i Display i view classic Manuel utilisateur
i View Classic
User Manual
Index
3
3
4
4
5
5
6
7
7
10
10
11
11
13
14
14
15
21
22
23
23LCD Screen Specication
2
Main Supply / Main Unit / Main Adaptor
Main Supply
This equipment is designed to operate from a 100-240 Volt, 50/60Hz AC main
supply. The use of other power sources may damage this equipment. Check that
the voltage marked on the rating plate located at the rear of the power adaptor
states 100-240V. The manufacturer will NOT accept responsibility for damage or
injury caused by connecting to the wrong voltage.
Main Unit
This device complies with CE/FCC regulations.
Main Adaptor
The power adaptor supplied is compatible with a standard main socket. NB. If the
power adaptor or lead gets damaged, it must be replaced by a qualied service
agent with an approved adaptor of the same type and rating.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) This device must accept any interference received,
including interference which may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
Safety and Warnings
3
FCC Radiation Exposure Statement / Warning
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Dangerous voltage constituting a risk of electric shock is present inside this
equipment.
This mark is applied to show the equipment conforms to European safety and
electro-magnetic compatibility standards.
There are important operating and maintenance instructions in the literature
accompanying this equipment.
Warning
The main plug shall be the main disconnect device and shall remain operable at all
times.
Never let anyone push objects into holes and ventilation slots.
Do not expose this product to dripping or splashing or place any objects lled
with liquids on or near the product.
Do not place a naked ame source such as lighted candles on or near this product.
Do not attempt to repair this product yourself; always get a qualied service agent
to carry out adjustments or repairs.
Consult the dealer or an experienced radio / TV technician for help. In accordance
with FCC requirements, changes or modications not expressly approved by
manufacturer could void the user’s authority to operate this product.
4
Components / Front View
Overview
Components
i View Classic unit
Power Supply Unit – US, EU, UK Plugs available
Remote Control
4 Cell Rechargeable Battery – Not included in the package.
(Must be purchased separately)
Desk Mount Clip (not seen in picture) – Not included in the
package.. (Must be purchased separately)
Securing Cable (not seen in picture) – Not included in the
package.. (Must be purchased separately)
Landscape/Portrait positioning screwdriver
Landscape/Portrait positioning screw
User Manual
1
1. IR receiver
5
Side A / Sidw B
Side A
Setting buttons
Left In menu mode, this function is used for moving left through the various
options. In playback mode you can go to the previous content in the playlist.
(Note: it is only operational for content copied from USB or SD Card, not for
content downloaded from i-Display Content Management System).
Right In menu mode, this function is used for moving right through the various
options. In playback mode you can go to the next content in the playlist.
(Note: it is only operational for content copied from USB or SD Card, not for
content downloaded from i-Display Content Management System).
Up In menu mode, this button is used for moving left. In playback mode, it is
used to increase the volume if current content being played is a movie.
Down In menu mode, this button is used for moving right. In playback mode, it
is used to decrease the volume if current content being played is a movie.
Misc In menu mode, this function is used for the same function as the OSD
button on the remote control (as explained in Remote Control section). In
playback mode, it is not operational.
OK In playback mode:
Short press – Used for making changes between
(i) Repeat selected movie (repeats the chosen le in endless loop).
(ii) Repeat all (repeats the entire playlist in endless loop).
Long Press (3 seconds) – Used to return to the menu page.
In menu mode:
Short press – Used for selecting various options.
Long press (3 seconds) - Used to return to the main menu (rst menu page).
6
Back
Side B
Silicon cover for slots
This reduces access to slots or prevents stealing of SD Card (if used).
To insert or remove an SD Card the Silicon cover needs to be
positioned as shown and can be easily opened by gently
lifting up and turning clockwise. A screw can be added
for extra security.
USB slot
This is used for connecting ash drives. Once the ash drive is connected, all its
content is automatically copied to the internal memory. To delete old content see
Playlist section.
SD card slot
Once an SD Card is inserted into the unit, the content on the SD Card will start to
play. In menu mode, the user will be able to either play content directly from the
SD Card or manually copy its content to the unit’s internal memory.
Important: SD Card is not included, it must be purchased separately.
Back
DC connector
Located at the back of the unit’s leg. Used to connect the power.
On/O button
Located on the back bottom section of the unit.
Red button indicates the unit is switched o. Green
button indicates the unit is switched on.
Important: It takes approx 10 seconds for the rst image
to appear once the unit is switched on
7
Back
Rechargeable battery slot
Used to house the rechargeable battery.
The rechargeable battery needs to be placed as shown in these images.
Removing the Rechargeable Battery
Placing the Rechargeable Battery
8
Back
Rotating screen to horizontal position
9
Quick Start
Operating Instructions
Quick Start
Turning On
Plug into electricity or insert fully charged battery.
Display will automatically load movie and play. (If the unit does not play a movie
automatically, press the power button at the back of the display. RED light
indicates standby mode and GREEN light indicates the unit is switched ON.)
Playing other movies / change content
Connect a USB stick to the unit.
Content from the USB stick will automatically be copied to the unit’s internal
memory.
Once the content has copied successfully, the new content will start playing
automatically.
Remove the USB from the unit.
Important: If you no longer require the old content to be played, you will need to
delete the old content (to explain how this is done see Playlist section).
Playing content from SD Card
Insert an SD Card to the unit.
The unit will play the content of the SD Card automatically.
Video
Recommended Video Resolution:
Landscape
Format: AVI
Codec: XVID
Audio code: MP3: layer 2/3; PCM: LPCM/IMA-ADPCM/MS-ADPCM/U-LAW
Resolution: 1920x1080
Portrait
Format: AVI
Codec: XVID
Audio code: MP3: layer 2/3; PCM: LPCM/IMA-ADPCM/MS-ADPCM/U-LAW
Resolution: 1080x1920
Video needs to be rotated anti-clockwise by 90 degrees for portrait movie playing
10
Table des matières
Autres manuels i Display Moniteur
