORY DEFAULTS ..........................................................................................7 
READER –SECURITY LOCK.................................................................................................7 
 CONTROL VIA A SMARTPHONE ..............................................................................8 
ESTABLISH FIRST CONNECTION BETWEEN READER AND SMARTPHONE.............................8 
MAIN MENUS................................................................................................................. 12 
USER..................................................................................................................................................13 
 ADD NEW FINGERPRINT...............................................................................................................16 
ADD NEW CODE NUMBERS (modules BT 600, BT 610, BT630, BT660 and BT 670) .....................18 
TIMER................................................................................................................................................19 
 FREE ACCESS.................................................................................................................................20 
SETTINGS...........................................................................................................................................21 
EVENT HISTORY.................................................................................................................................22 
THE MOST COMMON REASONS FOR POOR FINGERPRINT RECOGNITION........................................23 
DOOR OPENING VIA BLUETOOTH CONNECTION.............................................................. 25 
SECOND RELAY............................................................................................................... 28 
CONECTION WITH AN ADDITIONAL TELEPHONE.............................................................. 29 
PAIR READER WITH RADIO BELL...................................................................................... 30 
CARE AND MAINTENANCE .............................................................................................. 31 
ERROR MESSAGES .......................................................................................................... 31 
RESET TO FACTORY SETTINGS ......................................................................................... 32 
INOSMART READER SPECIFICATIONS .............................................................................. 34 

WIRING DIAGRAM.......................................................................................................... 36

USER INSTRUCTIONS ...................................................................................................... 37

MANUFACTURER WARRANTY......................................................................................... 37

GLOSSARY

•BT module –Inosmart biometric module, a reader built into the outside of the sash or door

handle. Allows you to open the door using your fingerprint, smartphone or keyboard.

•Fingerprint sensor - enables identification of your fingerprint. It is built into the reader.

•Control unit - enables el. communication between the sash, the door frame and the

Inosmart reader. It is built into the side part of the door leaf.

•WiFi –wireless communication - Allows you to connect your smartphone and the Inosmart

reader.

•LED –light emitting diode. An electronic component that emits light.

•Administrator fingerprint –one of the 3 fingerprints you entered when using the reader for

the first time.

•Placing a finger - the user places his finger on the fingerprint sensor built into the reader.

•Relay - is an electromagnetic switch that you turn on with the control voltage

INOSMART BIOMETRIC MODULES (READERS) - FUNCTIONS

BT 600, BT 630

BT 610, BT660 and BT670

BT 620

•Fingerprint sensor

•Keyboard

•Bluetooth

•Bell

•Signal lights

•Buzzer

•Fingerprint sensor

•Keyboard

•Bluetooth

•Signal lights

•Buzzer

Fingerprint sensor

Bluetooth

Signal lights

Buzzer

NFC

CODE KEYBOARD

FOR ENTERING

CODE NUMBERS

BELL

FINGERPRINT SENSOR

MULTICOLOR

SIGNAL LEDs

CONTROL UNIT –FUNCTIONS

The fingerprint reader can be controlled using the buttons on the control unit installed in

the door leaf.

KEY 1

Adding a new fingerprint, smartphone or code number.

KEY 2

Removing a fingerprint, smartphones or code numbers.

KEYS 2 + 3

Registration of three administrator fingerprints. Without three registered administrator fingerprints,

the unit cannot be put into operation. To enroll the three administrator fingerprints, press buttons 2

and 3 simultaneously.

If administrator fingerprints are already registered, pressing this key combination deletes them and

registers the new fingerprints.

KEY 3

Activation of the Bluetooth connection.

KEYS 1 + 2 + 3 (10 seconds)

The control unit is reset to the factory settings. All data will be deleted!

KEYS 2+3 (5 SECONDS)

By pressing the 2+3 keys, you initiate the deletion of already entered administrator fingerprints that you release with the

existing administrator fingerprint.

The reader immediately requires the entry of 3 new administrator fingerprints, these are registered in the application

under an undefined user.

The ADMINISTRATOR is responsible for managing the fingerprint reader. Up to three different fingerprints / persons can be

determined on first use - e.g. B. a person with three fingerprints or three different people with one fingerprint each. At least

two people are recommended for practicality and safety.

Unlike the other users, an administrator has full access to the reader and the control unit and can add new users, fingerprints,

smartphones or code numbers and also remove them.

As long as the reader's memory is empty, anyone can register as an administrator with their fingerprints. An administrator

should therefore be appointed immediately when the device is commissioned to prevent any misuse.

FIRST USE

ADMINISTRATOR FINGERPRINT

Before using the Inosmart BT module (reader) for the first time, one or more

administrators must be specified. All subsequent changes, entries etc. require

confirmation by the administrator.

Before using the reader, three administrator fingerprints must be stored.

This step is essential before the first use.

Make sure the fingerprints are read correctly; the fingertip should cover at least

70% of the sensor.

The administrator has access to all security-related functions with his fingerprint. For this reason, at least two

administrators are recommended.

To add an administrator, proceed as follows:

PRESS BUTTONS 2 AND 3 ON THE CONTROL

UNIT AT THE SAME TIME.

The reader's two LEDs light up white.

READ THE FINDERPRINT OF THE RESPECTIVE

ADMINISTRATOR THREE TIMES.

Administrator 1: read in the fingerprint

three times

Administrator 2: read in the fingerprint

three times

Administrator 3: read the fingerprint

three times

Make sure that the entire fingertip

rests on the reader. The fingertip

should cover at least 70% of the

sensor.

After the administrator fingerprints have been

successfully stored, the two LEDs light up blue.

THE READER IS READY TO OPERATE.

You can also find a corresponding tutorial on our homepage www.inosmart.info/bt.

READER –CONTROL

The fingerprint reader can be controlled via the control unit or via the Inosmart app (smartphone).

Users, smartphones or code numbers can be added and deleted via the buttons on the control unit.

The Inosmart app enables central management of the device and all registered users - adding and removing

users, smartphones or code numbers, creating timers and detailed management of other access authorizations.

CONTROL VIA THE CONTROL UNIT

The three buttons on the control unit can be used to control the following main functions of the reader:

adding or removing fingerprints, NFC smartphones and code numbers (on models with a code pad).

ADD FINGERPRINT OF A NEW USER

PRESS BUTTON 1 ON THE CONTROL

UNIT.

The reader beeps briefly and both LEDs flash

green.

Put administrator's fingerprint on

the sensor to authorize adding a new

user's fingerprint.

A new fingerprint is approved.

The LEDs light up white.

Read the new user's fingerprint three

times via the sensor.

If this was successful, the LEDs light

up green, otherwise red.

The reader beeps briefly and both LEDs light up

green.

A NEW USER HAS BEEN ADDED SUCCESSFULLY.

The reader is ready for operation and both LEDs

light up blue.

The control unit does not allow controlling the lights, creating timers, naming users or managing access rights.

Each time it is used, the reader compares the fingerprint with the one stored and also saves any new properties that have

been identified. This means that individual fingerprint recognition is constantly improving over time. The system is able to

store and automatically update up to 20 fingerprint variations for each individual user.

ADD NEW CODE NUMBERS (modules BT 600, BT 610, BT630, BT660 and BT 670)

The BT 600, BT 610, BT630, BT660 and BT 670 modules have a code keypad that can be used to

open the door with a code number. The length of the code is pre-programmed at the factory to 4 digits. To

add a new code number, please proceed as follows:

PRESS BUTTON 1 ON THE CONTROL

UNIT.

The reader beeps briefly and both LEDs flash green.

Place the administrator's fingerprint on

the sensor to authorize the addition of

a new numeric code.

A new code number is approved.

The LEDs light up white.

Enter the four-digit code number.

The reader beeps briefly and both LEDs light up green.

A NEW CODE NUMBER WAS SUCCESSFULLY ADDED.

The reader is ready for operation and both LEDs light up

blue.

The skin, and thus also the fingertips, is subject to constant changes (different moisture content of the skin

at different times of the year, injuries to the skin, etc.) and at the same time no two sensor operations are

the same. For this reason, advanced sensors with 360° recognition are built into our fingerprint readers,

which counteract these problems and correctly recognize every fingerprint at any angle.

The length of the code number - from 4 to 10 digits - can be set via the Inosmart app.

If no code number was entered, the code keyboard is not functional, which is indicated by the LEDs and a beep. After

entering the first code number, the keyboard is ready for use.

Ce manuel convient aux modèles suivants

Table des matières

Manuels Système RFID populaires d'autres marques

Chainway

Chainway R1 Manuel utilisateur

IFM

IFM DTC600 Manuel utilisateur

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manuel utilisateur

RHOMBUS

RHOMBUS DR20 Manuel utilisateur

Sirit

Sirit IDentity 6204 Manuel utilisateur

SOREX

SOREX FLEX Manuel utilisateur

Omron

Omron V780-HMD68-EIP-KR Manuel utilisateur

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instructions d'utilisation

Shuttle

Shuttle BR06 Instructions d'utilisation

Digilock

Digilock Curve Keypad Basic Manuel utilisateur

Atid

Atid AT870 Manuel utilisateur

Chacon

Chacon 34958 Manuel utilisateur

Paxton

Paxton PROXIMITY architectural reader Manuel utilisateur

CipherLab

CipherLab 1800 series Manuel utilisateur

Brady

Brady FR22 Manuel utilisateur

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manuel utilisateur

Unitech

Unitech RH767 Manuel utilisateur

Honeywell

Honeywell 026366.00 Manuel utilisateur

inosmart BT 600 Manuel utilisateur

Manuels Système RFID populaires d'autres marques