Incra Miter Express Manuel utilisateur

Owner’s Manual

■ Before using the INCRA Miter Express, read and

follow all of the instructions and safety information in

this owner’s manual.

■ When using the INCRA Miter Express in conjunction

with any other tool, rst read and follow all instructions

and safety information in that tool’s owner’s manual.

■ Never let the saw blade come in contact with the

aluminum or steel components of the INCRA Miter

Express.

■ Before making any cut, always make sure that the

INCRA Miter Express cutoff drop panel is locked

securely in the miter slot.

■ When using the INCRA Miter Express, always keep

your hands clear of the saw blade and the line of cut.

■ Always turn off the power and make sure that the saw

blade comes to a complete stop before changing the

setting of any part of the INCRA Miter Express.

■ Always securely tighten your miter gauge’s clamping

knob before starting any cut.

■ Wear safety glasses, hearing protection, and follow all

normal shop safety practices.

■ After making any adjustments to the miter angle or

fence position of your miter gauge, always verify safe

clearance between the blade and fence before turning

on the saw.

■ After making any adjustments to the fence position on

the INCRA Miter Express, always make sure that all

knobs and fasteners on the fence mounting bracket

and the outboard fence lock are securely tightened.

■ When using a stop to position a piece for a cut, always

hold or otherwise clamp the board between the stop

and the blade.

■ Always make sure the arrows on the Miter Express

caution label point toward the table saw blade.

Important safety instructions for using the INCRA Miter Express

saFeTY

Upgrades your miter gauge to a sled for increased accuracy,

control and safety on work pieces large and small.

Another innovation in precision from INCRA®

Miter gauge not included.

Miter gauge not included

FIG. 1 Miter Express Components

ASmall Miter Express Panel w/rounded corners

BSmall Miter Express Panel w/square corners

CLarge Miter Express Panel

DHold Down Clamp

EHardware Pack C-15 (Outboard Fence Support and

Fasteners)

FHardware Pack C-13 (Panel Assembly Fasteners and

Hex Keys)

GHardware Pack C-14 (T-Slot Retainers and Cam

Screws)

HUtility Plate

I Panel Connector

JAluminum Miter Bar

KUHMW Glide Strips

Miter Express Owner’s Manual (not pictured)

ParTs lIsT

Carefully Unpack Components

After carefully unpacking all components, check the contents against the photo in Fig. 1 and parts list below.

asseMBlY

FIG. 2 Left of blade

FIG. 3 Right of blade

Left or Right Miter Slot

Before beginning the panel assembly, you’ll want to rst determine on which side of the blade you want the miter

sled. Typically, if your blade tilts to the right, you’ll want the miter sled to the left of the blade (Left Miter Slot), Fig. 2.

If your blade tilts left, then you’ll want the sled on the right side of the blade (Right Miter Slot), Fig. 3.

Attach Panels to Utility Plate and Panel Connector

Place the Utility Plate in the miter slot selected for use. Orient the Utility Plate so that the small T-slot on the

plate is between the miter slot and your blade. The arrows on the Utility Plate Caution label MUST point toward

the blade. Open Hardware Pack C-13 and using the supplied #10-24 x 15/32” Phillips at head screws, attach the panels

to the Utility Plate and Panel Connector as shown in Figs. 4A and 4B. The large panel will mount to the Utility Plate

using the holes closest to the blade. The small panel with square corners mounts to the opposite edge of the Utility Plate.

Use the Panel Connector to join the small panel with rounded corners to the remaining edge of the small panel with

square corners.

FIG. 6 Cut oﬀ drop panel

FIG. 5 Adjust utility plate for smooth glide

Adjust Utility Plate for Smooth Glide in

Your Miter Slot

Using the included 3

32” hex key, adjust the (4) expansion

mechanisms in the Utility Plate for a good sliding t in your

table saw’s miter slot, Fig. 5. Turning the screw clockwise

expands the mechanism. Expand a little at each of the

locations until the Utility Plate slides smoothly with no side

play.

NOTE: To relax the expansion mechanism, turn the

screw counter-clockwise as you push down on the

hex key.

Raise Saw Blade and Cut Drop Panel

BLADE ANGLE NOTE: If your primary use for the

Miter Express is mitering with the blade at 90º, make

sure the blade is set at 90º before continuing.

Raise your saw blade about ¾” and make a cut to remove

the portion of the large panel that extends across the line

of cut, Fig. 6. This cut off will be used for the drop panel

described in Step 6. Turn off the saw, lower the blade and

remove the Utility Plate assembly from the saw.

FIG. 4A Panel assembly left of blade

FIG. 4B Panel assembly right of blade

NOTE: All illustrations following Fig. 4B

will show only assembly illustrations for

left side of blade on right tilt table saws.

#10-24 x 15/32”

Phillipsﬂat head

screws

Small panel

with rounded

corners

Small panel

with square

corners

Largepanel

Panel connector Utility

plate SmallT-slot

Utility plate

Adjust all (4)

expansion mechanisms

3/32” Hex key

Utility plate

assembly Drop panel

FIG. 10 Attach T‑slot retainers

FIG. 8 Attach drop panel to miter bar

FIG. 9 Cut oﬀ drop panel overhang

Attach Drop Panel to Aluminum Miter Bar

Using (4) #10-24 x ¾” Phillips at head screws,

attach the drop panel to the aluminum miter bar. Use

the mounting holes that permit the least amount of panel

overhang beyond the line of cut, Fig. 8.

Cut Off Drop Panel Overhang

Raise the saw blade about ¾” and make a cut to

remove the portion of the drop panel that extends beyond

the line of cut, Fig. 9. Turn off the saw, lower the blade

and return the Utility Plate assembly to the table saw.

CAUTION: In use, only the Utility Plate assembly

slides to move your workpiece through a cut. The

drop panel will be positioned adjacent to the blade

and locked in place by tightening the (2) expansion

mechanisms to provide zero clearance and workpiece

cutoff support. (See Fig. 12)

Attach T-Slot Retainers

Note: Skip this step for non T-slot miter channels.

Open Hardware Pack C-14. Slide the Utility Plate panel

assembly to overhang the edge of your table saw and

attach the T-slot retainer using the #10-32 x 3

8” Phillips

pan head screw as shown in Fig. 10.

The raised rim around the T-slot retainer’s threaded hole

should face upward. Repeat for the opposite end of the

Utility Plate.

FIG. 7 Adjust aluminum miter bar

Adjust Aluminum Miter Bar

Using the supplied 3

32” hex key, adjust the aluminum

miter bar at each of the (2) expansion mechanism

locations for a good sliding t in your table saw’s remaining

miter slot. Turning the screw clockwise expands the

mechanism. Expand a little at each of the locations until

the bar slides smoothly with no side play, Fig. 7.

Expansion

mechanisms

3/32” Hex key

Aluminummiter bar

Drop panel

#10-24 x ¾”

Phillipsﬂat head

screws

Miter bar

Droppaneloverhang

Drop panel

#10-32x ³/₈”Phillips panhead screw

Utility plate

T-Slot retainer

Raised rim face up

FIG. 11 Apply UHMW glide strips

Apply UHMW Glide Strips

Apply one strip of PSA backed UHMW to the

underside of each of the (3) panels that make up the Utility

Plate panel assembly, Fig. 11.

Align the UHMW so that it contacts only smooth surfaces

on your table saw. The UHMW strips serve to raise the

Miter Express panels just slightly above the drop panel

while simultaneously lowering friction between your table

saw and the panels.

NOTE: Do not apply UHMW glide strips to the

underside of the drop panel.

OPeraTIOn

FIG. 13 Position miter gauge in receiving slot

FIG. 14B Gauge position for maximum crosscut

FIG. 14A Gauge position for small piece work

FIG. 12 Position and lock drop panel

Position and Lock Drop Panel

Slide the drop panel assembly in your miter slot and

position adjacent to the saw blade. The infeed edge of

the drop panel should be about 2-3” in front of the saw

blade. Use the 3

32” hex key to tighten both expansion

mechanisms to lock the drop panel in place, Fig. 12.

Position Miter Gauge in Receiving Slot of

Utility Plate

Slide the Utility Plate assembly into the remaining miter

slot and lower your miter gauge into the receiving slot of

the Utility Plate, Fig. 13.

Once in the receiving slot, a variety of positions for the

miter gauge can be achieved to accommodate different

cutting situations. For small piece work you’ll want the

miter gauge positioned forward on the Utility Plate so that

the work piece will be fully supported by the Miter Express

panels. For maximum crosscut you’ll want to position the

miter gauge fence mounting plate near the infeed end of

the Utility Plate. Figs. 14A and 14B.

UHMWstrip

Drop panel assembly

3/32” Hex key

Tighten expansion

mechanisms to

lock drop panel in

place

2 - 3”

Utility plate

Receivingslot

Make Your Cut

Now use your new Miter Express as you would any

miter gauge. Just set your miter angle, check for safe

clearance between your miter gauge’s fence and the blade

and make the cut, Fig. 16.

Be sure to read the accessories section of this manual

for information on the included Outboard Fence

Support and INCRA Hold Down Clamp.

4FIG. 16 Make your cut

FIG. 15A Lock miter gauge in place securely

Lock the Miter Gauge in Place

CAUTION: All THREE of the supplied cam screws

(Hardware Pack C-14) must be positioned and FIRMLY

TIGHTENED against the side of your miter gauge’s

miter bar. CONFIRM that your miter gauge is securely

locked in the Miter Express before making any cuts.

After determining your miter gauge’s position on the Miter

Express (Step 2, Fig. 14A & 14B), remove the gauge from

the receiving slot and install one of the three cam screws

in the threaded cutout that will be closest to the miter

gauge’s protractor head (either in front or behind is OK as

long as it will bear against the miter bar). Install the other

two cam screws so they will be adjacent to any other two

points along the miter bar, Fig. 15A

Use the supplied 1/8” hex key to tighten each cam screw as

far down as it will go, THEN back it out one full turn. Now

rotate each cam screw clockwise until there is enough

head clearance for the miter bar to drop all the way into

the receiving slot. Continue tightening each cam screw

until it is FIRMLY tightened against the miter bar.

NOTE: When properly installed, each cam screw will

be roughly centered on the 3/8” thickness of the miter

bar. This means the cam screws should bear against

the middle of the miter bar, NOT the very top and NOT

the very bottom, Fig. 15B.

Tighten cam screws

aCCessOrIes

Outboard Fence Support

For heavy duty applications, use the included outboard

fence support to provide a rock solid backing for the end

of your miter gauge’s fence. To use the support, open

Hardware Pack C-15. Loosely install one of the ¼-20 x ¾”

hex bolts with washer and ¼-20 knob through the hole in

the outboard fence support, then slide the head of the bolt

into the T-slot on the panel connector, Fig. 17.

FIG. 17 Outboard fence support

Outboardfence

support

¼-20

Clampingknob

¼” Washer

¼-20 x ¾” Hex bolt

Panelconnector

1/8”Hex key

FIG. 15B Cam screw placement- Cutaway View

Cam screw Miter bar

FIG. 18 Use with INCRA Miter Gauge fences

FIG. 21 Panel connector shifted forward

FIG. 22 Panel shifted to permit clamping wide crosscut

For use with other non-INCRA miter gauge fences, after

setting the protractor head angle and tightening the large

clamping knob, slide the support up to contact the back

of the fence and tighten the clamping knob to secure the

support to the panel connector, Fig. 19

FIG. 19 Use with non-INCRA miter gauge fences

FIG. 20 Panel connector shifted backward

To use the outboard fence support for angle settings that

pivot the fence off of the Miter Express base, you can

shift the position of the panel connector. Just remove

the fasteners and shift the panel connector backward or

forward a few holes, Figs. 20 and 21.

A forward shift is benecial when using the included hold

down clamp for wide material crosscuts, Fig 22.

For use with most INCRA Miter Gauge fences, you can

use the remaining hex bolts with washers and knobs to

attach the fence to both the outboard fence support and to

the Miter Gauge’s fence mounting bracket, Fig. 18. (You

can continue to use the socket head fasteners provided

with your INCRA Miter Gauge if you prefer.)

In operation, after setting the protractor head angle and

tightening the large clamping knob, you must tighten the

outboard support to the fence before tightening to the

panel connector. After making a cut, be sure to loosen

both clamping knobs before changing miter angles. Try

setting a few angles to get the hang of it.

¼-20 x ¾” Hex bolts

w/washers and

clamping knobs

INCRA

miter gauge

fence

Slide support to

contact rear of fence

and tighten thumbscrew

Made in America by:

Taylor Design Group, Inc.

✦

P.O. Box 810262

✦

Dallas, Texas 75381

✦

Tel: (972) 242-9975

✦

Fax: (972) 243-4277

✦

Web Site: www.INCRA.com

Printed in the U.S.A.

✦

INCRA is a registered trademark of Taylor Design Group, Inc.

INCRA products are protected by one or more of the following U.S. Patents: #4,793,604, #4,930,221, #5,195,730 #5,275,074,

#5,423,360, #5,716,045, #6,237,457, # 6 , 5 57, 6 01, #6,672,190 Other patents granted or pending.

warranTY

Taylor Design Group, Inc. warrants this product for one year from date of purchase. We will repair any defects due

to faulty material or workmanship, or at our option, replace the product free of charge. Please return the failing

component only, postage prepaid, along with a description of the problem to the address below. This warranty

does not apply to parts which have been subjected to improper use, alteration, or abuse.

07/05

FIG. 23 Hold down clamp assembly

INCRA Hold Down Clamp

Open the INCRA Hold Down Clamp hardware bag and

assemble the clamp as shown in Fig. 23.

The INCRA Hold Down Clamp slides into either of the (2)

T-slots on the Miter Express to provide a secure grip on

your work piece, large or small. Either end of the clamp

can be used to clamp your workpiece. Just slide the

clamp into the selected T-slot and tighten the clamping

knob, Fig. 24.

FIG. 24 Hold down clamp in use

¼-20Clamping knob

¼” Washer

Clamp body

¼-20 Hex bolt

Pivot barrel

CAUTION: Never allow any part of the INCRA

Hold Down Clamp to cross the line of cut.

Made in America by:

Taylor Design Group, Inc.



P.O. Box 810262



Dallas, Texas 75381



Tel: (972) 242-9975



Fax: (972) 242-9985



Web Site: www.incra.com

WARRANTY

Taylor Design Group, Inc. warrants this product for one year from date of purchase. We will repair any defects

due to faulty material or workmanship, or at our option, replace the product free of charge. Please return the

failing component only, postage prepaid, along with a description of the problem to the address below. This

warranty does not apply to parts which have been subjected to improper use, alteration, or abuse.

You can also register your INCRA product online at www.incra.com. It’s quick and easy!

Scan this QR code to register your product online

Table des matières

Autres manuels Incra Accessoires pour outils électriques

Incra

Incra Ultra Lite Manuel utilisateur

Incra

Incra Wonder Fence Manuel utilisateur

Manuels Accessoires pour outils électriques populaires d'autres marques

Bosch

Bosch OSC004 Manuel utilisateur

Rockler

Rockler 57510 Manuel utilisateur

Bosch

Bosch RA1054 Instructions de montage

Grizzly

Grizzly T10808 Manuel utilisateur

Kitagawa

Kitagawa SC N Series Manuel utilisateur

Wolfcraft

Wolfcraft FKS 145 Guide rapide

ADAMAS

ADAMAS B32 Manuel utilisateur

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Manuel utilisateur

Echo

Echo Speed-Feed Universal 400 LH/RH Manuel utilisateur

SCHUNK

SCHUNK ROTA TB-TBS-EP Instructions d'utilisation

Schmid

Schmid RAPID Secure XL Manuel utilisateur

Drill Master

Drill Master 360X Manuel utilisateur

Toro

Toro 138-5050 Manuel utilisateur

jbc

jbc SF-SD Manuel utilisateur

Bosch

Bosch GTA 3800 Professional Instructions de montage

RG AVAK

RG AVAK MaxDrill Series Manuel utilisateur

infaco

infaco PW3 Manuel utilisateur

Gloria

Gloria CUT & BRUSH Manuel utilisateur