Iluminarc Ilumipod Inground Tri-12 IP Manuel utilisateur

Ilumipod Inground

Tri-12 IP

Quick Reference Guide

Ilumipod Inground Tri-12 IP

What is

Included

•One Ilumipod Inground Tri-12 IP

•Concrete installation sleeve •One Warranty Card

•One Quick Reference Guide

About this

Guide

The Ilumipod Inground Tri-12 IP Quick Reference Guide (QRG) only

contains the product

’s connection and mounting information as well as the

menu options and the DMX values.

This QRG does not replace the

product’s user manual. You must download the user manual

from the

ILUMINARC® Web site (www.iluminarc.com) to learn about the

disclaimers, safety notes, programming modes and technical information.

Product at a

Glance

Use on Dimmer

Auto Programs

Outdoor Use P

Auto-ranging power

supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable x

Master/Slave

Duty Cycle

Features

•Remote addressable DMX-512 LED inground wash light

•Operating modes:

1-channel: Dimmer

3-channel: RGB control

4-channel: RGB, dimmer

6-channel: RGB per module

7-channel: RGB, dimmer, macro, strobe, dimming speed

•Blackout/static/dimmer/strobe/pulse

•IP67 ingress protection

•High power 3 W (1,050 mA) tri-color LEDs

•IP67 stainless steel gland nuts for cable entry

•Adjustable module angle

•Cast aluminum and stainless steel housing

•Impact resistant glass lens cover (drive-over rated)

•

Polished stainless steel mounting ring

Options

•Ilumicode compatible

•ILUMICON compatible

•Installed (non-changeable) optical system:

lenses P/N: 11012001

Ilumipod Inground Tri-12 IP

Installation

Notes

The Ilumipod Inground Tri-12 IP consists of

two parts, the fixture housing

and the concrete installation sleeve

. The fixture housing is IP67 rated, but

the

sleeve is not. Please pay close attention to the installation instructions

for the concrete installation sleeve regarding leveling and drainage.

You will have to run the AC power and signal cables into the concrete

installation sleeve and the fixture’s hou

sing. Do not use the fixture’s

junction box to extend the power or signal cables

to other units because it

may compromise the IP rating of the junction box. Instead, use individual

cables from the fixture to the corresponding distribution boxes.

Always kee

p the power cables away from the signal cables by running them

in different conduits and using separated distribution boxes.

Installation

Sleeve

Orientation

Orient the installation

sleeve to allow the signal

cable to enter the sleeve

using one of

the four cable

inlets and the power cable

to use the opposite inlet

, as

seen in the figure

. This

will reduce the stress to

the signal and power

cables when installing the

fixture, while keeping

them separated.

Installation

Sleeve Setup

When setting up the installation sleeve, make sure that any water that may

have entered it can drain out of the sleeve on its own. Locate the

installation

sleeve above the normal drainage level so the fixture

does not become

submerged in more than 1 m of water (IP67) during heavy rain.

In addition, make sure that the installation sleeve allows the stainless steel

collar to be leveled and flushed with the ground

surface to distribute the

load uniformly over the fixture’s surface.

Installation Sleeve

Drainage

The Ilumipod Inground Tri-12 IP can support a distributed load of up to

3,000 kg (6,614 lbs) when properly installed.

Ilumipod Inground Tri-12 IP

Beam Angle

Adjustment

The Ilumipod Inground Tri-12 IP has two LED modules. You can adjust the

angle of each of these modules to spread or narrow the fixture’s beam. To

do so, follow these steps:

•Loosen the ¼ turn Allen bolts on the stainless steel collar.

•Lift the fixture from the installation sleeve, making sure not to stretch

the power and signal cables.

•Loosen the six nuts that hold the collar to the housing, except two

adjacent ones.

•

Wait a few seconds for the seal to expand. This lowers the possibility of

damaging the seal.

•Complete the removal of the two remaining nuts.

•Remove the stainless steel collar.

•Carefully, lift and remove the protective glass and seal. Make sure not

to reverse the glass.

•Using only your hands, push on the sides of each module to adjust its

angle, as shown in the figure below.

•Replace the glass and seal.

•Replace the stainless steel collar, making sure to allow the Allen screws

to show and that the glass is flushed with the collar.

•Replace all six nuts and adjust them manually until they touch the

housing.

•Tighten the nuts uniformly by alternating between opposite nuts.

•

Reattach the fixture to the installation sleeve.

Ilumipod Inground Tri-12 IP

AC Power

This product has an auto-

ranging power supply that can work with an input

voltage range of 100~240 VAC, 50/60 Hz.

Junction

Box

This fixture has an IP67 rated junction box where the power and signal

cables come into the unit. The cables access the junction box through

individual (signal and power) IP67 rated stainless steel gland nuts.

Make sure that the junction seal is clean befo

re placing the cover back on.

In addition, tighten the gland nuts and the junction cover

to prevent water

from entering the junction box and cause a short.

The figure below shows the connections in the junction box.

Power

Wiring

To provide AC power to this fixture, you must run a single STJW rated, 3-

conductor cable (AWG18/3, 6~8 mm external diameter) from the power

distribution box into the installation sleeve and the fixture’s junction box.

Make sure to s

trip the end of the AC

power

cable that will connect to the

junction box as indicated in the figure

on the right.

Power Cable Table

Connection Wire (US) Wire (Europe)

AC Live

Black

Brown

AC Neutral White Blue

AC Ground

Green/Yellow

Signal

Wiring

To provide signal to this fixture, you must run a single, IP67 rated DMX

signal cable (shielded, 2-conductor, AWG24/2

, 6.5 mm external diameter)

from the signal distribution box into the installation sleeve and the fixture’s

junction box. The signal cable

must match or exceed the electrical

characteristics of the Belden® 9841 cable for EIA RS-485 applications.

VERY IMPORTANT

Make sure to use power and signal cables with the indicated outer diameters

to ensure that the corresponding gland nut makes full contact with the

cable’s external insulation. This is required to ensure watertightness once

fully adjusted.

Ilumipod Inground Tri-12 IP

Power

Distribution

You must connect the bare-ended power cable from the fixture to a

power

distribution box. If you choose to bury the power distribution boxes

, make

sure that they are IP67 rated.

Power Distribution

Box Wiring

Signal

Distribution

You must connect the bare-ended signal cable from the fixture to a signal

distribution box.

If you choose to bury the signal distribution boxes, make

sure that they are IP67 rated.

Signal Distribution

Box Wiring

Ilumipod Inground Tri-12 IP

DMX

Controller

The Ilumipod Inground Tri-12 IP

can work with a standard DMX

controller. The channel assignments will depend on the chosen personality

(see Menu Options

) and the DMX address assigned to each fixture (see

Settings).

The figure below illustrates how to connect the DMX controller to the

Ilumipod Inground Tri-12 IP fixture(s).

DMX Controller

Connection

ILUMICON

The Ilumipod Inground Tri-12 IP can also work with the ILUMICON

controller instead of a standard DMX controller. Please refer to the

ILUMICON user manual to learn how to use it with this fixture.

The figure below illustrates how to connect the ILUMICON controller to

the Ilumipod Inground Tri-12 IP fixture(s).

ILUMICON

Controller

Connection

Ilumipod Inground Tri-12 IP

Settings

The Ilumipod Inground Tri-12 IP

uses the Ilumicode unit for configuration

purposes.

Ilumicode

Connection

The diagram below shows how to connect the Ilumicode to this product.

Note that this connection will control multiple fixtures at the same time,

all having the same DMX address. To assign individual DMX addresses to

each fixture, you must connect the Ilumicode unit to each fixture,

individually.

Ilumicode

Connection

Diagram

ILUMINARC® suggests you to connect no more than 20 fixtures in this

mode and to keep the total distance to less than

60 m (197 ft). Otherwise,

you might need to use an optically isolated signal amplifier.

Ilumicode

Description

Button Function

<MENU>

Exits from the current menu or function

<ENTER>

Enables the currently displayed menu or sets the currently

selected value into the selected function

<UP>

Navigates upwards through the menu list and increases the

numeric value when in a function

<DOWN>

Navigates downwards through the menu list and decreases the

numeric value when in a function

Ilumipod Inground Tri-12 IP

Options

1ST Level 2nd Level 3rd Level Instructions

DMX 001~512 N/A Sets the DMX starting address

PERSON

ARC 1

N/A

3-channel: RGB control

ARC 1 + D 4-channel: RGB + dimmer (D)

ARC FULL 7-channel: RGB, D, macro, strobe,

speed

REMOTE The fixture operates with

ILUMICON

SOLID 1-channel: D

SPECIAL 1 6-channel: RGB per module

CALIB

WHITE

1~11

RED

000~255

Defines the White color

temperature used in

Macros

GREEN

RGBTOW

(1) Defines the white color

used in RGBTOW (2)

BLUE

DIMMER

OFF

N/A

The dimmer works in linear mode

DIM 1~4 The dimmer works in non-linear

mode, from fast (DIM1) to slow

(DIM4).

STATIC

RED

000~255 Combines RGB values to form a

static color

GREEN

BLUE

STRB 00~20 Sets the strobe frequency (0~20 Hz)

SETTINGS

COLOR

OFF When RGB = 255, output is

maximum

RGBTOW

(2) When RGB = 255, output is the one

defined in RGBTOW (1)

UC When RGB = 255, output matches

older models of the same fixture

RESET NO

YES

Ilumipod Inground Tri-12 IP

DMX Values

ARC FULL

Channel

Function

Value

Setting

Dimmer

000 ó255

0~100%

Red

000 ó255

0~100%

Green

000 ó255

0~100%

Blue

000 ó255

0~100%

5 Color Macro + White

Balance

000 ó010

011 ó030

031 ó050

051 ó070

071 ó090

091 ó110

111 ó130

131 ó150

151 ó170

171 ó200

201 ó205

206 ó210

211 ó215

216 ó220

221 ó225

226 ó230

231 ó235

236 ó240

241 ó245

246 ó250

251 ó255

No Function

Red 100% - Green Up - Blue 0%

Red Down - Green 100% - Blue 0%

Red 0% - Green 100% - Blue Up

Red 0% - Green Down - Blue 100%

Red Up - Green 0% - Blue 100%

Red 100% - Green 0% - Blue Down

Red 100% - Green Up - Blue Up

Red Down - Green Down - Blue 100%

Red 100% - Green 100% - Blue 100% - White 100%

White 1: 3,200 K

White 2: 3,400 K

White 3: 4,200 K

White 4: 4,900 K

White 5: 5,600 K

White 6: 5,900 K

White 7: 6,500 K

White 8: 7,200 K

White 9: 8,000 K

White 10: 8,500 K

White 12: 10,000 K

6 Strobe

000 ó004

005 ó255

No Function

0~20 Hz

7 Dimming Speed

000 ó009

010 ó029

030 ó069

070 ó129

130 ó189

190 ó255

Dimmer is set by Ilumicode

OFF (Dimmer is linear)

DIM1 (Fastest dimmer curve)

DIM2

DIM3

DIM4 (Slowest dimmer curve)

Autres manuels pour Ilumipod Inground Tri-12 IP

Table des matières

Autres manuels Iluminarc Équipement d'éclairage

Iluminarc

Iluminarc Ilumipod Inground Tri-12 IP Manuel utilisateur

Iluminarc

Iluminarc Colorist POD 18Qa Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 180 Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 180 Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 40 Manuel utilisateur

Iluminarc

Iluminarc COLORIST LINE 12Qa Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 90 IP Optic RGB Manuel utilisateur

Iluminarc

Iluminarc Ilumipod 18g2 IP Optic RGB Manuel utilisateur

Iluminarc

Iluminarc ILUMIPOD LL Manuel utilisateur

Iluminarc

Iluminarc Ilumiline 36 Manuel utilisateur

Iluminarc

Iluminarc ILUMIPOD ML Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 40 IP Optic WW Manuel utilisateur

Iluminarc

Iluminarc IP Series Manuel utilisateur

Iluminarc

Iluminarc Colorist Panel 8Qa Manuel utilisateur

Iluminarc

Iluminarc Colorist Panel 8Qa Manuel utilisateur

Iluminarc

Iluminarc Logic MR16 DN S Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 28 Manuel utilisateur

Iluminarc

Iluminarc ILUMIPANEL 24g2 IP Manuel utilisateur

Iluminarc

Iluminarc Ilumipod 18g2 IP Optic RGB Manuel utilisateur

Iluminarc

Iluminarc LOGIC DRIVE 2X Manuel utilisateur

Iluminarc

Iluminarc Ilumiline 36 Manuel utilisateur

Iluminarc

Iluminarc ILUMIPANEL LL Manuel utilisateur

Iluminarc

Iluminarc Ilumipanel 90 IP Optic RGB Manuel utilisateur

Iluminarc

Iluminarc Logic 16 x 36 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur