Inaxsys Standalone DVR Manuel utilisateur

Standalone DVR Quick Start Guide

Version 1.0.0

Table of Contents

1Hardware Installation and Connection.......................................................................1

1.1 Check Unpacked DVR ......................................................................................1

1.2 About Front Panel and Rear Panel..................................................................1

1.3 After Remove the Chassis................................................................................1

1.4 HDD Installation.................................................................................................1

1.4.1 HDD Calculation................................................................................1

1.4.2 HDD Installation ................................................................................2

1.5 Rack Installation ................................................................................................4

1.6 Front Panel.........................................................................................................4

1.7 Rear Panel .........................................................................................................4

1.8 Connection Sample ...........................................................................................5

1.9 Alarm Input and Output Connection ................................................................6

1.9.1 Alarm Input and Output Details.........................................................7

1.9.2 Alarm Input Port ................................................................................7

1.9.3 Alarm Output Port..............................................................................8

2Overview of Navigation and Controls ........................................................................9

2.1 Boot up & Shut Down........................................................................................9

2.1.1 Boot up..............................................................................................9

2.1.2 Shut Down.........................................................................................9

2.1.3 Auto Resume after Power Failure ...................................................10

2.1.4 Replace Button Battery ...................................................................10

2.2 Change Password ........................................................................................... 10

2.3 Startup Wizard ................................................................................................. 11

2.4 Preview............................................................................................................. 13

2.5 Realtime Playback (Instant Playback)........................................................... 13

2.6 Manual Record................................................................................................. 14

2.7 Search & Playback ..........................................................................................15

2.8 Schedule...........................................................................................................16

2.9 Network............................................................................................................. 17

2.10 PTZ................................................................................................................ 18

2.10.1 PTZ Setup.......................................................................................18

2.10.2 PTZ Operation.................................................................................19

2.10.3 Coaxial Control................................................................................20

2.11 Channel Type ............................................................................................... 21

2.12 Remote Device............................................................................................. 23

3Web Operation...........................................................................................................25

3.1 Network Connection........................................................................................ 25

3.2 Login ................................................................................................................. 25

3.3 Main Window.................................................................................................... 25

3.3.1 LAN Login .......................................................................................25

3.3.2 WAN Login......................................................................................26

iii

Welcome

Thank you for purchasing our DVR!

This quick start guide will help you become familiar with our DVR in a very short time.

Before installation and operation, please read the following safeguard and warning carefully!

Important Safeguard and Warning

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The product must be grounded to reduce the risk of electric shock.

We assume no liability or responsibility for all the fires or electrical shock caused by improper

handling or installation.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Keep upwards. Handle with care.

Do not apply power to the DVR before completing installation.

Do not place objects on the DVR.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

6. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included:

Contact your local retailer ASAP if something is missing in your package.

7. Lithium battery

Improper battery use may result in fire, explosion, or personal injury!

When replace the battery, please make sure you are using the same model!

Caution

FOR YOUR DEVICE SAFETY, PLEASE CHANGE SYSTEM DEFAULT PASSWORD AFTER

YOU FIRST LOGIN IN!

1Hardware Installation and Connection

Note: All the installation and operations here should conform to your local

electric safety rules.

1.1 Check Unpacked DVR

When you receive the DVR from the forwarding agent, please check whether there is any visible

damage. The protective materials used for the package of the DVR can protect most accidental

clashes during transportation. Then you can open the box to check the accessories.

Please check the items in accordance with the list. (Remote control is optional). Finally you can

remove the protective film of the DVR.

Note

Remote control is not a standard accessory and it is not included in the accessory bag.

1.2 About Front Panel and Rear Panel

For detailed information of the function keys in the front panel and the ports in the rear panel,

please refer to the User’s Manual included in the resource CD.

The model label in the front panel is very important; please check according to your purchase

order.

The label in the rear panel is very important too. Usually we need you to represent the serial

number when we provide the service after sales.

1.3 After Remove the Chassis

Please check the data cable, power cable, COM cable and main boar cable connection is secure

or not.

1.4 HDD Installation

1.4.1 HDD Calculation

Calculate total capacity needed by each DVR according to video recording (video recording type

and video file storage time).

Step 1: According to Formula (1) to calculate storage capacity

that is the capacity of each

channel needed for each hour, unit Mbyte.

102436008  ii dq

(1)

In the formula:

means the bit rate, unit Kbit/s

Step 2: After video time requirement is confirmed, according to Formula (2) to calculate the

storage capacity

, which is storage of each channel needed unit Mbyte.

(2)

In the formula:

means the recording time for each day (hour)

means number of days for which the video shall be kept

Step 3: According to Formula (3) to calculate total capacity (accumulation)

that is needed for

all channels in the DVR during scheduled video recording.





iiT mq 1

(3)

In the formula:

means total number of channels in one DVR

Step 4: According to Formula (4) to calculate total capacity (accumulation)

that is needed for

all channels in DVR during alarm video recording (including motion detection).





iiT mq 1

×a% (4)

In the formula：a% means alarm occurrence rate

You can refer to the following sheet for the file size in one hour per channel. (All the data listed

below are for reference only.)

Bit stream

size（max）

File size

Bit stream size

（max）

File size

96K

42M

128K

56M

160K

70M

192K

84M

224K

98M

256K

112M

320K

140M

384K

168M

448K

196M

512K

225M

640K

281M

768K

337M

896K

393M

1024K

450M

1280K

562M

1536K

675M

1792K

787M

2048K

900M

3072Kbps

1350M

4096K

1800M

6144Kbps

2700M

8192Kbps

3600M

Note

All information listed in the above sheet for reference only. We are not reliable for any

damage or loss resulting from it.

For the space marked by the HDD manufacturer, 1K=1000, while for the computer OS,

1K=1024. So, the space recognized by the computer system is less than the marked space

on the HDD. Please pay attention to it.

All HDD space marked by the HDD manufacturer is shown as below: 1T=1000G, 1G=1000M,

1M=1000K, 1K=1000.

All HDD space marked by the HDD manufacturer shall become the computer OS space after

the corresponding calculation. For example:

1T（marked by the HDD manufacturer）=1000G/（1.024*1.024*1.024）=931G（OS space），

500G=500G/（1.024*1.024*1.024）=465G

1.4.2 HDD Installation

Important

Shut down the device and unplug the power cable before you install the HDD.

Always use the HDD for the surveillance product recommended by the manufacture.

All figurers listed below for reference only. Slight difference may be found on the

front or rear panel.

Please note the following contents are based on our 2U/3U series product. For

detailed operation instruction of other series products, please refer to the User’s

Manual included in the resources CD.

You can refer to the User’s Manual for recommended HDD brand. Please follow the instructions

below to install hard disk. This series DVR max supports 8 SATA HDDs. Please use HDD of

7200rpm or higher.

1.4.2.1 2U Series

①Loosen the screws of the upper cover and remove

the cover.

②Fix the HDD on the bracket. If you want to install the HDD

on the bottom bracket, you need to remove the top bracket

first.

③Connect one end of the HDD data cable to one

HDD.

④Connect the other end of the HDD data cable to the

mainboard.

⑤Connect the power cable to the HDD.

⑥Put the cover back and then fix.

1.4.2.2 3U Series

①Remove the HDD box from the device.

②Put the HDD to the box and then use the screws to

secure.

③Insert the HDD box to the device. Please make sure

the HDD box handle is up in case it collides with the front

panel.

④After you inserted the HDD box, put the handle back.

Important

You can connect the HDD data cable and the power cable first and then fix the HDD in the

device.

Please pay attention to the front cover. It adopts the vertical sliding design. You need to

push the clip first and then put down.

1.5 Rack Installation

Please note this installation mode is for 1.5U/2U series product.

Please follow the steps listed below.

Use twelve screws to fix the unit

Please make sure the indoor temperature is below 35℃(95°f).

Please make sure there is 15cm (6 inches) space around the device to guarantee sound

ventilation.

Please install from the bottom to the top.

If there are more accessories connected in the rack, please take precaution measures in

case the rack power is overload.

1.6 Front Panel

For detailed operation instruction, please refer to the User’s Manual included in the

resources CD.

1.7 Rear Panel

Please note the following contents are based on our 2U series product. For detailed

operation instruction of other series products, please refer to the User’s Manual included

in the resources CD.

This series DVR rear panel is shown as below. See Figure 1-1.

Figure 1-1

Please refer to the following sheet for detailed information.

1. Video output

2. Audio output

3. Bidirectional talk

output

4. Bidirectional talk

input

5. Audio input

6. Alarm input/alarm

output

7. Video VGA output

8. RS-232 port

9. Power socket

10. Power switch

11. GND

12. HDMI port

13. USB port

14. eSATA port

15. Network port

16. Video input

Important

When connect the Ethernet port, please use crossover cable to connect the PC and use the

straight cable to connect to the switch or router.

1.8 Connection Sample

Please note the following contents are based on our 2U series product. For detailed

operation instruction of other series products, please refer to the User’s Manual included

in the resources CD.

Please refer to Figure 1-2 for connection sample.

The following figure is based on the 16-channel series product.

Figure 1-2

1.9 Alarm Input and Output Connection

Please read the followings before connecting.

1. Alarm input

a. Please make sure alarm input mode is grounding alarm input.

b. Grounding signal is needed for alarm input.

c. Alarm input needs the low level voltage signal.

d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)

e. When you are connecting two DVRs or you are connecting one DVR and one other device,

please use a relay to separate them,

2. Alarm output

The alarm output port should not be connected to high power load directly (It shall be less than

1A) to avoid high current which may result in relay damage. Please use the co contactor to

realize the connection between the alarm output port and the load.

3. How to connect PTZ decoder

a. Ensure the decoder has the same grounding with DVR, otherwise you may not control the PTZ.

Shielded twisted wire is recommended and the shielded layer is used to connect to the grounding.

Table des matières

Autres manuels Inaxsys DVR

Inaxsys

Inaxsys LEGEND Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur