iDomotics Starter Kit Manuel utilisateur
QUICK INSTALLATION GUIDE
This product must be installed by a
licensed electrician or other suitably
qualied person.
IMPORTANT NOTE
Please read the following document
carefully before setting up and using your
IDOMOTICS device for the rst time.
4
content
Tools required
Controller
Sensor Network
cable
Domotic
Central
3 mm athead
screwdriver
Voltage tester
screwdriver
Stripping tool 0,5 or 0,75 mm cable
20 mm hole saw
Power source
7.5 volts
1 ampere
5
central
Connections
USB
Supply
Connect it to the Switch
or to your Router’s LAN port.
Network
cable
RJ-45 input
USB
Optional use
of power
supply.
For the use of
Technical
Personnel.
6
Connection of Light controllers
- Neutral cable inside the light box needed.
- Works with one or two lights.
- T1 corresponds to light 1, T2 to light 2.
Important: Do not connect the keys to the domestic
supply network.
| Connection of Light controllers
Conguration
button
Keys
connection
Electrical
connection
Domestic
network
21
7
Installation of Light controllers
For lament light bulbs, low energy bulbs, LED (110-
220V), uorescent tubes, dichroic bulbs (110-220V).
1. Dismantle the frame. If you use the light and tempera-
ture sensor, at least one blind module is required.
2. Identify the return conductor of the lamps and the line
or phase cable, using a voltage tester screwdriver. If you
can’t nd one, add a neutral cable, which will be neces-
sary for the performance of the controller.
-OPTIONAL-
3. Take the blind module o the frame and make a
20mm hole in the middle with the holesaw. A power
driver is recommended for this.
4. Disconnect the sensor’s module from the light
switch controller and press it onto the hole of the blind
module. We recommended gluing it in place with silico-
ne or multipurpose glue.
Extreme care: handling objects with electrical
voltage! Danger of electrocution!
Proceed only trained electrician or other suitably
qualied person. We recommend placing the
controller next to the light switch.
Installation of Light controllers |
8
5. Cut three cables with a maximum length of 8cm and
connect them to the corresponding terminal board of C,
T1 and T2 of the controller’s keys. It is recommended
that you do not strip the cable more than 5mm with the
cable stripper.
6. Disconnect the returns from the keys of the frame
and connect them to the terminals 1 and 2, and Line and
Neutral to the terminals L and N. Use a 3 mm athead
screwdriver.
N: Neutral cable
L: Line or Phase cable
1: Light return 1
2: Light return 2
See the installation diagram to verify the connections.
7. Connect the cables connected to the frame of the
light switch controller to the keys of the frame, then con-
nect the module to the sensors. (See diagram of connec-
tion of Light Controller)
C: Common
T1: Light controller 1
T2: Light controller 2
| Installation of Light controller
IMPORTANT. CUT THE ELECTRICITY OF THE RESIDENCE
BEFORE CONTINUING.
9
Introduce it in the metal case inside the wall but DO
NOT close it with the frame. Install the rest of the
controllers before continuing.
8. Connect the electricity of the residence and proceed
to install the central.
9. With the idomotics server installed and congured,
add the corresponding device. ( see page 13 of the User
manual)
Move the handle named ‘CONFIG’ on the light controller
to its opposite side.
Once you can see the ‘identier’ code on the congura-
tion of the device, close with (see page 14 of the User
manual)
10. You can now see and operate the controller on the
client app. Proceed to adjust the frame.
Installation of Light controllers |
LAN
Connect it to
the Switch
or Router’s LAN
port.
USB
Optional
connection for
power supply.
CENTRAL’S
BACK
SUPPLY
Connect it to
the plug with the
power source included.
10
Uses: Light Controller
How to connect it to the electric lock.
| Uses of light controller
Doorbell
button
Electrical
connection
Electric lock
which unblocks
the latch
Conguration
button
Domestic
network
Table des matières
