InnoMedia IPBX-400 Manuel utilisateur

InnoMedia

iPBX-400

Quick Install Guide

www.innomedia.com

Table of Contents

Introduction 2

Package Contents 2

Installation 3

Wall-Mounting Instructions 5

Troubleshooting 6

Appendix A. LED Status Summary 7

Specications 7

Federal Communication Commission Interference State-

ment 8

Introduction

The InnoMedia iPBX comes with all the IP-PBX features you’d expect and SIP Trunking,

the industry-accepted approach for direct IP peering to VoIP Service Providers. With SIP

Trunking enabled, the iPBX is capable of managing in a secured manner, an enterprise’s

telephony network.

Package Contents

The InnoMedia iPBX-400 comes with the following items:

1 iPBX

1 RJ-45 Cable

2 RJ-11 Phone Cables

1 AC/DC Power Adapter

1 Quick Install Guide

1 Battery Backup Supply

1 Wall-Mounting Template

1 CD

CAUTION

Disconnect power adapter from the equipment before removing the cover of the

battery compartment.

Installation

1. Connect the RJ-45 cable to the “WAN”connector.

2. Connect a grounding cable to be connected to the ground screw terminal as shown

in the diagram.

3. Connect any standard analog telephone or fax machine to iPBX’s “PHONE” connec-

tor, labeled 1-4.

4. Connect your PC to any LAN port using included RJ-45 cable.

5. Connect included AC power cable to the electrical outlet and its cable to the “12V

DC” connector.

6. Optionally, open the battery compartment and insert the battery. Put the cover back

in place.

7. Power on iPBX-400. If you have analog phones that are connected to iPBX-400

Phone interface, you may start placing and receiving telephones with the default

extension numbers, from 400 to 403.

8. Please refer to the administrative guide (in the CD), to start the network placement

and telephony plan for your enterprise. (Or you may download the latest document

from the following path: http://www.innomedia.com/support_manuals.shtml)

Wall-Mounting Instructions

Optionally, you may choose to mount your iPBX-400 on the wall.

1. Use the provided template to drill two holes on the wall.

2. Use a screwdriver to install one #6 metal screw in each hole. Leave the screw heads

1/4 to 3/8 inch away from the wall.

3. Position the iPBX with the ports at the top.

4. Place the unit above the screws and lower it so the screw heads are inside and at the

tops of the wall mount slots on the back of the unit.

5. Adjust to t. If the unit is too loose, remove it from the wall, slightly tighten screws,

and rehang.

Troubleshooting

Problem:

Telephone has no dial tone

Solution:

1. Ensure that all cables (power, Ethernet, telephone) are properly connected to the

iPBX. Ensure that iPBX’s AC power adapter is plugged in, and “PWR” indicator lights are

ON (see Front Cover Picture).

2. Pick up telephone handset (phone o-hook), check for corresponding Phone (1-4)

indicator light to be ON. Also, the “WAN”indicator light is Blinking Amber. If not, please

disconnect iPBX power cable, and then reconnect it again (see Front Cover Picture).

3. If previous steps fail, report the failure to service provider for attention.

Problem:

Cannot establish Internet connection.

Solution:

1. If the PWR, WAN, and LAN LEDs are lit, the iPBX is working properly. Try restarting

the computer so that it could reestablish a connection with the cable modem.

2. Power cycle the iPBX by switching the power to the O position, remove the power

adapter from the electrical outlet and plug it back in. Wait several minutes for the iPBX

to reestablish communications with your cable service provider.

3. If your PC is connected to a hub or gateway, try connecting the PC directly into the

iPBX.

4. Your Ethernet cable may be damaged. Try using another cable.

5. If none of these suggestions work, contact your cable service provider for further

assistance.

Appendix A. LED Status Summary

LED / Control Blinking State iPBX-400 State

PWR Steady Green Device power is on

O Device power is o

UPS Solid Orange Battery Fully Charged

Blinking Orange Battery is charging (AC power on)

Solid Green Battery is in use (AC power o)

Blinking Red Battery Low (AC power o)

Solid Red Failed or Bad battery (AC power o)

O Battery discharged (AC power o)

BATT-INT Solid Orange Battery Fully Charged

Blinking Orange Battery is charging (AC power on)

Solid Green Battery is in use (AC power o)

Blinking Red Battery Low (AC power o)

Solid Red Failed or Bad battery (AC power o)

O Battery discharged (AC power o)

WAN Blinking Amber When Data is passed through WAN Ethernet port

O No connection to Ethernet port

LAN 1-4 Blinking Amber When Data is passed while PC is connected to LAN Ether-

net port

O No PC connected to USB or LAN Ethernet ports

PHONE 1-4 Blinking Amber The connected telephone handset is on the hook (not in

use) and there are new voice mail messages

Steady Amber The connected telephone handset is o the hook

O The connected telephone handset is on the hook (not in

use) and there are no new voice mail messages

Specications

Telephone Interface 4 FXS voice ports

Connector RJ-11 REN=5

Signaling Loop start

Network Interface - Uplink Connector RJ-45

Network Interface - Downlink 10/100 Base-T

Connector RJ-45

Dimension 2.5 in (H) x 7.8 in (W) x 6.0 in (D)

63.5 mm (H) x 198 mm (W) x 152 mm (D)

Power Supply AC 100~240V/50~60Hz (DC 12V @ 4.0 Amps)

On Battery Li-ion battery providing 4 hrs Talk Time / 6 hrs Standby Time

Operating Temperature 32°F to 104°F (0°C to 40°C)

Federal Communication Commission Interference State-

ment

This equipment has been tested and found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and

on, the user is encouraged to try to correct the interference by one of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

FCC Caution: Any changes or modications not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate this equipment.

IEEE 802.11b or 802.11g operation of this product in the U.S.A. is rmware-limited to

channels 1 through 11.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncon-

trolled environment. This equipment should be installed and operated with minimum

distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

product names may be trademarks of their respective companies.

v1.2 1/10

Table des matières

Manuels PBX populaires d'autres marques

Allo.com

Allo.com Nano 2 Manuel utilisateur

ZYCOD

ZYCOD ZX50 Manuel utilisateur

Panasonic

Panasonic KX-TDA100BX Manuel utilisateur

LV switch

LV switch IPPBX800 Manuel d'instructions

Edge-Core

Edge-Core VST3305 Manuel utilisateur

Panasonic

Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Manuel utilisateur

Rauland-Borg

Rauland-Borg Telecenter IV Manuel utilisateur

Grandstream Networks

Grandstream Networks UCM6208 Manuel utilisateur

ATCOM

ATCOM IPPBX IP02 Manuel utilisateur

Panasonic

Panasonic KX-TVS50 - 2 Port Voicemail System Manuel utilisateur

bintec elmeg

bintec elmeg elmeg hybird 600 Manuel utilisateur

Panasonic

Panasonic KX-NS300 Manuel utilisateur

MCK

MCK EXTender PBXgateway Manuel utilisateur

Panasonic

Panasonic KX-NS300CN Manuel du propriétaire

NEC

NEC SL1000 Manuel utilisateur

Epygi

Epygi Quadro Quadro 2xi Manuel utilisateur

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Manuel utilisateur

AGFEO

AGFEO AC 14 analog Manuel utilisateur

InnoMedia iPBX-400 Manuel utilisateur

Manuels PBX populaires d'autres marques