i3 International Ax51B Manuel utilisateur
Ax51B IR Bullet Camera
User Guide
Before attempting to connect or operate this product, read these instructions carefully.
Save this manual for future use.
CONTENTS
1. Warnings and operation notes..........................................3
2. Product Overview ............................................................4
3. Unpacking....................................................................5
4. Installation.....................................................................6
5.
Connecting your IP Camera to the SRX-Pro Server.......
...7
6. Advanced Camera Setup..................................................15
7. Specifications.................................................................28
2
i3-TRNG-CAMS-Ax51B.indd Rev. 130411
Ax51B IR Bullet Camera User Guide
COPYRIGHT ©2013 by i3 International, Inc. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including but not limited to, photocopying,
recording, or by any information storage or retrieval system, without the prior
written permission of the copyright owner and the publisher.
Annexxus is a registered trademark of i3 International Inc.
Disclaimer
This user guide is provided as is, without warranty of any kind, expressed or
implied, including but not limited to performance, merchantability, or fitness for any
particular purpose. Neither i3 International Inc. nor its dealers or distributors shall be
liable to any person or entity with respect to any liability, loss, or damage, caused or
alleged to have been caused directly or indirectly by this information.
Furthermore, i3 International Inc. reserves the right to revise this publication, and to
make changes to the content at any time, without notice.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Address:
i3 International Inc.
780 Birchmount Road, Unit 16
Scarborough, ON M1K 5H4
Canada
Contact us:
Tech Support: 1.877.877.7241
Web Site: www.i3international.com
Table of Contents
1. Warnings and operation notes
2. Product Overview
3. Unpacking
4. Installation
5. Configuration
6. Advanced Camera Setup
7. Specifications
3Rev. 130411i3-TRNG-CAMS-Ax51B.indd
1. Warnings and operation notes
Thank you for purchasing i3 Ax51B IR Fixed Bullet camera.
Please read this guide carefully before you install the camera. Keep this
guide for future reference.
Ax51B comes with a fixed lens and a built-in heater. 24 high quality IR illuminators
built around the lens facilitate crystal clear pictures with no outside illumination as
far as 25 meters (82 ft). Plus, with IP67-rated all-weather waterproof, aluminum
casing, this camera is ideal for outdoor applications such as convenience stores,
streets and parking lots. PoE, DC12V and AC24V power is supported in the indoor
installations, where the heater is not required. Use DC24V/AC24V power for outdoor
installations only to supply enough power to the built-in heater.
If the system needs to be modified or repaired, contact a certified i3 International
Dealer/Installer. When serviced by an unauthorized technician, the system
warranty will be voided. Should you have any problems or questions regarding our
products, contact your local i3 International Dealer/Installer.
1.1 Precautions
Installation and serving should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain
your warranty.
When installing your Ax51B camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -40° Celsius or -40° Fahrenheit and above 50° Celsius or
122° Fahrenheit.
4
i3-TRNG-CAMS-Ax51B.indd Rev. 130411
1.2 Power Supply
Ensure the supplied voltage meets the power consumption requirements of this
camera before powering the camera on. Incorrect voltage may cause irreparable
damage to the video camera and will effectively void the camera warranty.
PoE, DC12V and AC24V power is supported in the indoor installations, where the
heater is not required. Use DC24V/AC24V power for outdoor installations only to
supply enough power to the built-in heater.
1.3 Cleaning
• For maximum optical clarity, the camera or lens must remain clean. Use a soft,
dry cloth to remove finger prints and dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened
with a small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finish.
1.4 Servicing
To avoid electrical shock and to preserve the product warranty, DO NOT
disassembles the camera. Refer servicing to qualified personnel only.
2. Product Overview
• High Definition Images
Clear and detailed HD quality images in all conditions. Unlike other megapixel
cameras, Ax51B-series offer higher resolutions and better frame rates. Blurry
images are reduced and individuals and objects of interest come with perfect
clarity.
WARNING! The use of CSA certified/ UL Listed Class 2 power
adapter is required to ensure compliance.
WARNING! To reduce the risk of fire or electric shock, do not
expose the product to rain or moisture.
5Rev. 130411i3-TRNG-CAMS-Ax51B.indd
3. Unpacking
Ensure that the items received match those listed on the order form and packing slip.
The dome camera packing box includes, in addition to this manual:
1. Flat Head Screw (Tapping Type) x3
2. Plastic Anchor x3
3. RJ-45 Female / Female Coupler
4. Mounting Pack-in Bracket
5. Guide Pattern Sticker x1
6. Printed Quick Start Guide x1
7. CD (User Manual, Annexxus Finder, Quick Start Guide) x1
8. Fully Assembled Network Bullet IR Camera x1
If any parts are missing or damaged, contact the dealer you purchased the camera
from.
12
3
45
Guide Pattern
Note: Mounting surface material
determines screw type.
• Triple Streaming
The Ax51B-series Network Camera is designed to show extreme image detail.
H.264/MPEG4/MJPEG triple streaming allows you to choose the appropriate
code for your bandwidth.
• Cost-saving H.264 Support
The AX51B-series support the H.264 compression standard. H.264 greatly
reduces the size of video without compromising image quality. Storage and
bandwidth are reduced.
6
i3-TRNG-CAMS-Ax51B.indd Rev. 130411
4. Installation
Use the provided bracket and equipment to mount the camera. After installation,
your network camera should be accessed from your local network. See Section 5:
Connecting your IP Camera to SRX-Pro Server.
4.1 Dimensions
4.2. Camera Parts and Definitions
A. Power In: (Red+/Black-): power connector.
Use DC12V/AC24V for indoor applications, use DC24V/AC24V for outdoor ap-
plications to supply enough power to the built-in heater.
B. RJ-45 Ethernet Connector: network connection.
Supports PoE (Power over Ethernet) cable for indoor applications. PoE power
will not work when the camera is installed outdoors where the use of heater is
required for camera operations.
Note: If PoE (Power over Ethernet) connector is used, an electrical cable is not
required
C. BNC: video output
A. Power In
(Red+/Black-)
B. RJ-45 Ethernet
Connector
C. BNC
7Rev. 130411i3-TRNG-CAMS-Ax51B.indd
4.3 Wall/Ceiling Mount Installation / Adjusting Camera Position
1. Adhere the “Guide Pattern Sticker” to the desired location on the mounting
surface and mark hole positions.
2. Drill 3 mounting holes on the mounting surface according to the guide sticker.
3. For cement surfaces, insert the Plastic Anchors into the holes. For softer sur-
faces, do not use the Plastic anchors.
4. Secure the mounting bracket to the surface using the provided screws.
Tapping
Type
Screws
Plastic
Anchors
Plastic
Anchors
Tapping
Type
Screws
To adjust the view
angle, loosen the knob
to rotate the bracket.
5. Connecting your IP Camera to the SRX-Pro Server
5.1 Camera Connection Options
i3 SRX-Pro Server
Crossover direct connection
LAN
i3 SRX-Pro Server
Via Gigabit Switch
Connection Type 1:
Connection Type 2:
8
i3-TRNG-CAMS-Ax51B.indd Rev. 130411
5.2 Hardware/Software Requirements
The following requirements must be met to achieve a successful network connection
with the Ax51B IR Bullet IP camera.
SRX-Pro Server:
• i3 SRX-Pro Version 3.0 or higher
• Latest GiPi adapter is installed. GiPi adapters can be downloaded from i3 FTP
website. (Please contact i3 Technical Support for more information.)
• Windows XP, XPe or 7 Pro or 7e
• Internet Explorer Version 6.0 or later
• CPU: Intel Pentium Core 2 or higher
• Memory: 1GB or more
• VGA card--supporting Direct X 9.0 or above
Power Supply
PoE, DC12V and AC24V power is supported in the indoor installations, where the
heater is not required. Use DC24V/AC24V power for outdoor installations only to
supply enough power to the built-in heater.
Note: Camera damages resulted from improper power application are
NOT covered by the camera warranty.
Switch
A Gigabit Switch is required to monitor two or more cameras from the same
SRX-Pro Server.
5.3 Using Annexxus Finder to assign IP Address to your IP Camera
To connect your Annexxus camera to your SRX-Pro Server, follow these instructions:
9Rev. 130411i3-TRNG-CAMS-Ax51B.indd
1. Close SRX-Pro Server software by pressing Alt+Shift+Ctrl+F4.
2. Change the IP address on the onboard NIC (LAN) (or on NIC1 if your SRX-Pro
Server has two onboard NIC cards) of your SRX-Pro Server to 192.0.0.XXX to
match the default IP range of your Annexxus IP camera.
3. Connect the network cable from the SRX-Pro Server (crossover direct
connection) or from the Gigabit switch to your Annexxus camera.
4. Turn on your Annexxus camera.
5. Locate the CD that came with your Annexxus camera and insert it in the
CD-ROM drive of your SRX-Pro Server.
6. Double-click “AnnexxusFinder.exe” file to install Annexxus Finder application.
Annexxus Finder application discovers all Annexxus cameras connected to your
network.
7. Follow the Annexxus Finder installation instructions until the application has
been successfully installed on your SRX-Pro Server.
8. Double-click Annexxus Finder icon on the Desktop to launch the application.
The application window will appear displaying a list of active network cameras
9. Next, select desired camera in the Annexxus Finder software by double-clicking
it in the list and click Edit.
10. Enter the new IP address and Subnet Mask of the camera in the Change IP
Camera’s default IP address is 192.0.0.16
Camera’s default subnet mask address is 255.255.255.0.
Default camera User Name: admin and default Password: 1234
10
i3-TRNG-CAMS-Ax51B.indd Rev. 130411
Address area. The new camera IP address must match the original range of
your SRX-Pro LAN or NIC1 card.
E.g. If your original SRX-Pro Server’s IP address was 192.138.10.122, change
your Annexxus camera’s IP address to 192.138.10.XXX.
Remember: Annexxus Cameras cannot share an IP address, each camera
requires its own unique IP address.
11. Enter the default camera password: 1234 in the Input Password field and click
Table des matières
Autres manuels i3 International Caméra de sécurité
i3 International
i3 International Ax47R4 Manuel utilisateur
i3 International
i3 International M79 Manuel utilisateur
i3 International
i3 International Ax45RM series Manuel utilisateur
i3 International
i3 International Ax61 series Manuel utilisateur
i3 International
i3 International Ax40W2 series Manuel utilisateur
i3 International
i3 International Ax45RM series Manuel utilisateur
i3 International
i3 International Ax63Z Series Manuel utilisateur
i3 International
i3 International Ax47R series Manuel utilisateur
i3 International
i3 International Ax78R Manuel utilisateur
i3 International
i3 International Am57 Manuel utilisateur
i3 International
i3 International Ax46-series Manuel utilisateur
i3 International
i3 International Ax52D2MV Manuel utilisateur
i3 International
i3 International Ax32VD14 Manuel utilisateur
i3 International
i3 International i3F417U Manuel utilisateur
i3 International
i3 International Ax63Z Series Manuel utilisateur
i3 International
i3 International Am52R Manuel utilisateur
i3 International
i3 International i3R363 Manuel utilisateur
i3 International
i3 International Ax85 Manuel utilisateur
i3 International
i3 International M75 Manuel utilisateur
i3 International
i3 International Ax47R series Manuel utilisateur
