IDS X64 Guide d'installation

X64 Wireless Training

IDS | Contents

Contents

Features ___________________________________________________________________________________________3

Wireless Hardware __________________________________________________________________________________4

IDS & Duevi integration PCB ___________________________________________________________________5

LED operation _______________________________________________________________________________5

Wireless Device Hardware setup________________________________________________________________6

Location 260 _______________________________________________________________________________________7

LED Keypad Instructions ______________________________________________________________________7

Adding Wireless Detectors_____________________________________________________________________7

Upon Sub menu entry the user will notice the following: ____________________________________________8

Delete Wireless Detectors _____________________________________________________________________9

Signal Power of Received Signal ________________________________________________________________9

Supervision monitoring _______________________________________________________________________10

Trouble Conditions _________________________________________________________________________________11

Reporting Codes ___________________________________________________________________________________12

Location 300 Global Reporting ________________________________________________________________12

Location 301 Global reporting _________________________________________________________________12

Location 302 Global reporting _________________________________________________________________13

Location 303 Global reporting _________________________________________________________________13

Location 304 to 335 Zone Reporting ___________________________________________________________14

Location 336 to 340 Keypad Reporting _________________________________________________________14

Location 342 to 373 User Reporting ___________________________________________________________14

Event Reporting ____________________________________________________________________________________15

Location 501 to 564 Global Split Reporting ______________________________________________________15

Location 571 Global Split Reporting ____________________________________________________________15

Location 572 Global Split Reporting ____________________________________________________________16

Location 573 Global Split Reporting ____________________________________________________________16

Location 574 Global Split Reporting ____________________________________________________________17

Location 575 Global Split Reporting ____________________________________________________________17

Appendix _________________________________________________________________________________________18

Wireless Installation Considerations ____________________________________________________________18

IDS | Features

Features

1. X64 is a hybrid system that can have wired and wireless zones

2. Wireless zone monitoring:

a. Supervision

b. Tamper

c. Low Battery

d. Low signal strength

3. Receiver Monitoring

a. RF Jamming

b. Tamper

c. Bus communication fail

4. Each wireless zone expander handles blocks of 16 sequential zones

5. Each receiver has two outputs which can be set to normal programmable output mode or trigger on supervision

and low battery when one of the zones it is monitoring has either of these conditions

6. Four types of wireless devices:

a. Indoor 18Kg pet immune PIR

b. Outdoor dual head PIR

c. Door mag. With an input that works in parallel to the reed switch

d. Outdoor PIR and microwave, E-wall

IDS | Wireless Hardware

Wireless Hardware

Warning

1. Older wireless hardware devices will not work with the X64, Duevi integration. Please make sure that you have

the correct version of each device.

2. The Duevi wireless peripheral device defaults are:

a. Tamper switches disabled.

b. Supervision time set to 24 hours on the following devices, 866-DX-PWF Wireless Door Contact, 866-DX-

PWF Indoor Wireless PIR

c. 90 minutes supervision time for 866-DX-OPWF Outdoor Dual Head PIR and the 866-DX-EWF E-wall

3. Supervision failure will occur when a device does not check in for the time set in; location 260 sub-location 3. The

zone will violate and remain violated until the device sends violation signal or a supervision signal.

a. Make sure that all devices are set to the correct supervision time.

For example: If the X64 is set to 24 hour supervision then each device can be set to 24 hour or 90

minute check-in, but if set to 3 hours then each device must be set to 90 minute check-

in.

4. Tamper per zone for wireless zones are set the same as wired zones in location 101 to 164 depending on which

zones are to be monitored.

5. Wireless receivers can monitor sixteen devices at a time in sequential blocks: zones 1 to 16, 17 to 32, 33 to 48

and 49 to 64. (How to set which receivers monitor which group of zones will be discussed later.)

For example: A wireless receiver configured to monitor zones 1 to 16 cannot see zone 17 or any other

zone that is not in the first sixteen zones, even if it has only one device learnt to it.

IDS | Wireless Hardware

IDS & Duevi integration PCB

1. DIP switch operation

The Dipswitch currently has only two operations. The first is to set the device address on the X64 bus. This is

done in binary the same as was done for the wired expander save for one difference. That is that these

expanders each cater for 16 zones and not 8 like the wired expander.

Zones 1 –16 Zones 17 –32 Zones 33 –48 Zones 49 - 64

Dip 1 Dip 2 Dip 1&2 Dip 3

Output configuration:

PGM 1= RF Jam PGM 2 = Supervision Loss

Note: When dip switch 5 and 6 are:

OFF the outputs are then programmable.

ON the outputs are by default set to output 1 RF jam and output 2 supervision loss

2. Default

The second operation is a standalone default feature. If all Dip-switches are ON during power-up then the unit will

default. Please power down after, set appropriate address and power up to resume normal operation.

LED operation

There are 3 LEDs on the board marked “MODE”, “RF RX” and “STATUS”.

MODE: LED that indicates current operating errors. Errors are indicated much the same as the

wired expander. If the LED is ON continuously then there are no errors. However if there are errors it will start

pulsing the error number. These error pulses will be separated by a 1sec pause with the LED OFF.

Pulse error number:

1. Duevi receiver module not responding

2. No activity on the X64 serial bus

3. No X64 messages detected

4. No messages for this peripheral detected from X64

5. Not used

6. Expander not yet registered on the X64

7. Expander tamper violated

8. Unsupported DIP address configured

RF RX: LED that will indicate when the receiver received a message from a learnt detector.

STATUS: LED that will indicate whether it is connected to the X64 properly. If the receiver notices X64

communications then it will stay ON.

Tamper

Dip Switches

LEDs

IDS | Wireless Hardware

Wireless Device Hardware setup

Note: The import thing to remember is that when you have chosen the supervision time of 3Hrs on

the X64 is to make sure the detectors are also set to 90min.

The correct hardware must be used as the older Duevi wireless detectors will not learn to the

integrated receiver

Duevi Outdoor Wireless Dual Head PIR - 866-DX-OPWF

Dip switch 5: On = 24 Hrs Off = 90 min

Default: 90 minutes check in

Note: To learn the dual PIR to the X64 first get both PIR heads to detect movement then press the tamper

switch when in location 260 sub location 1 and the correct zone number has been selected

Duevi Wireless Door Contact including input - 866-DX-PWF

JP2 jumper: On = 24Hrs Off = 90min

Default: 24 hours

Note: To learn the door contact to the X64 press the tamper switch when in location 260 sub location 1 and

the correct zone number has been selected

Duevi Wireless Indoor Wireless pet tolerant (small pet) PIR - 866-DX-PWF

SPV jumper: On =24Hrs Off = 90min

Default: 24 hours

Note: To learn the indoor PIR to the X64 press the tamper switch when in location 260 sub location 1 and

the correct zone number has been selected

Duevi Outdoor E-Wall with PIR & Microwave - 866-DX-EWF

Dip switch 4: On = 24Hrs Off = 90min

Default: 90 minutes

Note: To learn the door contact to the X64 press the tamper switch when in location 260 sub location 1 and

the correct zone number has been selected

IDS | Wireless Hardware

Location 260

Location 260 has a four sub locations listed in the table below:

Sub Location

Description

Add Wireless Device

Delete Wireless Device

Wireless Device Signal Strength

Supervision Interval Time

Note: Depending if you have an LED or LCD keypad will depend on the feedback you can expect to

receive while programming. The following instructions will be broken up into LED keypad, indicated

by and LCD keypad indicated by

LED Keypad Instructions

Upon Location entry the user will notice the following:

a. Ready LED ON, Armed LED ON, Away LED flashing.

b. Menu system now only awaiting sub location selection.

i. User must enter [number][*] to advance into “sub menu”.

c. When entering sub menus, I.e. add wireless device or delete wireless device.

Zones that are wireless zones will be on.

d. [#] will return user to Installer menu location entry.

LCD Keypad Instructions

Upon location entry the following will be displayed

Scroll backwards using Scroll forward using

using the Medical key the Panic key

Press * key

to enter

[#] will return user to Installer menu location entry

Adding Wireless Detectors

Upon Sub menu entry the user will notice the following:

When working with more than 16 zones on an LED keypad to page through to the next 16 zones press the [*] key

Note: Each time a new page of zones are shown the Pwr, Rdy, Arm and Away LEDs will change to show

which zones are being displayed.

Zones 1 to 16 Zones 17 to 32 Zones 33 to 49 Zones 49 to 64

Example:

Press

On On

Zones 1 to 16 Zones 17 to 32

Wireless zones 10 & 11 Wireless zones 19, 21 & 29

LED

LCD

LED

LCD

Flashing

LED

IDS | Wireless Hardware

1. Zone LEDs will be ON if the zone already has a wireless detector assigned.

The menu is now waiting for user to select to which zone to add a detector. If the user selects a pre-allocated

zone then the keypad will sound 3 error beeps and wait for a valid zone entry.

Note: Detectors may only be added on LED keypads via the tamper method.

2. Upon valid zone selection the keypad will sound an OK (single beep) and set the zone LED selected to start

flashing. The system is now waiting for the new detector to be tampered.

When the user triggers the tamper the system will receive a notification and determine whether the detector

has already been assigned to any other zones. If this is the case the user will be notified by 3 error beeps

and the menu will keep waiting for a tamper from an unassigned detector.

If the detector has not been assigned then it will be automatically added to the system. The user will be

notified via keypad by a LONG OK beep as well as the Zone LED previously flashing will now be ON.

3. The system will now wait for a new zone to be selected.

4. [#] key at any time will return the user back to the sub menu selection menu.

Upon Sub menu entry the user will notice the following:

Scroll using Medical or Panic Keys, Enter with [*] key

Or enter the zone number followed by the [*] key

[#] will return user to sub menu selection entry.

Example: If zone name still default

Example: If zone name has been changed to “Main Lounge”.

Selecting a zone that is a wireless zone already, will result in an error and the user will be alerted with 3 error

beeps.

1. Upon selecting a zone that is not already a wireless zone the user will be presented with the following.

2. Press enter to confirm zone selection

The user must now either trigger the tamper on the detector or key in the serial number of the device.

When the user triggers the tamper the system will receive a notification and determine whether the detector

has already been assigned to any other zones. If this is the case the user will be notified by 3 error beeps

and the menu will keep waiting for a tamper from an unassigned detector.

Incorrect or pre-allocated serial numbers will also result in a 3 beep error tone and the menu will keep waiting

for a valid entry.

3. Upon valid Serial Number entry or tamper the user will be presented with the following.

Press [*] to confirm the serial number is correct

LCD

IDS | Wireless Hardware

Delete Wireless Detectors

Upon Sub menu entry the user will notice the following:

Note: Each time a new page of zones are shown the Pwr, Rdy, Arm and Away LEDs will change to show

which zones are being displayed. Pages are scrolled using the [*] key.

Zones 1 to 16 Zones 17 to 32 Zones 33 to 49 Zones 49 to 64

Pages are scrolled using the [*] key.

1. Zone LEDs will be ON if the zone already has a wireless detector assigned to it.

The menu is now waiting for the user to select which zone they want to delete a detector from.

2. Zone LED will turn OFF on zone selection.

3. [#] key at any time will return the user back to the sub menu selection menu.

Upon entering location 260 and scrolling to or entering option 2 the following will be displayed:

Scroll using Medical or Panic Keys, Enter with [*] key

1. Enter [*] to enter the delete sub location to have the following displayed:

Scroll using Medical or Panic Keys, Enter with [*] key

Or enter the zone number followed by the [*] key

2. Enter the zone number or scroll to the zone.

Signal Power of Received Signal

NOTE: This menu is active for the LCD keypad only. The user will need to either trigger the tamper or zone to get

a signal power update.

Upon entering location 260 and scrolling to or entering option 3 the following will be displayed:

Scroll using Medical or Panic Keys, Enter with [*] key

1. Enter [*] to enter signal strength testing

Scroll using Medical or Panic Keys, Enter with [*] key

Or enter the zone number followed by the [*] key

2. Enter or scroll to the zone to be deleted

Scroll using Medical or Panic Keys, Enter with [*] key

Indicates that this zone is a wireless zone

3. Press the [*] key to select the zone

4. Trigger the device and the display will show the signal strength on the first row.

Signal strength displayed in percentage

LED

LCD

Autres manuels pour X64

Table des matières

Autres manuels IDS Système de sécurité

IDS

IDS X-Series X-SMS Manuel d'instructions

IDS

IDS X16 Guide d'installation

IDS

IDS Ezi4 Guide de l'utilisateur

IDS

IDS 400 Manuel utilisateur

IDS

IDS 816 Manuel utilisateur

IDS

IDS SMS Duo V2 Guide de configuration

IDS

IDS X Series Manuel utilisateur

IDS

IDS VX PRO Series Manuel d'exploitation

IDS

IDS X Series Manuel utilisateur

IDS

IDS X64 Manuel utilisateur

IDS

IDS X64 Mode d'emploi

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur