IDataLink ADS-MRR2 Manuel utilisateur

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁed technician. Logos and trademarks used here in

are the properties of their respective owners.

WARNING

Pressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll

down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced

options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE

SELECT VEHICLE

PRINT PAGES NEEDED

PRODUCTS REQUIRED

iDatalink Maestro RR or RR2 Radio Replacement Interface

iDatalink Maestro HRR-MA2 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-MA1-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

ELECTRONICS

Click here for:

Radar Installation Guides

20142017

MAZDA 3

TOUCHSCREEN

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁed technician. Logos and trademarks used here

in are the properties of their respective owners.

ANTENNA ADAPTER (MAY BE REQUIRED)

HEAD UNIT ADAPTER:

ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1

OPTIONAL ACCESSORIES

MAZDA 3 TOUCHSCREEN 20142017

WELCOME

NEED HELP?

Congratulations on the purchase

of your iDatalink Maestro RR Radio

replacement solution. You are

now a few simple steps away from

enjoying your new car radio with

enhanced features.

Before starting your installation,

please ensure that your iDatalink

Maestro module is programmed

with the correct ﬁrmware for your

vehicle and that you carefully review

the install guide.

Please note that Maestro RR will

only retain functionalities that

were originally available in the

vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Module Diagnostics 6

Troubleshooting Table 7

1 866 427-2999

maestro.idatalink.com/support

www.12voltdata.com/forum

[email protected]

MAZDA 3 TOUCHSCREEN 20142017

STEP 1

• Disconnect the negative battery terminal (not doing so

may blow the 7.5A audio fuse 2 under hood during the

installation of the radio).

• Remove the factory radio

If using head unit adapter (sold separately), connect HRR-

MA2 harness to adapter and skip to step 2.

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the black 20 pin connector from the HRR-

MA2 T-harness and connect the wires, shown in the wiring

diagram, from aftermarket radio main harness to the HRR-

MA2 T-harness and match the wire functions.

Note: only connect purple/white wire to radio reverse input

or module damage will occur.

STEP 2

If the vehicle DOES NOT have a factory ampliﬁer:

• Plug in the extension harness to HRR-MA2 main harness

8-pin black connector.

If the vehicle DOES have a factory ampliﬁer:

• Plug in the extension harness to 8-pin black connector of

RCA cable.

• Connect the RCAs to the radio outputs: white/left front,

gray/right front, green/left rear, purple/right rear.

• Route the extension harness to the radio tuner in the

passenger kick panel.

STEP 3

• Connect both the 18-pin and 28-pin connectors of HRR-

MA2 T-harness to the factory radio harness (at CMU,

behind/below display).

STEP 4

• Connect the 24-pin adapter (red connector) to the factory

radio tuner in the passenger kick panel.

• Connect the adapter’s 8-pin black connector to the

extension harness.

• Plug the blue POWER ANT terminal to ampliﬁed antenna

adapter (if required).

STEP 5

• Plug the harnesses into the aftermarket radio.

• Connect the backup cam cable into the aftermarket radio

(if equipped).

• Plug the antenna adapter (if required).

• Plug the Data cable to the data port of the aftermarket

radio.

Note: On Pioneer radio, ensure that there is nothing plugged

into the W/R port.

STEP 6

• Connect all the harnesses to the Maestro RR module.

• Reconnect the negative battery terminal then test your

installation.

INSTALLATION INSTRUCTIONS P1 /1

MAZDA 3 TOUCHSCREEN 20142017

BACKUP CAMBACKUP CAM

AMP TURN ONAMP TURN ON

POWER ANTPOWER ANT

AUDIO

CABLE

MICMIC

N.C. AMP TURN ONAMP TURN ON

POWER ANTPOWER ANT

MAESTRO RR MODULE

STEP 1

MAIN

HARNESS

HRR-MA2 T-HARNESS

STEP 5

STEP 6

WHITE - LF SPEAKER (+)

WHITE/BLACK - LF SPEAKER (-)

GRAY - RF SPEAKER (+)

GRAY/BLACK - RF SPEAKER (-)

GREEN - LR SPEAKER (+)

GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)

YELLOW - 12V (+)

BLACK - GROUND

RED - ACCESSORY (+)

BLUE/WHITE - AMP. TURN ON (+)

PURPLE - RR SPEAKER (+)

ORANGE - ILLUMINATION (+)

PURPLE/WHITE - REVERSE LIGHT (+) *

LTGREEN - E-BRAKE (-)

PINK - VEHICLE SPEED

WIRING DIAGRAM

STEP 2

CMU

TUNER

STEP 3

STEP 4

SEE RADIO WIRE

CHART

FOR RADIO WIRE

COLORS

DATA

CABLE

CONNECT TO

AFTERMARKET RADIO

NOT REQUIRED

STEERING WHEEL

CONTROL CABLE

PIONEER RADIO: ENSURE

THAT NOTHING IS PLUGGED

IN W/R PORT.

* ONLY CONNECT TO RADIO REVERSE INPUT

OR MODULE DAMAGE WILL OCCUR

TO ANTENNA

ADAPTER IF REQUIRED

WITH OEM AMP

WITHOUT OEM AMP

HEAD UNIT ADAPTER

SOLD SEPARATELY

IF WIRES ARE PRESENT ON

ADAPTER: SEE RADIO

REFERENCE CHART

IF NOT USING A MAESTRO HEAD UNIT ADAPTER:

CUT AND DISCARD CONNECTOR

LF OUT

RF OUT

LR OUT

RR OUT

CONNECT IF EQUIPPED *

PASSENGER KICK PANEL

BEHIND/BELOW RADIO DISPLAY

MAZDA 3 TOUCHSCREEN 20142017

RADIO WIRE REFERENCE CHART

MA2 T-harness

Wire Description Polarity Wire Color on Maestro

T-Harness

Wire Color on Alpine

cable

Wire Color on Kenwood

cable

Wire Color on Pioneer

cable

Wire Color on Sony

cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light* (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ACC-HU-KEN2

Wire Description

Polarity Wire Color on Adapter Kenwood Radio

E-Brake (-) LtGreen LtGreen

Reverse Light* (+) Purple/White Purple/White

Steering Wheel Controls (DATA) Blue/Yellow n/a

ACC-HU-ALP1

Wire Description

Polarity Wire Color on Adapter Alpine Radio

VSS (vehicle speed sensor) (DATA) Green/White Green/White

ACC-HU-KEN1

Wire Description

Polarity Wire Color on Adapter Kenwood Radio

CAM (+) Green/Red Refer to camera/radio

manual

CAM (-) Green/White Refer to camera/radio

manual

Steering Wheel Controls (DATA) Blue/Yellow n/a

Head unit adapter wiring (optional accessory, sold separately)

* Reverse light wire: Only connect to radio or module damage will occur.

MAZDA 3 TOUCHSCREEN 20142017

MODULE DIAGNOSTICS

VIDEO HELP Installation, product information, vehicle speciﬁc videos.

VERIFY FLASH Last ﬂash information, steering control conﬁguration, vehicle information.

WEBLINK Software to program module.

LED 1 LED 2

LED 1

PROGRAMMING BUTTON

LED 1

Module/Firmware

status

LED 2 (RR2)

Bluetooth activity

LED STATUS DIAGNOSTIC

• or •RED or GREEN

ﬂashing

LED ﬂashes 1 or more times, either red or green, when a steering wheel

button is pressed : normal operation.

•1 RED ﬂash Module has no ﬁrmware.

Flash module using Weblink Desktop and log in. Do NOT use DEMO MODE.

•2 RED ﬂashes Problem detected. Consult troubleshooting table.

•1 GREEN ﬂash After radio boots up : Normal operation.

•3 GREEN ﬂashes Bluetooth is activated.

Turns off after one minute: Normal operation.

• • OFF Normal operation (inactive).

MAZDA 3 TOUCHSCREEN 20142017

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. If anything is connected to the OBD2 or CAN wires of vehicle (programmer,

throttle controller, insurance tracker, etc.) try unplugging it to see if gauges

work. If gauges work without it installed, call tech support for options.

Reset the RR.

CX-5 and Mazda3

No audio after installing new radio. Factory radio no longer has sound.

Check 7.5 amp “AUDIO 2” fuse located under the hood.

The light on the Maestro is ﬂashing RED ONCE. There is no ﬁrmware on the module. Flash the RR module using Weblink

Desktop and log in. Do NOT use DEMO MODE.

The light on the Maestro is blinking RED TWICE and the radio IS turning on. Ensure the 4-pin data cable is connected between the radio and the RR, and

that it is plugged into the black port on the Maestro RR. The red and blue

ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during

the ﬂash. Verify the radio’s serial number entered during the ﬂash matches

what is listed on the radio screen. This can be found in the settings of the

radio, listed as Device Id, Device Number, or Serial Number.

The light on the Maestro is blinking RED TWICE but the radio is NOT turning

on.

If installing a modular radio and it is not turning on, ensure the screen is

secured and any trim pieces on the radio have been installed fully. Not

installing these fully will prevent radio from powering up and show a 2x red

error as well.

Test red and yellow wires for DC voltage at radio using a multimeter. Contact

support if no voltage on red or yellow.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module.

Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂash RED rapidly (this may

take up to 10 seconds).

Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE

Phone: 1-866-427-2999

Email: maestr[email protected]

Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest ﬁrmware from the manufacturer. Please visit the radio

manufacturer’s website and look for any updates pertaining to your radio.

PRODUCTS REQUIRED

iDatalink Maestro RR or RR2 Radio Replacement Interface

iDatalink Maestro HRR-MA2 Installation Harness

PROGRAMMED FIRMWARE

ADS-RR(SR)-MA1-DS

ADDITIONAL RESOURCES

Maestro RR2 Programmable Outputs Guide

ELECTRONICS

Click here for:

Radar Installation Guides

2018

MAZDA 3

TOUCHSCREEN WITH AMPLIFIER

INSTALL GUIDE

RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁed technician. Logos and trademarks used here

in are the properties of their respective owners.

ANTENNA ADAPTER (MAY BE REQUIRED)

HEAD UNIT ADAPTER:

ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1

OPTIONAL ACCESSORIES

MAZDA 3 TOUCHSCREEN WITH AMPLIFIER 2018

WELCOME

NEED HELP?

Congratulations on the purchase

of your iDatalink Maestro RR Radio

replacement solution. You are

now a few simple steps away from

enjoying your new car radio with

enhanced features.

Before starting your installation,

please ensure that your iDatalink

Maestro module is programmed

with the correct ﬁrmware for your

vehicle and that you carefully review

the install guide.

Please note that Maestro RR will

only retain functionalities that

were originally available in the

vehicle.

TABLE OF CONTENTS

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

Module Diagnostics 6

Troubleshooting Table 7

1 866 427-2999

maestro.idatalink.com/support

www.12voltdata.com/forum

[email protected]

Ce manuel convient aux modèles suivants

Autres manuels iDataLink Accessoires automobiles

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Pr 2 Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink Maestro K150 Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink Maestro RR Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink ADS-ALCA Manuel utilisateur

iDataLink

iDataLink Maestro RR Manuel utilisateur

iDataLink

iDataLink BLADE-AL-HK4-EN Manuel utilisateur

iDataLink

iDataLink Maestro RR Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink ADS-ALCA Manuel utilisateur

iDataLink

iDataLink ADS-TBSL-C1 Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink Maestro AR Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink maestro Rr Manuel utilisateur

iDataLink

iDataLink Maestro RR Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur

iDataLink ADS-MRR2 Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques