INKSUPPLY.COM Stylus Pro 7600 Photographic Dye Ink Manuel utilisateur

Epson Stylus Pro 4000, 4800, 7600, 9600

Installation Instructions for the 4000, 4800, 7600, 9600

Fill the cartridge to approximately 90% full before installing in printer. Do not fill above the

vent hole on the end of the cart.

Remove the plug from the vent hole on the end of the cartridge. Then remove fill plug on

the top of the cartridge to fill with ink. Insert either the funnel or the spout on the Goose-

Neck fill bottle, and fill cart with ink. Go slow at first and tilt cart so air is not trapped at the

other end (septum end). Don't fill above the vent hole.

Install the small white Filter Element in the vent hole where the vent plug was previously.

Replace the larger fill plug on the top of the cart.

Use a syringe and bottom fill adapter (MIS-FADP) to extract a small amount of ink from

the end of the cartridge. This will remove any air bubbles trapped at the exit.

Ready to print. Install cartridge in printer and print, as you would with an Epson cartridge.

3000, 7000, 7500 Carts -

These Funnel Fill carts are also clear, but they do not have chips on them. Remove the

orange fill plug on the top of the cartridge to fill with ink. Insert either the funnel or the

spout on the Goose-Neck fill bottle, and fill cart with ink. Go slow at first and tilt cart so air

is not trapped at the other end (septum end). Don't fil

l above the vent hole. The vent hole is

on the end of the cart near the orange plug. Do not cover or block this small vent hole.

There is no mechanical tab to signal the printer that the cartridge is empty. So the printer

will not stop printing, but the monitoring system will warn you it is empty. DO NOT LET

THE CARTRIDGE RUN OUT OF INK.

Disabling the Epson Ink Monitoring System on 4000, 7600, 9600

The following procedures will let you disable or enable the ink monitoring system on the

printer. With the monitoring system disabled, you will be able to print continuously, but you

MUST NOT LET THE CARTRIDGE RUN EMPTY.

*Warning*

The following procedure will disable and enable the ink level indicator on Epson

4000/7600/9600 Wide Format printers. Disabling the ink level indicator will prevent the

printer from being able to recognize an empty cartridge condition. This could result in air

being drawn into the lines and possible damage to the print head. If the ink level indicator is

disabled the user must manually monitor the level of ink in the cartridges to prevent printer

damage.

The alternate to using this procedure is to use an MIS SK188 Chip Resetter. However, this

requires removing the cartridge from the printer and re-installing. This repeated "in and out"

can limit the life of the cartridge.

7600 & 9600 Ink Level Indicator Disable or Enable Procedure

1. Press the "<", "V", "enter" and "power switch" key on the panel together, then

power on. The LCD will display "VIEW CONFWTERS".

2. Press the "V" key twice. The LCD will display "SERVICE CONFIG".

3. Press the ">" key, the LCD will display "XXD".

4. Press the "V" key five times. The LCD will display "EDMODE".

5. Press the ">" key to find "*/O" in the LCD, then press the "enter" key. The count

function of ink level will be disabled. Or press the ">" key to find "*/X" in the

LCD, then press the "enter" key. The count function of ink level will be enabled.

6. Turn the printer off and on.

Note:

If the above procedure does not work, try the following.

1. Press the "<", "V", "enter" and "power switch" key on the panel together, then

power on. The LCD will display "VIEW COUNTERS".

2. Press the "V" button until the "Service Config" option appears.

3. Press the "<" once and then "V" to "EDMODE".

4. Press the "V" button to find "O" in the LCD, then press the "enter" key. The count

function of ink level will be disabled. To reverse the procedure choose "N" instead

of "O". The count function of ink level will be enabled.

5. Turn the printer off and on.

7600 & 9600 Print Head Cleaning Procedure

1. Press the "^", "V", "enter", and "power switch" key on the panel together, then

power on. The LCD will display "Cleaning".

2. Press the "V" twice to find "kk1,kk2".

3. Press the "enter" key to clean the print-head after the "kk2" display.

4. Power off and on after cleaning cycle is finished.

4000 Ink Level Indicator Disable or Enable Procedure

1. Press the "<", "^", "V", and "power switch" key on the panel together, then power

on. The LCD will display "SELF TESTING".

2. Press the "V" key. The LCD will display "SERVICE CONFIG".

3. Press the ">/enter;" key, the LCD will display "CHG DEVICE-ID".

4. Press the "V" key twice. The LCD will display "EDMODE".

5. Press the ">/enter" key, press "^" or "V" to find "*/O" in the LCD, then press the

"enter" key. The count function of ink level will be disabled. Or press the ">" key,

press "^" or "V" to find "*/X" in the LCD, then press the "enter" key. The count

function of ink level will be enabled.

6. Power off and on.

4000 Print Head Cleaning Procedure

1. Press the "<", "^", "V", and "power switch" key on the panel together, then power

on. The LCD will display "SELFTESTING".

2. Press the ">" and "enter" key, the LCD will display "Test".

3. Press the "V" key twice the LCD will display "cleaning".

4. Press the ">" key and "enter" key, the LCD will display "std kk0".

5. Press the "V" key twice, the LCD will display "std kk2".

6. Press the ">" key and "enter" key, the LCD will display "cleaning".

7. Power off and on again after cleaning is finished.

4800 Ink Level Indicator Reset - Or Resetting the Cartridge Chip

The 4800 Funnel Fill Carts have auto reset chips on them if the letters “ARC” appear on

the cartridge label. When the printer senses that the ink level is low, there will be a

flashing light on the console. This means that the level indicator is getting low. If it is

totally out of ink, the light will be on steady. These indicator lights may or may not

correspond with the amount of visible ink in the cartridge. It depends if you top them off

or not.

When the low ink light flashes, remove the cartridge by pulling back on it, far enough so

the printer can no longer contact the chip on the front of the cartridge. Wait a few

seconds, then re-insert the cartridge. This will reset the chip back to full. The flashing

light should go out.

If the 4800 Funnel Fill Carts DO NOT have auto reset chips on them if the letters

“ARC” DO NOT appear on the cartridge label. This indicates that a Standard and not an

Auto Reset chip is installed. When the printer signals that the cartridge is low on ink, use

the MIS SK188 chip resetter to reset the chip. The wide format chip resetter can be

found on this page on our website… http://www.inksupply.com/sk188.cfm

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels INKSUPPLY.COM Accessoires pour imprimantes

INKSUPPLY.COM

INKSUPPLY.COM Canon iP4000 CFS Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel