i-Pix BB4 Manuel utilisateur
4
BB
User Manual
i-PIX
4
BB washlight
contents
INTRO, RIGGING, SET UP & MODES
SAFETY FIRST page 3
THE BB7 page 5
RIGGING page 6
SET UP page 7
MODES page 8
MODES A GRAPHICAL OVERVIEW page 12
OPERATING INSTRUCTIONS
STAND ALONE FUNCTIONS page 13
STORING A DMX INPUT AS A MEMORY page 13
CREATING A MEMORY page 14
RECALLING A MEMORY page 17
CREATING A CHASE page 18
THE TECHNICAL STUFF
TECHNICAL SPECIFICATIONS page 20
TROUBLE SHOOTING page 23
QUICK RESET page 25
APPENDICES
APPENDIX 1 ROHS COMPLIANCE
AND WEEE DIRECTIVE INSTRUCTIONS page 26
APPENDIX 2 SERVICE CONTACT DETAILS page 27
7
BB
BB7 USERS MANUAL - PAGE 2
CELL ORIENTATION page 24
23
26
28
29
30
BB4
BB4
BB2x2
SAFETY FIRST
THE BB4
RIGGING
SET UP
MODES
MODES A GRAPHICAL OVERVIEW
page 3
page 5
page 6
page 7
page 8
page 15
INTRO, RIGGING, SET UP & MODES
contents
STAND ALONE FUNCTIONS
STORING A DMX INPUT AS A MEMORY
CREATING A MEMORY
RECALLING A MEMORY
CREATING A CHASE
page 16
page 16
page 17
page 19
page 21
OPERATING INSTRUCTIONS
THE TECHNICAL STUFF
CELL ORIENTATION
TECHNICAL SPECIFICATIONS
UNIT DIMENSIONS DRAWING
TROUBLE SHOOTING
QUICK RESET
page 23
page 24
page 26
page 27
page 29
APPENDICES
APPENDIX 1 ROHS COMPLIANCE
AND WEE DIRECTIVE INSTRUCTIONS
APPENDIX 2 SERVICE CONTACT DETAILS
page 30
page 31
SAFETY FIRST
The following symbols are used to identify important safety information in this manual:
WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing the BB4
This product is for professional use only. It is not for household
use. This product presents risks of severe injury or death due to fire
hazards, electric shock and falls.
Warning!Class 2M LED product. Do not look into the beam from a
distance of less than 40 cm (16 inches). Do not stare into the beam
for extended periods at a short distance. Do not view the beam
directly with optical instruments.
!Read this manual before installing, powering or servicing the fixture, follow the
safety precautions listed below and observe all warnings in this manual. If you
have questions about how to operate the fixture safely, please contact I-Pix.
Warning!
Safety hazard.
Risk of severe
injury or death
Warning
LED light
emission. Risk
of eye injury
!Warning!
Hazardous
voltage. Risk
of lethal or
severe
electric shock
Warning!
Fire hazard
BB4 USERS MANUAL - PAGE 3
PROTECTION FROM ELECTRIC SHOCK
Shut down power to the entire installation at the building’s main power distribution board and lock
out power (by removing the fuse for example) before carrying out any installation or
maintenance work.
Disconnect the fixture from AC power before removing or installing any cover or part
and when not in use.
Disconnect the fixture from AC power before removing or changing the fuse.
Always ground (earth) the fixture electrically.
Use only a source of AC power that complies with local building and electrical codes and has both
overload and ground-fault (earth-fault) protection.
Connect this fixture to AC power either using the supplied power cable or via 3- conductor cable
that is rated minimum 20 amp, hard usage. Suitable cable types include
ST, SJT, STW, SEO, SEOW and STO.
The voltage and frequency at the power outlet are the same as the voltage and frequency applied
to the power inlet. Only connect devices to the power outlet that accept this voltage & frequency.
Before using the fixture, check that all power distribution equipment and cables are in perfect
condition and rated for the current requirements of all connected devices.
Do not use the fixture if the power cable or power plug are in any way damaged, defective or wet,
or if they show signs of overheating.
PROTECTION FROM FIRE
Do not attempt to bypass thermostatic switches or fuses. Replace defective fuses with ones of
the specified type and rating only.
Provide a minimum clearance of 0.1 m (4 in.) around fans and air vents.
Do not modify the fixture
Apart from I-PIX accessories do not stick filters, masks or other materials directly onto the light.
PROTECTION FROM INJURY
Do not hang fixtures from each other. Use two OMEGA clamps per fixture or I-PIX
SINGLE or DOUBLE YOLKS when suspending.
When suspending the fixture, ensure that the structure and all hardware used can hold at least
10 times the weight of all devices suspended from them.
Use two secondary attachments (such as a safety cable) to secure each fixture.
Secondary attachments must be able to hold at least 10 times the weight of all devices
suspended from them and must be installed as described in this manual.
Check that all external covers and rigging hardware are securely fastened.
Block access below the work area and work from a stable platform whenever installing,
servicing or moving the fixture.
The LED emission presents a hazard to eyesight at a distance of 4 - 40 cm (1.6 -16 inches)
when the eye is exposed to the beam for longer than 0.25 seconds.
Do not look at LEDs from a distance of less than 40 cm (1 ft. 4 in.) without suitable
protective eye wear.
Do not look at LEDs with magnifiers or similar optical instruments that may concentrate the
light output.
BB4 USERS MANUAL - PAGE 4
BB 4 Washlight
BB4 USERS MANUAL - PAGE 5
The BB 4 washlight provides the user with an energy saving high power light. Four powerful light sources gives the
feel and look of a modern light fixture. LED in origin, the appearance from the four blended sources shows no
visible appearance of existing led technology yet has the performance we have all come to understand from this
novel form of light.
The BB 4 washlight, is equipped with four custom Light Engines from Lamina. It's one of the highest power point
source led light available. It is the homogenized source of the three saturate colours that makes our colour mixing
so good.
The performance of these light engines to i-pix's exacting colour specifications gives a tighter tolerance and
improved colour performance, which makes tungsten lighting performance from the BB 4 possible. Daylight
temperatures can also be found with ease and finally a fixture that does not need a nudge from amber to
compensate. The whites are believable and full of low power energy, which makes one wonder if the source is
really an led engine.
The BB 4 has a super smooth control with 16 bit resolution, enhancing the feel of the fixture when wishing to
emulate the tungsten performance you would expect from pre existing fixtures. Different operating modes ensure
ease of use. With consumption of 120 watts, the fixture draws half and amp on full @ 240 volts.
i-PIX
4
BB washlight
BB4 USERS MANUAL - PAGE 6
Rigging a BB4 horizontally
To rig a BB4 horizontally use the OMEGA brackets supplied with the lamp.
These would have your clamp of choice bolted on to them.
The OMEGA brackets can be attached to each end & the middle of the lamp using the camlocs.
First place the camloc pins in the receptacles with the levers facing out
then to secure the brackets give the levers a quarter turn clock wise.
Make absolutely sure all four attachment points are secure BEFORE rigging the light ALWAYS secure the lamp to
the truss, pipe e.t.c. with two safety bonds. One attached to the lamp through the safety point shown in fig 1
the other attached to the yolk through the safety point shown in fig 2 NEVER through or to the brackets.
fig 1 fig 2
WRONG
BB4 USERS MANUAL - PAGE 7
Rigging a BB4 vertically
To rig a BB4 vertically use the SINGLE or DOUBLE YOLK hanging brackets. The brackets can be supplied as
accessories for the lamp. You would obviously have your clamp of choice bolted on to them.
The YOLK brackets can be attached to the top, middle or the lamp using the camlocs.
First place the camloc pins in the receptacles with the
levers facing out the correct way.
Then to secure the brackets turn the levers a quarter
turn clock wise.
BB4 USERS MANUAL - PAGE 8
WRONG
So after a quarter clockwise both levers should
face each other in the centre.
ALWAYS secure the lamp to the truss, pipe e.t.c. with two safety bonds.
One attached to the lamp through the safety point shown in fig 1 the other attached to the
LAMP yolk through the safety point shown in fig 2. NEVER through or to the RIGGING yoke.
fig 1 fig 2
1. Select appropriate dimmer curve
The BB4 offers a choice of two dimmer curves.
1 LINEAR - the output increases directly with dmx input.
2 ENHANCED - the first 10% of the output is controlled over the first 50% of the DMX input.
First press the button under the MORE legend.
Then press the PROFILE button.
Then select the appropriate dimmer curve.
linear LIN.
Or enhanced ENH.
2 Disable or enable user interface backlight
Whilst in PROFILE you may choose to switch off the user
interface backlight. When you press the button above BACK
ON the legend will change to BACK OF and the backlight will
go out 5 seconds after the interface is last used, though the
backlight will come back on whenever any button is pressed.
When you press the button above BACK OF the legend will
change to BACK ON and the backlight will remain lit
constantly.
BACK ON shows the current status
of the backlight
BB4 USERS MANUAL - PAGE 9
SET UP
4INVRT1 ADDR 001
MODE 3 5CH MORE
PRESS
PROFILE CHASE
MAN STORE
PRESS
CURV-LIN BACK ON
PRESS
CURV-ENH BACK ON
PRESS
CURV-LIN BACK ON
PRESS
CURV-LIN BACK OF
PRESS
4INVRT1 ADDR 001
MODE 1 3CH MORE
PRESS
4INVRT1 ADDR 111
MODE 1 3CH MORE
PRESS
100s ADDR 011
10s 1s
PRESS
3 Select appropriate operating mode
The BB4 will gives you a choice of ten operating modes. These modes
will enable you to set up the lamp in the most appropriate way for the
many different jobs the lamp will be used for. The nuts and bolts of the
modes are described in detail in pages 12 to 15.
To select a mode
Keep the button below the MODE legend depressed go
through the modes, just before the one you desire stop,
then press once.
4 Select appropriate DMX address
First press the button above the ADDR legend.
Then change the address using the 100s,10s & 1s buttons.
BB4 USERS MANUAL - PAGE 10
Table des matières
Autres manuels i-Pix Projecteur
Manuels Projecteur populaires d'autres marques
VIZULO
VIZULO Micro Martin Guide de l'utilisateur
EuroLite
EuroLite LED IP FL-100 SMD Manuel utilisateur
Cooper Wheelock
Cooper Wheelock XB12 Manuel utilisateur
Allen + Roth
Allen + Roth 17624-000 Manuel utilisateur
ADJ
ADJ 4 STAGE PAK Manuel utilisateur
Cooper Lighting
Cooper Lighting EGL91SW233 Manuel utilisateur
