8ICE i28BTL+ / i28BTL+-CY / i32BTL+
OPERATOR MANUAL
FILLING THE SOLUTION TANK
The machine is equipped with a hose ll-port
(Machine components, item #7) at the rear of
the machine, and a bucket ll-port (Machine
components, item #26)located under the recovery
tank. Before accessing the bucket ll-port make
sure that the recovery tank is empty.
Fill the solution tank to the "100L" level on the
solution tank sight gauge. When using the bucket
ll-port, stop lling when the level reaches the
bottom edge of the ll-port.
Convertional scrubbing - Fill solution tank
with water (not to exceed 60°C/140°F. Pour a
recommended cleaning detergent into the solution
tank according to mixing instructions on the
container)
NOTE: When lling the solution tank with a bucket,
make sure that the bucket is clean. Do not use the
same bucket for lling and draining the machine.
WARNING: Do not put any ammable
materials into solution tank. this can cause an
explosion or a re. Only use recommended
cleaning chemicals. Contact your janitorial
supply distributor for recommendations on
proper chemicals.
WARNING: Do not operate machine
unless you have read and understand this
manual.
1. Swipping the ID card (Machine components, item
#18) to turn on the machine.
2. Check the LED display screen (Panel
components, item #4), if there are fault condes
(Panel components, item #18) and the Fault
indicator (Panel components, item #1) in blink,
please DO NOT operate the machine unless the
faults have been eliminated (please see FAULT
CODES AND ELIMINATE section).
3. Turn on the 1-Step scrub head up/down
button, the scrub head will be lowered down
automatically.
4. Lower squeegee assembly to the oor by
lowering the Squeegee lift lever.
5. Check the solution ow indicator (Panel
components, item #9), press the Solution ow
adjusting button (Panel components, item #10) to
get a desired solution ow.
NOTE: Solution will not begin to ow until the
control handle bail is pulled.
6. Turn on the Vacuum motor switch(Panel
components, item #8).
7. Pull the Control handle bail (machine
components, item #17) backwards to start
scrubbing .The machine will automatically propel
forward. To reverse the machine, simply push
the control handle bail forward.
NOTE: Raise squeegee when reversing machine.
8. The scrubbing speed can be adjusted, press
the Speed increase/ decrease button (Panel
components, item #14, #16) to a desired speed.
NOTE: 45-60 meters (150-200 ft)per minute is
the recommended scrubbing speed.
9. The brush pressure can be adjusted, press the
Brush pressure increase/ decrease button
(Panel components, item #3,#6) to get a
desired brush pressure.
10. To stop scrubbing, release the control handle
bail, turn o the 1-Step scrub head up/down
button to raise he scrub head assembly, raise
the squeegee assembly.
WARNING: Fire Or Explosion Hazard. Do
Not Pick Up Flammable Materials Or Reactive
Metals.
1. Go slow on inclines and slippery surfaces. Do not
operate the machine on inclines that exceed 5%
(3°).
2. Do not keep the machine in the same position with
pad / brush spinning, keep the machine moving to
prevent damage to oor nish.
3. If the squeegee assembly leaves streaks on the
oor, raise the squeegee o the oor and wipe the
blades down with a damp cloth. Pre-sweep the
area to prevent leaving streaks on the oor.
4. Pour a recommended defoamer into the recovery
tank if excessive foam appears.
WARNING: Do not allow foam to enter the
oat shut-o screen, vacuum motor damage will
result. Foam will not activate the oat shut-o
screen.
5. Occasionally check the battery meter(Panel
components, item #2). when the battery is very
low, stop scrubbing and recharge the batteries.
WARNING: When battery meter is in the
red, do not continue to operate the machine.
Battery damage may result.
MACHINE OPERATION
WHILE OPERATING MACHINE
