Icom V10MR Mode d'emploi
1
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
V10MR User Programming Guide
Your new V10MR, in its default state, works correctly with other new (no programming changes) V10MR
radios. Please refer to your instruction manual for basic steps to operate the radio with no
programming changes.
Should you want to change channel assignments, tones, or special features, your V10MR radio has a
number of advanced radio features that can be enabled through its software (CS-V10MR).
To program the radios, you will need the following:
•CS-V10MR Cloning Software. Available for free download on the Icom America website
(Products >Landmobile >V10MR).
•OPC 478UC Cloning Cable (“B” version only). Available from an Icom America Landmobile Dealer
in your area.
•PC running Windows 10 operating system. Note: Apple and Android software is not available.
Default Channels/Frequencies andTone
Channel
Frequency
Bandwidth
CTCSS tone
1
151.820MHz
Narrow
67Hz
2
151.880MHz
Narrow
67Hz
3
151.940MHz
Narrow
67Hz
4
154.570MHz
Wide
67Hz
5
154.600MHz
Wide
67Hz
CS-V10MR Software Modes
The CS-V10MR software has two modes, Simple and Full.
Simple Programming Mode: Allows adding duplicates of the 5 MURS frequencies for the purpose of
using different CTCSS or DTCS tones.
Full Programming Mode: Allows adding duplicates of the 5 MURS frequencies and the addition of a
larger suite of features.
Note: Incorrect Settings in the Full Programming Mode can cause incorrect operation of the radio. Icom
suggests these features be programmed by an Icom dealer only.
2
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
Selecting Simple or Full Mode
1. Open the CS-V10MR software.
2. Click Mode, then select Simple or Full.
Programming in Simple Mode
Memory Channel programming is shown below.
1 Inh
Do not use. For use in radios with Displays only.
2 Frequency (MHz)
Contains the 5 MURS frequencies. Only these frequencies can be entered in
the 16 channel slots. Extra Channel slots are provided if you need to duplicate
frequencies using different CTCSS or DTCS tones.
3 C. Tone
This shows the CTCSS or DTCS tone.
You can program tones for each channel in both simple and full modes. On any
given channel/frequency, radios must have matching tones if they are to
decode each other’s audio.
4 Text
Do not use-For use in other model radios with Displays only.
5 Compander
The Compander compresses the signal to reduce background noise. If this
setting is enabled, all radios must have it enabled for it to work properly on
that channel. This feature may not work effectively with non-Icom radios.
6 PWR Save
This feature saves power by allowing the radio to go into a partial sleep mode
during times when there is no RX or TX traffic.
3
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
Channel Squelch
In Simple Mode, the Squelch setting can only be changed using the push buttons as described in the
Operating Guide.
Programming in Full Mode
The full suite of features is available in Full Mode.
Memory Channel Programming
See instructions for Simple Mode-Memory Channel Programming
Channel Squelch
The squelch setting allows you to adjust the sensitivity of your radio’s receiver.
In Full Mode, the squelch setting can be changed in 2 different ways:
•Using the buttons on the radio, by default. Please refer to your instruction guide for steps.
•Using the programming software in Full Mode, using the Common > Set Mode window.
1. Go to Common > Set Mode.
2. Click SQL Level and select the desired number. Note: A setting of 2is optimal.
Scan Programming
Assumptions:
•Software is in Full Mode
•SQL Level is set correctly
•Frequencies and sub-audible tones have been programmed in and tested for correct
communication.
Note: For complete descriptions of these settings, please refer to the Help files in the programming
software.
1. Scan Settings screen- Set Power-On Scan to one of the following choices:
•Off- User will have to press the Scan Start/Stop button to start a scan after power up.
4
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
•Resume- Upon Power Up, the radio resumes scan if the radio was scanning when the
power was turned off.
•On- Radio begins scanning upon Power Up.
2. Scan List screen. Select Normal Scan. It scans, in sequence, all selected channels in a “round
robin” fashion, starting with the channel set on your rotary knob.
3. In TX CH, select the channel you would normally transmit on while in scan, or when scan is
paused. In this example it is set to Last Ch.
•TX Action setting either cancels scan or allows scan to resume automatically. Ifset to
Cancel Scan, restarting requires pushing the Scan Start/Stop button (see To Start a Scan
following) If set to Pause Scan, scan resumes after the resume timer (Scan Setting screen)
has expired.
4. In CancelChannel, set the channel that you will return to when scan is cancelled using the Scan
Start/Stop button, assigned in the Key and Display screen as described below.
5
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
5. Go to the Common folder and select Key & Display.
6. Set a programmable key to Scan Start/Stop. The following example uses the lower side key.
To start a scan:
1. Switch on the radio power.
2. Press momentarily (do not hold) the Scan Start/Stop key once to start or stop scan. The
radio LED will blink green while actively scanning.
MDC Signaling
MDC contains signals that enable specific functions, such as PTT ID and Radio Check. It is not used unless
these radios are used in conjunction with a higher-tiered radio with a display and the applicable
functions already programmed.
Assumptions:
•Software is in Full Mode
•Squelch is set
•Any tones are set
•All participating radios are also programmed for MDC emergency functions.
PTT ID
PTT ID allows your V10MR radio to send its own ID to another radio that has a display. Note: Icom does
not make MURS radios with displays.
1. Go to Memory Ch.
2. Click MDC and select System 1.
6
Knowledge Base |
©2021 Icom America Inc. The Icom log o is a reg istered tr ademark of Icom Inc.
3. Go to MDC > System > General.
4. In SystemSettings, set MDC On to ON.
5. Set the Self ID to the ID of this radio.
6. Go to PTTID.
7. Set Tx and PTTID Down to Enable.
Once programmed, PTT ID will automatically be sent every time the PTT button is pressed.
Emergency
Emergency signals are only applicable when adding these radios to an existing system with an
Emergency Dispatch decoder. Please see your Emergency system administrator for details on how your
Emergency settings should be programmed. Icom makes no MURS-rated radios with this feature.
2-Tone Signaling
2-Tone Signaling and Muting is used only in specialized systems such as those in Fire Departments. If this
radio is approved to operate on such a system, please contact the administrator for the programming
parametersfor that system.
Table des matières
Autres manuels Icom Radio
Icom
Icom IC-F3160 SERIES Manuel
Icom
Icom IC-2720H Manuel utilisateur
Icom
Icom IC-706MKIIG Manuel utilisateur
Icom
Icom M302 Manuel d'instructions
Icom
Icom IP501H Manuel utilisateur
Icom
Icom IC-F1010 Manuel utilisateur
Icom
Icom IC-F14 Instructions d'installation et d'utilisation
Icom
Icom F3161 Series Mode d'emploi
Icom
Icom IC-R71A Manuel utilisateur
Icom
Icom iF610 Manuel utilisateur
Icom
Icom IP501H Manuel utilisateur
Icom
Icom Two-Way Radios Mode d’emploi
Icom
Icom IC-910H Manuel utilisateur
Icom
Icom IC-SAT100M Manuel utilisateur
Icom
Icom F3021 Manuel du propriétaire
Icom
Icom IC-2200H Manuel utilisateur
Icom
Icom IC-PCR1000 Manuel utilisateur
Icom
Icom IC-2720 Fiche d'information produit
Icom
Icom 9000 F70 Series Guide d'installation
Icom
Icom IC-F43TR Manuel utilisateur
