IGT Cobalt 27 Manuel utilisateur

Cobalt™ 27

Service Manual

90-200028-01

Georgia

Cobalt™

March 2020

Technology Training & Support Services

10 Memorial Boulevard, Providence, RI 02903 USA

Cobalt™ 27 Service Manual

SOFTWARE AND HARDWARE FEATURES MENTIONED IN THESE MATERIALS MAY NOT BE AVAILABLE IN

YOUR JURISDICTION, BUT ARE MENTIONED FOR TRAINING PURPOSES ONLY.

Warranty

Information in this document is subject to change without notice and does not represent a commitment on the part of IGT, a

wholly owned subsidiary of IGT. No part of this manual may be reproduced or transmitted in any form or by any means,

electronic or mechanical, including photocopying and recording, for any purpose other than the purchaser's personal use

without written permission of IGT.

Nothing contained in this document shall be construed as a warranty. The warranty, if any, for a product shall be contained

in the contract with IGT for the purchase, lease or license of the product. ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE HEREBY DISCLAIMED. IN NO EVENT SHALL IGT BE

LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, INCLUDING BUT

NOT LIMITED TO LOSS OF USE, REVENUE OR PROFITS.

Hardware Warning!

The following servicing instructions and/or information is for use by QUALIFIED PERSONNEL ONLY.

Systems Trademark and Copyright Information

Each and every use of an IGT trademark contained herein is intended to be protected and all rights are reserved.

Third-Party Trademarks

All other trademarks and registered trademarks are the property of their respective owners, without intent to infringe.

Hardware Trademark and Copyright Information

Certain trademarks and/or service marks used herein are the property of their respective third party owners. The use of

such marks herein is for identification purposes only, and does not imply an endorsement by IGT of the mark owner, or

vice-versa, or that such mark owner has authorized IGT to promote its products and/or services.

Contact Information

IGT

10 Memorial Boulevard

Providence, Rhode Island 02903

1-401-392-1000

IGT Support

1-866-777-8448

We Appreciate Your Ideas!

Was this material effective? Was it structured in a way that worked for you? Do you have ideas for making it

better?

Help the IGT team hit the jackpot. Please send your feedback to Support@igt.com Give it to us straight – We

appreciate your input.

2 Cobalt™ 27

Table of Contents

Safety 7

Chapter 1 Cobalt Overview 9

Cobalt Features 10

Specifications 11

Environmental Specifications 11

Electrical Specifications 11

Physical Specifications 11

Dimensions 12

Dimensions - with Topper 13

Dimensions - with Doors Open 14

External Components Overview 15

Cabinet Components 15

Player Panel Components 16

Lower Door Components 17

Basic Operational Instructions and Features 17

Security 17

Opening the Main Door 18

Opening the Lower Door 19

Opening the Cash Box Door 20

Accessing the Brain Box Secure USB Port 20

Door Monitoring 21

Internal Components Overview 22

Mutha Goose System Hardware 23

Cashless System Hardware 23

Powering On 24

Cobalt Access Levels 25

Chapter 2 Hardware 27

LCD Displays 28

Main LCD Display 29

Top LCD Display 30

On Screen Display (OSD) 30

LCD Removal 31

AC Box 32

AC Box Removal 32

Power Supply 33

Power Supply Removal 34

AVP 4+ Brain Box 36

Brain Box Removal 38

Cobalt™ 27 3

Cabinet Controller Board 39

Cabinet Controller Board Connectors 41

Switches 43

Cabinet Controller Board Removal 43

Audio Amplifier Board 44

Audio Amplifier Board Removal 44

Player Panel 45

Speakers 46

USB Charging Port 46

Bill Validator and Printer Bezels 46

Cashout Button 47

Button Panel 47

Player Panel Removal 48

Cashout Button Removal 50

Bezel LED Board Removal 50

Cabinet Lighting 51

LED Control Boards 51

Air Filters 53

Air Filter Maintenance 53

Hard Meters 54

Fledging Board 55

Fledging Board Connectors on Cabinet Controller Board 56

Fledging Board Removal 57

Cashless System Components 58

SMIB Module 58

C-Lite Interconnect Board 61

Card Reader 63

Bill Validator Theory of Operation 65

UBA® Bill Validator 65

UBA Bill Validator Components 66

UBA Bill Validator Connectors & Sensors 67

UBA Bill Validator Removal 68

UBA Bill Validator Error Codes 69

Nanoptix PayCheck 4™ Printer 71

Nanoptix PayCheck 4 Printer Components 71

Nanoptix PayCheck 4 Printer Connectors and Sensors 72

Nanoptix PayCheck 4 Printer, Loading Paper 73

Nanoptix PayCheck 4 Printer, Clearing Paper Jams 74

Nanoptix PayCheck 4 Printer Status Codes 75

Nanoptix PayCheck 4 Printer Removal 75

Chapter 3 Power Distribution 77

Power Distribution Overview 77

Power Distribution 78

Chapter 4 Installing Software & Clearing Memory 79

Program Installation 80

Requirements 80

BIOS and AP Chip Installation Steps 81

Software Installation Steps 83

Clearing Memory 84

Master Reset 84

4 Cobalt™ 27

CFInit 85

Appendix A Stand Mounting 87

Cobalt™ 27 5

6 Cobalt™ 27

Safety

This section contains safety precautions that should be reviewed and followed when troubleshooting

any IGT machine. It includes safety precautions that pertain to all IGT products.

General Safety Precautions

lFollow all applicable local electrical codes. Check to ensure that adequate power is available

based on the requirement(s) of the system being installed.

lAlways ensure that the electrical outlets are correctly wired and properly grounded. Polarity

and ground testers are available from most electronic stores. Test all outlets in the work area

before working on any electrical equipment. If there are any doubts about the wiring in the

work area, consult a qualified electrician.

Never use an adaptor plug to connect a three-prong power plug to a two-prong wall

outlet. Adaptors defeat the ground pin and eliminate the grounding protection.

lWhen working with either AC or DC voltage, take care not to touch the wires or circuitry to

each other or any other point of contact, including yourself. Use only approved test

equipment that is in good working condition.

lTurn off the power prior to connecting or disconnecting any electronic or electrical

components.

lTake precautions to protect sensitive electronic components from damage before moving

previously installed equipment.

lDisconnect the machine from all power sources before making changes to operating voltage

or frequency. Double check all electrical connections before applying power to avoid

permanent damage to the machine's electronic components.

lHandle all glass with extreme care to avoid breakage or injury from potentially sharp edges.

lBe cautious when handling all sheet metal to avoid injury due to sharp edges.

lVerify that the machine is securely bolted to a stand before beginning any work.

lReplace safety-critical components with the manufacturer’s recommended parts only.

lUse caution to keep hands clear of pinch points when closing doors.

Cobalt™ 27 7

Safety

Safety Messages

Safety messages are included in this manual and affixed to the product hardware. Safety messages

indicate:

lPotential hazard to the product or technician

lInstructions to reduce the chance of injury

lResults of not following the safety message instructions

Indicates that potential injury to the product or technician is possible if instructions are

not followed.

Indicates that serious injury or death may result if the instructions are not followed.

8 Cobalt™ 27

Chapter 1 Cobalt Overview

This manual describes the technical aspects of the Cobalt EGM. The information contained in this

document includes component identification, installation instructions, and preventive maintenance

practices.

This section describes the technical aspects of the Cobalt EGM including an overview of all of its

major components.

Topics include:

lCobalt Features on page 10

lSpecifications on page 11

lExternal Components Overview on page 15

lBasic Operational Instructions and Features on page 17

lInternal Components Overview on page 22

lPowering On on page 24

lCobalt Access Levels on page 25

Cobalt™ 27 9

Chapter 1 Cobalt Overview

Cobalt Features

lDual displays (27")

lIntelligent cabinet lighting

lPlayer Panel configuration(s):

oMechanical Button Panel with 5 buttons

lTopper (optional)

lHard Meters

lCashless System Components (optional)

Figure 1-1 Cobalt

10 Cobalt™ 27

Table des matières

Autres manuels IGT Machine de jeu d'arcade

IGT

IGT Crystal Slant Cabinet Manuel utilisateur

Manuels Machine de jeu d'arcade populaires d'autres marques

Universal Space

Universal Space COCONUT BASH Manuel utilisateur

Bay-Tek

Bay-Tek EVOLVE Manuel utilisateur

Global VR

Global VR America's Army Instructions d'installation et d'utilisation

Atronic

Atronic Cashline Manuel utilisateur

Universal Space

Universal Space Checky Monkey Manuel utilisateur

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Manuel utilisateur

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Manuel utilisateur

Family Fun Companies

Family Fun Companies Reactor Guide de démarrage rapide

Universal Space

Universal Space FRUIT MANIA Extreme Manuel utilisateur

falgas

falgas CARRUSEL FIESTA Manuel utilisateur

Konami

Konami DanceDanceRevolution Manuel utilisateur

Bay-Tek

Bay-Tek quik drop Manuel utilisateur

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Manuel utilisateur

Adrenaline

Adrenaline Flying Tickets Instructions d'installation et d'utilisation

Swinks

Swinks Stern Pinball Ghostbusters Manuel utilisateur

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Manuel utilisateur

jakar

jakar SPEED CARS Manuel utilisateur

Carmelli

Carmelli HAT TRICK NG1015H Manuel utilisateur