Inlite SMART HUB-300 Manuel utilisateur
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
INSTALLATION MANUAL
SMART HUB-300
21 V
Attention
This product may only be used within the in-lite system. If components are used
in the system that do not originate from in-lite, the warranty no longer applies.
Install the in-lite system components (fixtures, transformers, mini-connectors,
Easy-Locks and cable connectors) so that they can easily be replaced
Never use the in-lite low-voltage cable directly connected to 100-230V. This
cable is only meant for use with the components of the in-lite 21 Volt (low-
voltage) system.
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
Contents
1x SMART HUB-300
INPUT : 230 V~, 50 Hz
Frequency: 2400-2480 MHz
POWER OUTPUT HUB-300: 21 V~, 14.3 A max., 300 VA, max. 20 dBm
Or,
1x SMART HUB-300
INPUT : 120 V~, 60 Hz
Frequency: 2400-2480 MHz
POWER OUTPUT HUB-300: 21 V~, 14.3 A max., 150 VA, max. 20 dBm
(Dimensions 228 x 143 x 82 mm / 9.0 x 5.6 x 3.2 inches.)
2x screws
Please read the following instructions before installing. You are advised
to keep these installation instructions in a safe place. Although a 21 V
system is safe, we advise you to have a qualified electrician check the
installation.
Use
The SMART HUB-300 transformer is controlled by the in-lite app, suitable for
Android and iOS phones or tablets produced, for example, by Samsung and
Apple. The transformer is fitted with an integrated timer and an astronomical
clock. You can make use of various options whereby the lamps are activated
during the hours of darkness or for a certain time period you can set yourself.
You can also manually switch the lamps ON and OFF at any time.
Bluetooth Low Energy
The transformer connects to the phone or tablet using Bluetooth Low Energy.
BLE is a new low-energy form of Bluetooth and is more user-friendly and more
secure than, for instance Wi-Fi.
Three power lines
A total of 300 VA in fixtures can be connected to the SMART HUB-300. Three
power cables can easily be connected to the transformer using the Easy-Connect
click connectors. With one transformer you’re able to create three lighting zones
in your outdoor space. It’s not necessary to evenly divide the maxiumum of 300
VA among the three lines. It’s also possible to use only 1 or 2 of the 3 power
lines.
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
Safety
The external flexible cord of this product cannot be replaced; if the cord is
damaged, the product shall be scrapped.
When the transformer is connected in a wrong way (short circuit) or it
encounters an overload, the “Off-led” will blink to signal the installer. Above a
certain level of overload the transformer will shut down and reset itself. This
procedure will loop until the connection has be done right or the load is reduced
to an acceptable level.
This product has triple protection. The protection of the G4 transformer is based
on 3 mechanisms:
1. Software based protection by switching-off output FET’s,
2. Hardware based current limiting with foldback (inside Meanwell supply).
3. Monitoring of PCB temperature.
The software protection is based on measurements of the 21V supply voltage,
the supply input current and PCB temperature.
Output current detection levels for each product are calibrated at 100% of
nominal load (14.3A @ (300VA).
If the external load is increased the following levels are reached:
•If the average current exceeds 14.3A (> 300VA) for a few seconds, the
“Button-Led” starts blinking slowly.
•If the average current exceeds 15A (> 315VA) the software protection will
switch-off the output FETs, the “Button-Led” starts blinking fast.
•The maximum load per output is 100VA. During switching of an output the
inrush current will be limited by the Meanwell supply: this supply will limit
the total current to 17.5A by switching from CV-mode to CC-mode. If this
takes longer then 400mSec. the software protection will switch-off the
output FETs, the “Button-Led” starts blinking fast until the on/off button is
activated (reset after overload).
•If the PCB temperature becomes too high the output voltage will be
switched off.
If the supply voltage for the control part becomes too low (long power dips) the
output will be disabled. After restoring of the mains supply the product will start
again in the last known mode.
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
EU Declaration of Conformity
"Hereby in-lite Design B.V. declares that the radio equipment SMART HUB-300 is
in compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available via in-lite Customer Service.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may
cause undesired operation of the device
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority
to operate this equipment. (Example - use only shielded interface cables when
connecting to computer or peripheral devices).
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
Installation
The SMART HUB-300 is easy to install. After mounting the transformer and
downloading and installing the in-lite application (app), the system is ready for
connection.
All lights can be controlled with the in-lite app on a smart phone or tablet. The
app, which is suitable for an Android and iOS device, can be downloaded from
the app store and installed on your device.
The in-lite app makes it possible to communicate with the transformer by a
Bluetooth connection. The app automatically recognizes which lines are in use. In
the app you can turn light sections (total 3) “ON” and “OFF”. You can also set
different scenarios based on sunset and sunrise, time of the day and/or
movement detection (with accessory SMART MOVE).
It’s possible to share the in-lite app with other people like familiy members. The
Share function makes it possible to quickly link an extra device. The settings are
duplicated so there’s no need to set again for the linked device.
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
Installation step by step
Although the transformer is designed to withstand inclement weather,
you are recommended not to place it close to a sprayer system. Place
the transformer at least 50 cm above the ground and in the immediate
vicinity of a 110V/230V electric socket.
Installing the transformer (Fig. 5)
Step 1
Open the package of the transformer. Here you will find the screws for
fixing the transformer in place and the terminal lugs for the cable. Fix the
transformer to a wall, panel or post using the screws supplied (Fig. 1).
Step 2
Split about 5-10 cm of the low-voltage cable end into 2 wires. Remove about 8
mm of insulation from both wire ends (Fig. 2).
Step 3
Remove the lid from the transformer so you get access to the 3 cable terminals.
Each terminal represents a separate light section in your garden.
Step 4
Insert the copper wires into the terminal lug (Fig. 3) and fix them firmly in place
by pressing the click mechanism down (Fig. 4).
Step 5
Put the lid back in place on the transformer to cover the cable terminals.(Fig. 5).
Step 6
Put the plug of the 110V/230V power cable into the electric socket. The
transformer will be switched on automatically. The on-off button on the side of
the transformer will light up continuously. (At any time it is possible to switch the
transformer on and off by a push on the on/off button)
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
FIG. 1
FIG. 2
80
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
FIG. 3
FIG. 4
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
FIG. 5
in-lite INSTALLATION MANUAL SMART HUB-300
www.in-lite.com 07-05-2021
Installing the in-lite app
Step 1
Open the app store on your Android or iOS device (smart phone or tablet).
Search for in-lite and download the app.
Step 2
Open the app on your device. You have two options to select; you’re a new user
or you already have an account. (Fig. 6)
FIG. 6
Step 3
Follow the instructions in the app. You’ll be guided through the process of logging
in or creating your account.
While creating your account you will configure the Bluetooth connection with the
transformer, the set up of your outdoor space and the names of the light
sections. (Fig. 7-14)
If you’d like to have more support you can select the option “installation manual”
at the bottom of the screen. (Fig. 6). You’ll get more information about the most
important features of the app. (Fig. 15-16)
Table des matières
Autres manuels Inlite Transformateur
Manuels Transformateur populaires d'autres marques
Delta Electronics
Delta Electronics Current Sense Transformers TCE1906H Manuel utilisateur
Hobart
Hobart 6T28-600CL Manuel utilisateur
Shinkawa
Shinkawa LS Series Manuel utilisateur
Huawei
Huawei JUPITER-3000K-H1 Manuel utilisateur
Monacor
Monacor IMG STAGELINE LTR-102 Manuel utilisateur
Lionel
Lionel ZW Manuel utilisateur
