iLight DALI Control Panel Manuel utilisateur
Introduction
The DALI control panel provides complete
control of pre-programmed lighting scenes
within a DALI lighting control system. The
adaptable design allows you to choose from
a range of button combinations, which can be
tted and changed at any time. Where tted,
raise and lower buttons compliment the usual
selection buttons to allow immediate changes
to the intensity of any scene.
Dimensions
The DALI control panel ts into a single gang
UK style wall box with a minimum internal
depth of 47mm.
With control panel disassembled (see above),
use the two supplied long screws to secure
the back plate to the wall box.
Fixing to a wallbox
Care and Maintenance
The front cover plate should only be cleaned
gently with a clean, damp cloth. Abrasive
cleaners, polishes, solvent based cleaning
agents, or alkali based cleaners should not be
used.
Installation guide
DALI Control Panel
Front Cover
Back Plate
Button Assembly
Screw holes for attaching
to wall box
Cooper Lighting Solutions iLight Product Series CLD DALI 9850-000521-01 2
1. On the underside of the face plate, beneath
the lower buttons, locate the small central
recess. Carefully insert a small implement (such
as a pen or screwdriver) into the recess and
lever the front cover gently away from the back
plate.
Removing Face Plate from the DALI Control Panel
Changing buttons
The DALI control panel allows you to change the
buttons in order to customize its appearance.
1. Remove the face plate as illustrated.
2. Locate the four clips (two on each side) of the
button frame. Carefully press in all four clips to
disenage the button frame and pull the frame
away from the main body.
3. You can now remove the buttons from the
frame and replace them (and the frame), as
necessary.
4. With the new buttons in place within the
frame, align its clips with the four holes of the
main body and press it into place so that all four
clips click as they lock.
3. Store face plate safe from damage.
2. Unclip the face plate from the back plate.
Cooper Lighting Solutions iLight Product Series CLD DALI 9850-000521-01 3
Control wiring
The DALI Control Panel is provided with 2 x polarity-free wires used to connect to the DALI line.
Standard Recommended DALI cabling: 2-core cable of minimum gauge 1.5 mm2.
The total cable distance: 300m.
2 x polarity-free wires
Typical DALI line schematic
DALI Bus
iCANnet
SOURCE CONTROLLER
SCMD4
DALI DINRAIL
SOURCE CONTROLLER
DALI
CONTROL
PANEL
CONTROL
PANEL
DALI
MULTI
SENSOR
DALI
DAC
0-10V VDC
DALI
DIMMABLE
BALLAST
DALI
RELAY
CONTROLLER
Max. 64 devices
per DALI loop.
Max. length 300M
1.5mm2 cable
Scene Selection
To select a scene press one of the buttons
identied by either a number, indicated by a
specic legend or that is blank.
To turn lights off press the button marked Off or
O on button only panels or the light bulb symbol
on control panels tted with the ‘On, Off, Raise
and Lower’ button set.
To raise the level of scene press (when tted).
To lower the level of scene press (when tted).
‘Scene Only’ control
panel example
Control panel tted
with ‘On, Off, Raise,
Lower’ button set
Document: 9850-000521-01
Cooper Lighting Solutions
Usk House, Lakeside, Llantarnam Park,
Cwmbran, NP44 3HD, UK
t: +44 (0)1923 495495 e: [email protected]
www.cooperlighting.co.uk
iLight Technical Support
Tel: +44 (0)844 324 9100 (available Mon-Fri 9am-5pm GMT)
Email: [email protected]
Web: www.iLight.co.uk
All products manufactured by Cooper Lighting Solutions and identied with the iLight product series
mark are warranted to be free from defects in material and workmanship and shall conform to
and perform in accordance with Seller’s written specications. For detailed warranty information,
contact Cooper Lighting Solutions.
This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods
found to be defective, upon their authorized return to Seller. This limited warranty does not apply
if the goods have been damaged by accident, abuse, misuse, modication or misapplication, by
damage during shipment or by improper service.
There are no warranties, which extend beyond the hereinabove-limited warranty,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS.
No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the
Seller or to assume for the Seller any other liability in connection with any of its goods except in
writing and signed by the Seller. The Seller makes no representation that the goods comply with
any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s
responsibility.
The use of the Seller’s goods should be in accordance with the provision of the National Electrical
Code, UL and/or other industry or military standards that are pertinent to the particular end use.
Installation or use not in accordance with these codes and standards could be hazardous.
FM 664349
Ce manuel convient aux modèles suivants
1
Autres manuels iLight Panneau de contrôle
