iCanTek iCanView220 Manuel utilisateur
iCanView220/220W
User’s Guide
Rev1.0(Aug. 2006)
iCanView220/220W
User’s Guide
Use only the power adapter supplied with the iCanView220/220W. Use of
third party power supplies will void the factor warranty.
Some Cities, States, Provinces, Local and Federal Governments have laws
regulating the use of surveillance equipment. Make sure to understand
all local laws.
This Camera Uses Microsoft ActiveX
Do this first!
Before attempting to connect and view video from the iCanView220/220W,
install i-NVR on the PC. Greatly simplifying the ActiveX installation process, iNVR will
automatically install the ActiveX component needed for a direct connection with IE
Explorer! For more detailed information on using “i-NVR” see the i-NVR User Guide.
iCanView220 series network cameras are designed for indoor use only.
When using iCanView220 outdoors, or in an environment that exceeds
specifications, use an additional outdoor rated, water-resistant housing.
The iCanview 220 is not a vandal resistant product, thus use care to avoid
physical damage. With safety in mind, keep out of children’s reach.
Disassembly, or modifications void the factory warranty.
Read this First
Rev1.0(Aug. 2006)
iCanView220/220W
User’s Guide
Technical Advisory Note:
Do not apply power through the power input jack on the back of the camera
when power is supplied through a LAN cable using proprietary PoE.
This will damage the camera!
This will void the warranty. iCanTek assumes no responsibility for
damages caused by applying power simultaneously from both
connections.
(SIMULTANEUOSLY APPLYING POWER, USING BOTH
POE AND THE DIRECT POWER SUPPLY INPUT JACK ON
THE BACK OF THE CAMERA, DAMAGES THE CAMERA!)
WARNING
POE/POWER OVER ETHERNET WARNING
iCanTek devices do not support standard POE.
Connecting this device to a standard PoE device will
damage the device and void the warranty.
DUAL POWER DAMAGES THE CAMERA!
DO NOT APPLY DUAL POWER SIMULTANEOUSLY!
WARNING
POE/POWER OVER ETHERNET WARNING
Rev1.0(Aug. 2006)
iCanView220/220W User’s Guide
FCC
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio, or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try correcting the interference by one, or more of the following
methods:
zReorient, or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment to and outlet on a different circuit than that of the
receiver device
zConsult a dealer, or experienced radio/TV technician for help.
This appliance and its antenna must not be co-located, or operating in conjunction with
any other antenna or transmitter. A minimum separation distance of 20 cm must be
maintained between the antenna and the user in order to meet RF exposure requirements.
Any changes, or modifications to the construction of this device, which are not explicitly
approved by the party responsible for compliance, may void the user’s authority to operate
the equipment.
FCC, CE Warning
Revision History
Date Rev No Description
2006-08-14 0.9 Creation of the document
2006-09-16 1.0 Wireless LAN updates & Camera module updates.
Rev.1.0 (Aug. 2006) 4
iCanView220/220W User’s Guide
Table of Contents
1. Introduction............................................................................................................................................ 6
1.1. Overview.......................................................................................................................... 6
1.2. iCanView220/220W Features........................................................................................ 7
1.3. iCanView220/220W Applications.................................................................................. 7
2. Product Description ...............................................................................................................................8
2.1. Contents .......................................................................................................................... 8
2.2. Preview ............................................................................................................................ 8
2.3. Physical description........................................................................................................ 9
2.4. PC Requirements .......................................................................................................... 13
2.5 Quick Installation Guide................................................................................................ 14
3. Connecting iCanView220/220W to Network..................................................................................... 18
3.1. Connecting to LAN........................................................................................................ 18
3.2. Connecting to an xDSL/Cable Modem....................................................................... 19
4. IP-Installer............................................................................................................................................ 20
4.1. IP-Installer Main Window ............................................................................................ 20
5. Configuring iCanView220/220W in Administrative Mode................................................................ 21
5.1. Log On............................................................................................................................ 21
5.2. Basic Setup.................................................................................................................... 23
5.3. Network Configuration................................................................................................. 25
5.4. Wireless Configuration (iCanView220W only).......................................................... 28
5.5. CCD Adjustment (Not applicable for iCanView220/220W)................................... 30
5.6. User Admin & Time Setup........................................................................................... 32
5.7. Sensor & Capture Setup.............................................................................................. 35
5.8. Alarm Device Setup...................................................................................................... 37
5.9. Motion Region Setup.................................................................................................... 38
5.10. PTZ Setup(This is not related with iCanView220/220W Network Camera) ....... 40
5.11. Encryption Set up....................................................................................................... 42
5.12. Upgrade & Reset......................................................................................................... 44
5.13. Status Report.............................................................................................................. 46
6. Tips for Using iCanView220/220W .................................................................................................... 47
6.1. Sensor-IN and Relay-OUT ........................................................................................... 47
6.2. Trouble Shooting........................................................................................................... 50
6.3. Web Viewer.................................................................................................................... 52
6.4. How To Upgrade Your iCanView220/220W System ................................................. 54
Rev.1.0 (Aug. 2006) 5
iCanView220/220W User’s Guide
1. Introduction
1.1. Overview
The iCanView220/220W is a state-of-the-art network camera which transmits synchronized video
and audio data in real time at D1 resolution and at full frame rates. Depending on which model
you purchased the iCanView220/220W is offered with either a standard Ethernet interface (220), or
an embedded WiFi transciever(220W).
Using MPEG4 CODEC technology, the 220/220W delivers high quality video via highly compressed
data streams. Using TCP/IP based connections from remote locations, the iCanView220/220W
may be monitored and/or controlled via the internet, or intranet. Unlike analog CCTV equipment,
or DVRs, the iCanView220/220W is easy to install. Often one can often take advantage of existing
network infrastructure saving valuable installation labor and equipment costs. Based on iCanTek’s
Embedded Software Solution (Embedded Web Server, Embedded Streaming Server & Network
Protocol), the iCanView 220/220W delivers unprecedented performance and stability. Weather
your application is basic, or scaling to the enterprise, iCanTek Network Video Recording Applications
(iNVR & NVRPRO) offer highly reliable methods of managing your security video.
Rev.1.0 (Aug. 2006) 6
iCanView220/220W User’s Guide
1.2. iCanView220/220W Features
y1 channel synchronized real time Video/Full Duplex Audio streaming
MPEG-4 video, ADPCM audio.
yBi-directional audio communication
Real time audio communication between iCanView220/220W and Client PC(s)
yThe viewer assisted recording and playback functions.
y1 Alarm sensor input/1 relay output
yMotion detection
– Up to 3 independent motion detection zones, featuring arbitrary shape configuration.
- E-mail, or FTP Full Motion Video Clips on motion detection alarm
- Optional Motion Detection Only Based Recording
yResolution
- NTSC : 704x480, 352x240, 176x144.
- PAL/SECAM : 704x576, 352x288, 176x144
yRS-485 interface for Pan/Tilt device connection
yRemote Administration and Control
Entire operational parameter set up, Software upgrade
yEmbedded WiFi interface (iCanVeiw220W only) – IEEE 802.11b/g
yProprietary PoE (Power over Ethernet) for installation convenience.
1.3. iCanView220/220W Applications
ySecurity surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government
facilities, military, etc.,
yReal time Internet broadcasting
yRemote monitoring (hospitals, kindergartens, traffic, public areas, etc.,)
yTeleconference (Bi-directional audio conference)
yDistance (Remote) Learning/Education
yWeather and environmental observation
Rev.1.0 (Aug. 2006) 7
iCanView220/220W User’s Guide
2. Product Description
2.1. Contents
Each Camera ships with the following equipment:
Components Description Remarks
iCanView220/220W iCanView220/220
Network Camera/Server
Power adapter Input : 100~250V 50-60Hz
Output : 7 ~23V, 8W Standard Power
AC power cable AC 250V, 10A~16A
RCA Video cable Cable for analog video output from
camera module inside of network
camera
Use your hand held
video monitor for easy
camera field of view
setup.
CD-ROM Software & User’s Guide
Quick Reference Guide
Quick installation guide Will be provided
2.2. Preview
iCanView220/220W IP-Installer i-NVR
1CH MPEG-4 Network
Camera
PC software to assign an IP
address to the
iCanView220/220W
PC software to view and record
streaming A/V data transmitted
from the iCanView220/220W
Rev.1.0 (Aug. 2006) 8
iCanView220/220W User’s Guide
2.3. Physical description
2.3.1. Configuration DIP Switches
Depending on which model you purchased, the iCanView220/220W comes with one of three
optional modules described in the following table.
Camera module Lenz Misc.
270K pixel Fixed lenz PAL/NTSC
410K pixel Varifocal lenz PAL/NTSC
Day & Night Varifocal lenz with IR cut filter PAL/NTSC
Figure 2-1 illustrates exterior view and internal parts. Accommodating various camera site
requirements, the camera module can be configured to enable/disable various video features.
Figure 2-1. External and inner views of CanView220/220W
Rev.1.0 (Aug. 2006) 9
iCanView220/220W User’s Guide
2.3.2. Bottom view and Cable Harness
Sensor in / relay out
DC power
MIC/Line IN
Line Out
100BaseT(RJ45)
Figure 2-2. Rear Views and iCanView220/220W Cable
yMIC. /LINE In : Connect external audio source or microphones here.
Use a standard stereo earphone jack for the connections.
Audio In
Ground
Not used
Audio In
Ground
Not used
Audio out
Ground
Not used
Audio out
Ground
Not used
Rev.1.0 (Aug. 2006) 10
Autres manuels pour iCanView220
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels iCanTek Caméra de sécurité
iCanTek
iCanTek iCanView 240 Manuel utilisateur
iCanTek
iCanTek iCanView 110 Manuel utilisateur
iCanTek
iCanTek iCanView220 Manuel utilisateur
iCanTek
iCanTek iCanView372 Manuel utilisateur
iCanTek
iCanTek iCanView232 Manuel utilisateur
iCanTek
iCanTek iCanView290PT Manuel utilisateur
iCanTek
iCanTek iCanView270 Manuel utilisateur
iCanTek
iCanTek iCanView 222 Manuel utilisateur
iCanTek
iCanTek iCanView 230 Manuel utilisateur
