Gas supply
Connection to the gas supply with a exible pipe
RISK OF FIRE
WARNING
Always use tubing and pressure regulators according to
local regulations.
The appliance must be disconnected from the gas supply
piping system during any pressure testing of that system.
Check the validity of hoses and pressure regulators and
replace them if it is necessary.
Properly tighten all gas connections during installation.
Install the stove according to specifications described.
Failure to follow these instructions can cause explosion, fire
or damage to people’ s physical integrity.
INSTALLER MANUAL
Installation and setup
Instructions Manual
PAG 6
If your stoye does not have gas outlet:
Ask an Authorized Technical Service
to provide the respective connector or
gas outlet according to the
distribution pipe thread (thread
3/8” BSPT or 1/2” ISO 228 ).
If your stove has gas outlet: The connection of
the flexible hose depends on the gas inlet tube
and distribution tube andi t must be executed
by qualified personnel.
Note: Some stoves have accesories included
within the gas inlet, the connection must be
done by qualified personnel.
ab
IMPORTANT:
•The gas supply must be placed on the same side of the crimp connector (gas outlet) of
your stove.
•The gas supply must be made with a flexible suitable gas hose of 8 mm (5/16’’) or 13 mm
(1/2’’) internal diameter (depending on the gas supply of your stove) and 1.5 to 2 meters
length, which carry out the requirements of flexibility, duration and minumun thermal
resistance of 70ºC (158ºF) (Reference for Colombia: NTC 3561. Reference for Ecuador: NTE
INEN 885 ), 60ºC (140ºF) ( Reference for Peru: NTP 300.065.)
•Some countries do not allow the connection to a flexible hose. See respective technical
provisions.
•The use of oven generates hot gas evacuation and heats backwards surface which can
damage the hose causing serious risks.
•Depending of use conditions of your stove, some zones eventually may reach a
temperature of 135ºC (275ºF.) Use a proper connector tube according to the
corresponding national installation requirements in force.
•Be sure service cord contacts the back of the stove (hot oven.)
•Be sure supply hose does not cross or contact the
back of the stove, if this is unavoidable, install flanges
which are included in the accessories of some models
of stoves or use another device for accomplishing the
same function. Check the chart for a correcto
installation of flanges, which are the guiding for the
hose, the use of oven generates hot gas discharge that
can damage the hose causing serious risks.
General diagram of parts and components.
INSTALLER MANUAL
Installation and setup
PAG 5
Instructions Manual
1.-Lateral generator support
2.-115 - 220 V transformer
3.- Fixing screw valves and thermostat
4.- Flange valves setting and
thermostat
5.- Thermostat / Oven valve
6.- Burner valve panel
7.- Tub ramp distribution
8.- Floor burner
9.- Floor burner stew
10.- Floor burner thermocouple
11.- Floor burner injector
12.- Floor burner portaciclor
13.- Floor burner pipe
14.- Gas supply
15.-Mixer pipe panel
16.- Fixation stew clasp
17.- Board stew
18.- Grill burner inyector
19.- Grill burner portaciclor
20.- Grill burner pipe
21.- Grill burner stew
22.- Griil buerner thermocouple
23.- Grill burner
24.- Burning board caps
25.- Burning board panel
26.- Mixer board cup
27.- Stove harness
1
17
18
19
20
23
22
24
25
21
16
15
14
13
2
11
9
10
3
4
5
6
8
12
7
26
27
Left position
Quartz line
Other lines central position
•Remove all accessories that packaged in the oven.
•Check the “ General diagram of parts and components” to know the names of
the components of the device and its location.
•Check burner sizes and select appropriate sizes of bases and end caps.
•Place the burner bases, end caps and grills so that they are firmly seated,
without balancing and whit proper coupling between the parties, as the items
listed below:
- Make sure the burner base is correctly placed, centered, fixed and the
corresponding burner.
- If your stove has triple crown burner check that yht inner end cap is the same
size of the central ring.
- Check that the end caps are centered and fully seated in the burner, without
leaving raised on one side.
If the placement of the accessories listed is incorrect, there is a risk of accidents or damage to the appliance.
IMPORTANT:
- Check the correct settlement moving the end caps slightly from side to side on the burner base until
you hear the lock in a fixed position.
- Check the assembly of components, nothing that when you turn the burner flames are blue, well
defined and no strange noises.
INSTALLATION INSTRUCTIONS FOR COVER ACCESSORIES.
