Inaxsys Incomlink INC-3URX-256 Guide de l'utilisateur

Installer Manual

Incomlink | INC-3URX-256

CONTENT
1. INTRODUCTION.......................................................................................................................3
2. SYSTEM STRUCTURE.............................................................................................................3
2.1 CPM card..............................................................................................................................3
2.2 LC telephone line card  optional).........................................................................................4
2.3 RC radio receiver card  optional)..........................................................................................4
2.4 PWR power supply card.......................................................................................................4
2.5 IP card  optional)...................................................................................................................4
2.6 Monitoring software compatibility.......................................................................................5
3. FIRST STEPS..............................................................................................................................5
4. INSTALLATION.........................................................................................................................6
Mounting the receiver unit..........................................................................................................6
Printer connection.......................................................................................................................6
PC connection.............................................................................................................................6
CPM central processing card backside connectors.....................................................................7
PWR power supply card backside connectors............................................................................8
LC telephone line card backside connectors  optional)..............................................................9
RC radio receiver card backside connectors  optional)............................................................10
IP Ethernet receiver card backside connectors  optional).........................................................11
Card installation and replacement.............................................................................................12
5. TECHNICAL DATA..................................................................................................................12
2

1. INTROD CTION

Thank you for choosing our product. This modern and reliable monitoring receiver not

only guarantees the highest level of security, but also it is a useful colleague in the life

of every monitoring company, because of its user-friendly handling and intelligent

functions.

To use the highest range of provided functions please read carefully the Installer

Manual.

For the confident programming and secure usage please keep all warnings in Installer

Manual, with highly focusing to security directions.

2. SYSTEM STR CT RE

INC-3URX-256 monitoring receiver provides complex and reliable solution to

build up a modern monitoring station. The device can receive signals from alarm

control panels through IP network, telephone line and radio channel. Due to the

universal operation, the device can receive all standard (and most of the non-standard)

signals from alarm control panels and communicators. With combination of an

appropriate PC-based monitoring software it guarantees not only reliable signal

transmission, but also easy to use operator interface. The system consists of the

following devices:

2.1 CPM card

Central processing card (CP ) which controls the operation of the receiver.

CP contains two serial ports (respectively 2 high speed USB ports), one Ethernet port

and one parallel printer port. CP card can store up to 2000 events in its non-

volatile memory. If the connection fails with monitoring computer, the receiver stores

events in its own memory, and all events will be sent automatically when the

connection is restored. CP controls the graphical LCD display as well, where

received events can be seen and basic settings can be done.

2.2 LC telephone line card (optional)

Receiver has 8 slots to connect LC telephone line cards. LC line cards can monitor one

telephone line. Each telephone line card have memory to store up to 500 events or

caller ID. Caller ID function is built in, the caller telephone number is stored and can be

transmitted to monitoring computer. Line cards support two-way audio communication

also. Line cards are continuously monitored by CP . All line card troubles are displayed

immediately at LCD display, and transmitted to monitoring computer. The line card

monitors the connection with CP as well, if it detects trouble automatically switches to

standalone operation mode. In this case it continues event receiving, but stores them in

its own memory. All received events will be sent automatically to CP when the

connection is restored.

2.3 RC radio receiver card (optional)

The optional RC radio receiver card works as a special line card in the system – it

provides event receiving through UHF radio (440..450 Hz). RC card can handle two

independent radio channels, which are displayed as line card “A” and “B” in the system.

Event management and CP monitoring way is similar to LC line cards. In standalone

mode the RC card can store up to 500 events, which will be sent automatically to CP

when the connection is restored.

2.4 PWR power supply card

PWR power supply card ensures voltage for all cards in the system. The input of PWR

requires 16.5 VAC / 18 VDC, which is generated by an external transformer unit / power

supply unit. PWR has got battery charging circuit, batteries can be connected to

external connectors. In case of main power trouble battery powered operation is

switched automatically. The capacity of batteries should be between 7 Ah and 15 Ah.

The PWR continuously check the state of main power and batteries, and it reports the

status to CP unit.

2.5 IP card (optional)

Receiver has 8 slots to connect IP Ethernet based receiver cards. IP cards can work in

standalone mode, they control individually the incoming events through Ethernet line.

Then they forward events to central processing unit through internal receiver bus. IP

card gives extended range in IP receiving functions (comparing to CP ). Additionally it

provides possibility to connect the system to a secondary Internet provider.

2.6 Monitoring software compatibility

The device can work with the most generally used monitoring software packages.

The device can work with the most generally used monitoring software packages:

SURGARD receiver type should be selected as receiver type.

3. FIRST STEPS

Please unpack the device carefully and please check is there any damage on

that caused by transport. If there is any obvious damage do not switch on the device,

please call the distributor. The basic package contains the following units:

•INC-3URX-256 monitoring receiver (1 CP card, 1 PWR card)

•RS232 cable for PC connection

•USB cable for PC connection

•16.5 VAC transformer and power cable / 18 VDC power supply

unit

•Battery connector cable (without battery)

•User anual

•Programming anual

•Installer anual

Before mounting the device to its operation environment, receiver test is recommended.

For this connect the external power supply to the PWR card 16.5 V AC terminals and

the battery to the „BATTERY 1 +” and „BATTERY 1 –” connectors. The receiver

executes a self-test after connecting the power supply and it detects system

components (optional LC line cards, IP cards, RC radio receiver card). After this

operation the event list can be seen on LCD display.

Note: Battery usage is only recommended at BATTERY 1 connector. In special cases

(usage without main power) it is possible to use two batteries (another battery on

BATTERY 2 connector) to provide continuous operation, but is not recommended for

long term usage.

Note: Battery charging voltage can be only measured if the battery is connected.

4. INSTALLATION

Mounting the receiver unit

INC-3URX-256 is manufactured in a 3HE height 19” table housing. In addition it

can be mounted to a standard 19” rack case by means of the holes in front board.

Note: The table stands might be folded up in case of installation to a rack case.

Note: LCD display is planned to be well seen in table usage. If the receiver is installed

over the eye-level, it is recommended to turn a bit downward for better readability.

Printer connection

Any type of parallel printer can be used with Centronics connector. Connect the cable of

the printer to the LPT port of the CP unit.

Note: In view of the default usage of the device, it is recommended to use matrix printer

as against laser / ink-jet printers for event print.

PC connection

For the connection to monitoring software connect the receiver CO A (USB A) port to

the serial port (USB port) of the monitoring PC. Use the cable provided in receiver

package. If the cable length is not enough, you can use USB expander cable or RS232

expander cable (CO A – 2, 3, 5 pin; PC [9 pin] – 3, 2, 5 pin). With this you may have

up to 10-12 m distance between receiver unit and monitoring PC.

Note: CO A and USB A ports are equivalent, as the CO B and USB B ports. Do not

connect devices at the same time to CO A and USB A ports. If it is possible, always

recommended to use CO A as against USB A.

Note: If the A serial port of the receiver has any trouble, B port can work as a

replacement. For this some small configuration steps are required which can be found

in Programming Manual.

CPM central processing card backside connectors

RESET – Hardware reset button.

CO A – Default communication port for PC connection.

CO B – Reserve communication port for PC connection (or for external receiver).

LPT – Parallel printer port.

TCP/IP – Ethernet connector for IP monitoring and for remote programming.

USB A – Default communication port for PC connection (if there is no serial port)

USB B – Reserve communication port for PC connection.

+12 V – Power connector for control functions. Up to 500 mA load capacity.

PG 1 / PG 2 – For future usage.

BUZZER – To connect external buzzer (intermittent shortcut with GND during internal

buzzer activation, if the internal buzzer is enabled). Up to 50 mA load capacity.

TA PER – Works as NO tamper switch if the tamper function is enabled.

EXT. ACK – Works as external acknowledge button (shortcut with GND means manual

acknowledge, same way as ENTER button) if external acknowledge function is enabled.

Note: Install a 10 K pull-up resistor between EXT. ACK and +12 V terminals.

GND – Common GND connector for control functions.

PWR power supply card backside connectors

For device installation connect the external voltage to the PWR card 16.5 V AC

terminals and the battery to the „BATTERY 1 +” and „BATTERY 1 –” connectors. The

receiver executes a self-test after connecting the power supply and it detects system

components (optional LC line cards, RC radio receiver card, IP card). After this

operation the event list can be seen on LCD display.

Note: Battery usage is only recommended at BATTERY 1 connector. In special cases

(usage without main power) it is possible to use two batteries (another battery on

BATTERY 2) for continuous operation, but is not recommended for long term usage.

Note: Use only the power supply (18 VDC) / transformer in receiver package (or a

replacement transformer with at least 50VA @ 16.5 VAC capacity).

BAT – 3.15 A – Fuse to protect battery circuit.

AC – 3.15 A – Fuse to protect AC power supply circuit.

BATTERY 1 – Primary battery connector (7-15 Ah).

BATTERY 2 – Secondary battery connector (7-15 Ah).

16.5 V AC – ain power supply connector (18 VDC power

supply / transformer in receiver package or at least 50 VA @

16.5 VAC capacity replacement transformer).

- GROUND – Standard 5 nut for grounding power

supply unit. It is not allowed to use the receiver without

proper grounding.

Note: To provide appropriate protection against electrostatic and electromagnetic

interferences the device housing should be grounded properly. Grounding of housing

and grounding of telephone line cards can be connected only at the common ground

point (at least 2 m distance between each card grounding point – 5 nut / terminals).

Grounding is essential for flash of lighting and over-potential protection, absence of

proper grounding may cause communication problems as well.

Note: Never connect grounding point to receiver GND terminal, it may cause damage.

LC telephone line card backside connectors (optional)

LC line card is suitable to receive analog (PSTN) telephone line. Connect the telephone

line into the “LINE/SET” RJ11 connector at the backside of the line card. In case of

ISDN line use one of the analog line outputs of ISDN NT box. For two-way audio

connection the telephone set should be connected to “LINE/SET” connector also. The

incoming telephone line should be connected to the two internal connector interfaces (3-

4), telephone set should be connected to the two external connector interfaces (2-5).

Pay attention that connected telephone set should be in line, as if it is in hanged up

state the two-way audio connection doesn't work. Check device impedance as well – it

should be 600 ohm for normal phone sets.

LINE / SET – Analog telephone line connector.

– GROUND – Terminals to connect telephone line card

(into either of connectors).

Note: Grounding of housing and grounding of telephone line cards can be

connected only at the common ground point (at least 2 m distance

between each card grounding point – 5 nut / terminals). Grounding is

essential for flash of lighting and over-potential protection, absence of

proper grounding may cause communication problems as well.

RC radio receiver card backside connectors (optional)

RC radio receiver card can handle two independent radio channels. Channel “A” is

usually supplied with built in radio (or external radio for special request). Channel “B”

only can be used with an external radio unit. If the channel “A” is supplied with built in

radio (RTX 2U2), only the antenna should be connected to “ANT” connector. Pay

attention for using UHF antenna with suitable end of line resistor (50 ohm), and the RF

cabling should have minimal loss.

Note: If you want to use channel “B” with external radio unit, please contact your

distributor.

RSP – Radio serial port for programming without

CP (radio repeater stations), and for debugging.

ANT – Antenna connector for built in radio units

(channel „A”).

Note: Always choose the appropriate antenna

according to the installation site of the receiver.

RADIO 2: External radio connector (for channel „B”).

RADIO 1: For special request channel „A” might be

supplied with external radio unit.

Table des matières

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur