illuminfx COLOR SELECT PLUS Manuel utilisateur
QUICK GUIDES
COLOR SELECT PLUS
HOW TO
Add
Lighting Zones
The Color Select Plus system allows for additional zones to be added to the WiFi
104 system. Each zone requires a zone controller (CSP-R45ACV) to be added to the
system. This guide will help get these zone controllers integrated into the WiFi 104.
STEP ONE > find your wifi 104 device on the ‘device list interface’
After you open your Wifi 104 app, it will default to the ‘Device List Interface’
screen. Here it will list all available WiFi 104 modules to connect to.
STEP TWO > configuring anew zone on the wifi 104
To the right side of the listed WiFi 104 that you wish to add a zone to, is a
small icon that reads ‘Zone’
Select ‘Zone’ and continue to step 3 of this guide.
STEP THREE > zone set interface
The ‘Zone Set’ interface will list all 12 available zones that can be added to
the WiFi 104 system. As default, only ZONE 1 is set to be on.
*Optional - You can name each zone if you wish under the ‘Zone name’ category by simply
clicking on it and typing whatever you wish the name to be. This can be helpful to remember
which zones are which.
STEP FOUR > setting up anew zone
To turn on an additional zone, it is important to first set which type of zone
it is. To do this click on the ‘Type’ button for the zone (ex. Zone 2) and that
will open up the ‘Select Type Interface’ for that zone. You then simply select
which type of lights you are controlling on that zone from the list it provides.
STEP FIVE> linking that new zone
Finally, you just need to tell the device to enable that new zone you just set
up. To do this, click the ‘LINK’ for that zone (ex. Zone 2). This will move the
little slider over, and it will change the color to green.
Finally click on the Back button (labeled Return on the diagram).
*As shown in the Zone Set Interface diagram, a Zone that is turned off with have the slider to
the left and it will be grayed out.
To begin, open up your WiFi 104 APP on your smart phone.
Setting up Additional Zones
STEP SIX > getting to the main screen of the wifi 104 device
Now back at the main Device List Interface, you want to click on the
WiFi 104 Device you just added a zone to. Click on it where it says
CLICK HERE on the diagram to the right.
STEP SIX > physically linking the zone controller to the wifi 104 app
Now the main control screen for the WiFi 104 will be on your device.
Now that an additional zone has been added, you will see more than one Zone available (see section (2) on the diagram
below) You can have up to 12 available zones.
To connect the physical zone controller to your device, you will need to have access to the Zone Controller itself.
a. With a small screw driver, remove the protective plastic panel cover the one side of the Zone Controller (the side
with low voltage power going into it) This will reveal thee ID learning button (see diagram below labeled (1))
b. Now, on your device, select the zone you wish to set up (ex. Zone 2). It will highlight in Blue when it is selected.
c. On the Zone Controller, press the ID learning button and release. You will hear a beep and the light will stop blinking.
d. On your device, sweep your finger along the color bar (labeled (3) on the diagram below) until you hear another beep
from the Zone Controller.
e. The light on the Zone Controller will begin flashing and you will be all set up!
*Remember to replace the protective cover back onto the zone controller.
CLICK HERE
FOR MORE INFORMATION
Contact illuminFx Lighting Systems: illuminFx reserves the right to make changes
to specifications at any time with or without notice
(585) 254 - 8010
www.illuminfx.com
Table des matières
Autres manuels illuminfx Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
