FUNCTION button
Volume UP
DC USB in
Power Button (on/off)
Auxiliary Audio
LED Indicator
Volume DOWN
Power on/off
1. Turn on the Speaker by on/off- switch on lower right.
Function key ( Bluetooth® Activation button )- Pairing
2. Hold the function key about 5 seconds, the Red/Blue indicator LED on
the front will flash. You will also hear a “BEEP” indicating that the Jukebox
Wizard is ready for pairing with your device. As the Bluetooth® discovers
your device look for the speaker’s name: “Jukebox Wizard”.
And pairing with your mobile can begin.
(after 10 minutes, if no pairing or AUX not connect with any cable, unit will
automatically into STANDBY mode)
3. If a password is required for your device, use the password “0000”and
choose for connecting “XXXXXX”, After pairing is finished the front LED
changes from Red/Blue flashing to only Blue flashing
Important notice：Above is the typical hands-free Bluetooth® pairing
instructions, and it may vary with different mobile phone models. For more
information, please refer to the user manual or contact the mobile phone’s
manufacturers.
5. Play music - open the phone’s music player after pairing and connecting.
Press the Bluetooth logo function key to pause music during playing music,
and press again to resume.
Important Notice：Some phones need to manually connect Jukebox
Wizard, in this case, you need to manually select the "Play via Bluetooth®
*(Because of differences in phone models, please refer to the mobile
phone user manual for accessing to music through Jukebox Wizard).
4. Function Key (Bluetooth® Activation button) - Previously Paired
If you have previously paired the Jukebox Wizard to your device just hold
down the function key until the RED light is “ON”.
Your phone or audio device will show you “Bluetooth® connection is
successful or ask for permission to accept connection- choose ”yes”.
Functions
How To Operate
The Jukebox Wizard has a 3.5 mm audio input plug. It can be used with
other MP3, iPod, CD players and other audio players to transmit audio
signals. Connect your audio player with the required audio cable. At this
point the device can be connected to the maximum volume setting, and
then use the system to adjust its volume buttons.
Note: If the system is set to 80％volume, a fully charged battery sustainable supply for about 5-7
hours. However, the battery discharge rate is due to the music type and volume setting. Decreasing
the volume can greatly extend the battery life.
Other Audio Sources
LED states:
a) Pairing--- red and blue LED flashes and ‘BEEP’ tone when ready for paring
b) Bluetooth® mode---Blue LED flashes slowly
c) AUX mode--- LED only light up in permanent Red
d) no signal received---LED flashes red slowly
e) ON--- solid red
AUX
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses an can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is not guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
