Inepro 276001 Manuel utilisateur
© 2014 Inepro B.V. All rights reserved
Technical Manual | USB Card Reader (Desktop & MFP)
USB Card Reader
(Desktop & MFP)
Product Version: Mk. II
Version of this manual: 3.0.3
USB Card Reader (Desktop & MFP)
Congratulations on your selection of Inepro card readers. We are certain you will be
pleased with your purchase of one of the flexibele solutions of the market.
We want to help you get the best result from your Inepro Back Office Suite. This manual
contains information on how to do that; please read it carefully. Due to continuous
product improvements this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its coverage
and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile card reader solution
All rights reserved. No parts of this work may be reproduced in any form or by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claim to these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting from the
use of information contained in this document or from the use of programs and source code that
may accompany it. In no event shall the publisher and the author be liable for any loss of profit
or any other commercial damage caused or alleged to have been caused directly or indirectly by
this document.
Version 3.0.3 created: October 2014 in Nieuw-Vennep.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Blom
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
R. de Koker
USB Card Reader (Desktop & MFP)
Table of Contents
Introduction 2
Inepro USB Reader Component List 4
Operation 8
Inepro Card Reader Tools 10
......................................................................................... 12Change the Configuration of the reader
......................................................................................... 15Inepro Reader Software
......................................................................................... 19Default card Read out
......................................................................................... 21Concept Summery
Software Test 23
Hardware Test 27
Appendix I 29
Notes 31
ATTENTION!!
Read this manual carefully before installing the IP Reader!
Mains connection
Guarentee
Security
Before connecting the appliance to the mains, check that the mains supply voltage corresponds
to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult
your supplier.
No guarantee can be given if safety regulations are not followed.
Always disconnect the power supply before handling anything inside the device.
This device is in conformity with the EMC directive and low-voltage directive.
CE Conformité Europeène (Conform European Norm)
End of life directives
Inepro is paying a lot of attention to environmentally-friendly production. Your new device contain
materials which can be recycled and reused. At the end of its life specialised companies can
dismantle the discarded device to recycle the reusable materials and to minimise the amount of
materials to be disposed of. Please observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This device may only be used indoors.
Indoor User Only
Directives
Version 3.0.3 - I
I
Introduction
Part
Introduction
Version 3.0.3 - 2
Introduction
The Inepro USB (Universal Serial Bus) card reader consists of a
USB interface controller board with a proximity card reader. The
controller board is programmed with software to read out the UID
(Unique ID) of the proximity card. By default the card reader reads
out the CSN (Card Serial Number) of the proximity card.
Please note that the firmware version programmed in the controller
board is depending on the proximity card technology and, if
needed, customized read out of the UID of the user card.
When a user card is presented to the reader the host device
receives the data as a keyboard input in hex format.
The Inepro USB Card Reader has an unique vendor and a
application ID. The vendor ID of Inepro = 0x1DA6, the application
ID = 0x0110. For each Inepro USB Card Reader the same
vendor/application ID is used (regardless of the used Inepro USB
card reader). At the connection procedure the software version of
the Inepro USB Card Reader is send to the host device.
Supported Proximity Card Technologies
USB Communication
The Inepro USB card readers supports the USB 2.0 protocol as a
Human Interface Device (HID)
II
Inepro USB Reader Component List
Part
Inepro USB Reader Component List
Version 3.0.3 - 4
Inepro USB Card Reader Component List
The Inepro USB card reader comes in four version, the desktop
and the MFP version in the colours grey and red. The MFP version
is meant to be mounted on the side of an MFP machine, the
desktop version for use on a flat service or installment inside the
MFP.
Inepro Desktop USB Card Reader (Grey) Kit Content 276001
(or Red 276003)
The Inepro Desktop USB Card Reader Kit consist of the following
items:
5 - USB Card Reader (Desktop & MFP)
1. Desktop USB Card Reader Kit
§1x Multi ISO Reader Desktop (Grey 276001, Red 276003)
§2x Double-sided adhesive tape (for attachment of the USB
controller to the MFD (Multi Functional Device))
§1x Manual Leaflet (P551211)
§1x Serial Stickers (P551360)
§2x Cable Duct (PS8650)
Inepro MFP USB Card Reader (Grey) Kit Content 276000
(or Red 276002)
The Inepro MFP USB Card Reader Kit consist of the following
items:
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Inepro Lecteur de cartes
Inepro
Inepro Reader Bracket for MFP Manuel utilisateur
Inepro
Inepro MagStripe - PayCon II Manuel utilisateur
Inepro
Inepro V2 Manuel utilisateur
Inepro
Inepro IP Card Reader Manuel utilisateur
Inepro
Inepro PayCon II Manuel utilisateur
Inepro
Inepro Spider RFID Reader Manuel utilisateur
Inepro
Inepro Spider Desktop Manuel utilisateur
Inepro
Inepro Biometric Fingerprint Manuel utilisateur
Inepro
Inepro Spider Desktop Manuel utilisateur
Inepro
Inepro SCR808 Manuel utilisateur
