ICTeSecurity rf-rcvr-433 Manuel utilisateur
Wireless 433MHz Receiver
Installation Manual
2Wireless 433MHz Receiver | Installation Manual
The specifications and descriptions of products and services contained in this document were correct at the
time of printing. Integrated Control Technology Limited reserves the right to change specifications or withdraw
products without notice. No part of this document may be reproduced, photocopied, or transmitted in any form
or by any means (electronic or mechanical), for any purpose, without the express written permission of
Integrated Control Technology Limited. Designed and manufactured by Integrated Control Technology Limited.
Protege® and the Protege® Logo are registered trademarks of Integrated Control Technology Limited. All other
brand or product names are trademarks or registered trademarks of their respective holders.
Copyright © Integrated Control Technology Limited 2003-2018. All rights reserved.
Last Published: 17/01/2018 11:49
Wireless 433MHz Receiver | Installation Manual 3
Contents
1Introduction_______________________________________________________________ 4
2Mounting _________________________________________________________________ 5
3Installation Wiring _________________________________________________________ 6
4System Settings___________________________________________________________ 7
4.1Default Configuration.....................................................................................................7
4.2Default Operation ..........................................................................................................7
4.3Custom Operation Setup...............................................................................................8
5Programming Options______________________________________________________ 9
5.1Mode Programming Menu.............................................................................................9
5.2Quick User Programming ..............................................................................................9
5.3User Programming Menu ..............................................................................................9
5.4Site Code Programming Menu....................................................................................10
5.5Button Programming Menu .........................................................................................11
5.6Wiegand Programming Menu......................................................................................11
5.7Output Port Format Programming...............................................................................11
5.8PGM Programming Menu............................................................................................12
5.9Signal Strength Programming Menu ...........................................................................12
6Contact _________________________________________________________________ 13
4Wireless 433MHz Receiver | Installation Manual
1 Introduction
The Wireless 433MHz Receiver provides a fast and simple integration of ICT 4 or 2 button remote transmitters
into any alarm or access control system. The standalone functionality allows for easy, secure operation of gates
or other access areas where convenience is required.
The current features of the Receiver include:
4 operation modes: RS-232, Wiegand, standalone and output control
Per channel digital reception sensitivity using RSSI configuration
600 user (transmitter ID) capacity in standalone mode. Unlimited users in Wiegand pass through mode.
4 open collector programmable outputs
1 FORM C relay output
Wireless 433MHz Receiver | Installation Manual 5
2 Mounting
The Receiver must be mounted so that the antenna is vertical. If you are mounting the board on its side (as
shown in Option 2), turn the antenna 180 degrees so it is pointing up.
Option 1
NCCMNORXTX-+
ATP4P3P2P1
-
+
Enclosure
Option 2
NCCMNORXTX-+
ATP4P3P2P1
-
+
Enclosure
6Wireless 433MHz Receiver | Installation Manual
3 Installation Wiring
Output and Antenna Connection Wiring
+12V
0V
PGM 1
PGM 2
PGM 3
PGM 4
ANTENNA
From external power supply
Wiegand Port 1 D0
Wiegand Port 1 D1
Wiegand Port 2 D0
Wiegand Port 2 D1
Connect supplied whip
wire antenna
ATP4P3P2P1
-
+
Power and Relay Output Connection Wiring
+12V
0V
Relay output activation
controlled by selected
buttons
RS232 TX
RS232 RX
RELAY NO
RELAY COMMON
RELAY NC
From PC or other RS232
device, use these or
DB9 connector
From external power supply
NCCMNORXTX-+
Power and Relay Output Connection Wiring
Wireless 433MHz Receiver | Installation Manual 7
4 System Settings
4.1 Default Configuration
Default Mode: ICT Pass Through
RS232 Default Settings:
Baud Rate 9600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
Wiegand Default Settings:
Wiegand Port 1 26 Bit Unique User
Wiegand Port 2 26 Bit Unique User
Button Default Settings:
Button 1 Wiegand Port 1
Button 2 Wiegand Port 1
Button 3 Wiegand Port 1
Button 4 Wiegand Port 1 + Relay
Button 5 ~ 10 None
4.2 Default Operation
The RF-RCVR is pre-programmed to work with most access control systems out of the box. The Factory
defaults will provide the following functionality:
All ICT Transmitter signals received will be passed through Wiegand Port 1, with the same Site Code and a
unique User Code for each button. The Relay will also activate for 2 seconds when button 4is pressed.
To immediately use this functionality:
Connect Wiegand Port 1 as shown in Figure 1.
Optionally, connect the Relay NO to a digital zone input and the Relay CM to your system's zone common,
for use as a panic/pendant alarm on Button 4.
Each button will now pass a standard 26 Bit Wiegand code to your access control system for each button
press. Use these to control your doors or other functions.
8Wireless 433MHz Receiver | Installation Manual
4.3 Custom Operation Setup
To customize the operation of an RF-RCVR unit to match your requirements:
Connect a terminal program such as HyperTerminal with the RS232 settings shown under System Default
Settings in this document.
Press ESC to display the main programming menu.
Wireless 433MHz Receiver | Installation Manual 9
5 Programming Options
5.1 Mode Programming Menu
Shortcut: Esc , e , Enter
Type 1, Enter to toggle between the following modes:
ICT Pass Through Mode (default mode)
All ICT Transmitter devices will operate.
Custom Site Code Mode
All ICT Transmitter devices will operate with a fixed site code that is programmable in the Site Code
Programming Menu.
Individual User Mode
Only programmed transmitters accepted.
When Site Code or Individual User mode is selected, an extra option will appear at the main menu for modifying
the site code or user details.
5.2 Quick User Programming
Only available when unit is in Individual User Mode.
To add new remotes when Individual User mode is selected:
Hold down the PRG button (on the bottom right hand side of the unit)
Press any button on the new RF-REM4 or 2, and check the RF light flashes when doing so.
The user has now been added at the next available slot in the user list.
5.3 User Programming Menu
Only available when unit is in Individual User Mode.
Shortcut: Esc , f , Enter
The RF-RCVR will store up to 600 individual Transmitter ID numbers for standalone use.
10 Wireless 433MHz Receiver | Installation Manual
To Add/Modify a User:
Type 1then Enter to edit a user
Type the user number then Enter
Either press any button on the transmitter for this user, or type in the transmitter ID if known. To clear an
entry, type 0, Enter as the TX code.
The menu will automatically prompt for the next user code, enter it as above or press Esc to finish user
programming.
The module will not display previously programmed numbers, it is recommended to make a record of
these when programming.
The RF-RCVR also has a Range Mode which allows for transmitter IDs within a specified range to be accepted
when enabled under standalone use.
To Toggle Range Mode State:
Type 2then Enter to toggle the state of Range Mode.
When Range Mode is enabled, the message Range Mode: On will appear at the top of the User Menu.
By default, Range Mode is disabled.
To Set the Start User:
Type 1then Enter to edit a user.
Type 1 then Enter to select User 1.
Either press any button on the transmitter for this user, or type in the transmitter ID if known. To clear an
entry, type 0, Enter as the TX code.
To Set the End User:
Type 1then Enter to edit a user.
Type 2 then Enter to select User 2.
Either press any button on the transmitter for this user, or type in the transmitter ID if known. To clear an
entry, type 0, Enter as the TX code.
5.4 Site Code Programming Menu
Only available in Custom Site Code Mode
Shortcut: Esc , f , Enter
The RF-RCVR in this mode will accept all RF-REM4 devices with the programmed site code.
To Add/Modify Site Code:
Type 1then Enter to edit the site code
Type the new site code then press Enter
Press Esc to finish programming.
Table des matières
