ICONNECT PRL-60-240 Manuel utilisateur

INSTALLATION INSTRUCTIONS

Thank you for buying iConnect products.

The PRL is the latest technology in projector lifts.

Please read this manual carefully before assembling.

PROJECTOR LIFT

PRL-60-240

CONTENTS

MAIN

CONTENTS

SAFETY

OVERVIEW

LIFT PREPARATION

LIFT INSTALLATION

FINISHING THE CEILING LIFT

ADJUSTMENTS

FINISH

DIMENSION

TECHNICAL SPECIFICATION

iCONNECT

5-6.

7-10.

11-12 / 16-17.

13-15.

18.

19.

20.

Projector lift PRL-60-240 must be installed by specialized personnel only.

Before installing the projector lift, please read the following instructions carefully

1. The projector lift must be used indoors only.

2. It is forbidden to stay under the lift.

3. never connect more than one lift motor to the same switch.

4. In case of maintenance, unplug the power supply.

5. Incorrect use, including exceeding the maximum lifting weight, would be dangerous and invalidate the

warranty.

6. The manufacture do not take responsibility for any damage to property or personal injury, if the lift is used

out side of recommended speciﬁcations.

7. Incorrect servicing could lead to risk of electric shock.

8. For any repairing, please contact directly the dealer you purchased the unit from.

9. Check at least once a year that the screws of the steel cables are well tightened

iCONNECT

SAFETY

iCONNECT

Projector

Motor

Projector Mount

Adjustable Mount Plate

Linkage

Pulley

Lift Frame

Limit Switch

Lift Frame

OVERVIEW

Remove Adjustable Mount Plate

Remove the 8 screws

iCONNECTLIFT PREPARATION

LIFT PREPARATION

Open a hole in the ceiling

600mm

iCONNECT

Mark and drill 4 holes in the ceiling with a diameter of 10 mm

The direction of the screen

iCONNECTLIFT INSTALLATION

Tighten bolts through the holes designated lift and strong

Make sure you locked well

iCONNECTLIFT INSTALLATION

Use a power cable that came with the package. plug the male and female side motor

Connect the other end of the cable to a power source 110 V

Press the switch and lower the lift down

iCONNECTLIFT INSTALLATION

Unplug the projector arm by opening the screw at the top

iCONNECTLIFT INSTALLATION

Table des matières

Autres manuels iCONNECT Système de levage

iCONNECT

iCONNECT TVL-RH Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur

iCONNECT PRL-60-240 Manuel utilisateur

Manuels Système de levage populaires d'autres marques