IAdea XDS-1070 Manuel utilisateur
XDS-1070/1078
This printed quick guide provides a quick walkthrough of the set up process.
For complete documentation, please visit www.digisignage.com
Box Contents
Port connections
Front View
Rear View
Quick Start Guide
Main Unit
AC Adapter
(with select power plug)
Table Stand
Power and micro SD
card brackets
IAD_DGS_X7S_20EP
Mounting and Installation
Mounting Option 1: [VESA mount]
Supporting VESA standard: VESA MIS-D75 (75*75mm)
Supporting screw: M4*4mm (exclude the mounting plate thickness)
Mounting Option 2: [Using back cover]
(power / SD card brackets MUST NOT be installed while mount on back cover)
Release the back
cover screw to
release back cover
Install back cover :
thread head height
not to exceed 3mm
Route power and network cable from
bottom, connect to signboard before
mounting signboard on back cover
Insert power plug
Fasten bracket
onto the socket
Insert SD Card
bracket
Fasten the SD
Card bracket
Landscape
Simply screw the supplied table
stand onto the stand screw hole.
Support landscape/portrait setup.
Portrait
Securing power/network cable
Installing the table stand
Mounting options
Securing SD Card
System setup
1INSTALL the AC power adapter
→You should see the player boot up screen as
shown in right.
2WAIT while player boots up
→Once you see “Basic settings” on screen, the
unit is ready for content update or menu
configuration.
3PLUG IN a USB mouse to the unit’s USB port or configure by touch
screen (XDS-1078 only).
4Enter the corresponding configuration option by moving the mouse
cursor over the configuration and click on the option to enter (or tap
on the configuration option for XDS-1078)
→Find and set the correct time/date AND time zone.
IMPORTANT: time zone must be set correctly in the menu or via
management software for scheduled playback
→(OPTIONAL) Set a Password in the menus to prevent unauthorized
changes.
IMPORTANT: Password will be asked for when entering the setup
menu during playback.
5Click Set content button to configure your signage appliance to the
content service if needed
→For advanced player configuration, such as static IP, display
resolution, and firmware update, visit www.digisignage.com for more
information
IAD_DGS_X7S_20EP
Content Management
Please consult the software documentation for information specific to your
management solution.
Image Retention Disclaimer
When an image is displayed on-screen for prolonged periods of time, you may
see a faint image after it is replaced. This is expected normal behavior for
displays.
Image retention may be reduced by:
Avoiding still images shown on-screen for more than a few minutes
Using non-contrasting colors and brightness
Using background colors other than gray
Troubleshooting
How do I interrupt playback and enter setup menu?
You can move your mouse cursor to the corner of the screen, press and hold
the left key for 10 seconds to exit playback and enter setup menu.
Some videos playback jumpy or incorrectly, How do I get the best video playback
performance?
We provide a video convert tool with a pre-configured profile for users to
encode video to get best video playback performance.
Visit www.digisignage.com to download video convert tool.
Reset player to factory defaults (AC adapter is required)
If modifying settings cause unintended results or if you have forgotten your
password, please reset the player. Local contents will also be removed.
1. Press and hold the reset button with a pen.
2. Use AC adapter, re-connect the power cord while holding reset
button.
3. Wait until the power LED flashes, release reset button and wait for
system to initialize to factory default state.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels IAdea Écran tactile
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
