HySecurity Nice 3501 Manuel utilisateur
Residential | Commercial | Industrial | Anti-Ram | Parking
800-321-9947 •253-867-3700 • www.hysecurity.com
3501 Swing
CHBOX35:
ACTUATOR
MOTOR
CHASSIS
ABOX35: ARTICULATING ACTUATOR
Vehicular swing gate articulating actuator/motor
MX4754 REV. B ©2019
Installation Manual
3501 Actuator
INSTALLATION REFERENCE MANUAL
2www.hysecurity.com • 800-321-9947 MX4754 Rev. B ©2019
TABLE OF CONTENTS
LIST OF INSTRUCTIONS
INSTRUCTION 1: DETERMINE LOCATION OF MOUNTING POST ..................... 5
INSTRUCTION 2: DETERMINE HEIGHT OF MOUNTING POST ........................... 6
INSTRUCTION 3: WELD MOUNTING BRACKET TO POST ................................... 7
INSTRUCTION 4: MOUNT CHASSIS TO POST ...................................................... 8
INSTRUCTION 5: MOUNT PRIMARY ARM COLLAR TO DRIVE SHAFT................. 9
INSTRUCTION 6: ATTACH PRIMARY ARM TO ARM COLLAR ............................. 10
INSTRUCTION 7: ASSEMBLE ARM ASSEMBLY .....................................................11
INSTRUCTION 8: AFFIX GATE BRACKET TO ACTUATOR ARM ..........................13
INSTRUCTION 9: INSTALL GATE BRACKET TO GATE SUPPORT ........................15
INSTRUCTION 10: WIRE ACTUATOR CABLE TO CHASSIS TERMINAL STRIP ....16
INSTRUCTION 11: RUN ACTUATOR CABLE(S) TO CONTROL BOX ...................17
INSTRUCTION 12A: WIRE ACTUATOR CABLE TO CONTROL BOARD (LEFT) ...18
INSTRUCTION 12B: WIRE ACTUATOR CABLE TO CONTROL BOARD (RIGHT) .19
INSTRUCTION 12C: WIRE ACTUATOR CABLE TO CONTROL BOARD (DUAL) .. 20
INSTRUCTION 13: INSTALL CONTROL BOX AND APPLY POWER ................... 20
INSTRUCTION 14: SET OPEN AND CLOSE LIMIT COLLARS ................................. 21
INSTRUCTION 15: WELD OR BOLT GATE BRACKET TO GATE ......................... 22
INSTRUCTION 16: MANUALLY OPENING THE GATE ....................................... 23
SECTION 1: 3501 ACTUATOR OVERVIEW ..........................................................3
SECTION 2: INSTALLATION SAFETY ..................................................................4
SECTION 3: TOOLS NEEDED FOR INSTALLATION ............................................4
SECTION 4: 3501 ACTUATOR MECHANICAL INSTALLATION ...........................5
SECTION 5: ACTUATOR WIRING CONNECTIONS ...........................................16
5.1 CHASSIS WIRING .........................................................................................16
5.2 CONTROL BOARD WIRING...........................................................................18
SECTION 6: PART DRAWINGS..........................................................................24
SECTION 7: WARRANTY .................................................................................. 26
3501 Actuator
INSTALLATION REFERENCE MANUAL
3
MX4754 Rev. B ©2019 www.hysecurity.com • 800-321-9947
ABOX35 ACTUATOR:
CHBOX35
ACTUATOR
MOTOR
CHASSIS
ACTUATOR HARDWARE
KIT (P/N 1125-35)
ADJUSTABLE ALUMI-
NUM ARM INSERT (P/N
3500AAA)
GATE BRACKET,
(P/N 10025215)
3501 ACTUATOR PARTS IDENTIFICATION
PART# DESCRIPTION QTY
ABOX35 ACTUATOR, ARTICULATING ARM 1
CHBOX35 ACTUATOR CHASSIS 1
10025215 GATE BRACKET 1
1125-35 ACTUATOR BOLT KIT 1
3500AAA ARM INSERT, ADJUSTABLE, ALUMINUM 1
3501 ACTUATOR SPECIFICATIONS
DRIVE Electromechanical Motor Driven Articulated Arm
GATE LENGTH MAX. Up to 20 feet (6 m ) leaf
GATE WEIGHT MAX Up to 1000 lbs (453 kg)
OPEN/CLOSE TIME (TO 90°) 12 - 20 seconds (adjustable)
TEMPERATURE RATING -4º to 122º F (-20º to 50º C)
OPERATING VOLTAGE 12VDC
INPUT VOLTAGE 10 - 32VDC
ACTUATOR DIMENSIONS (WxHxD) 17.8” x 12” x 8.3”
USER CONTROLS 1050 control board
Congratulations on selecting a Nice swing gate actuator for your gate opener system. With proper selection,
system design, installation, and maintenance this actuator should provide years of reliable operation. This
manual covers ONLY the installation of the actuator.
IMPORTANT!
For control box installation, wiring, operation, programming, maintenance, and all safety information, refer
to the appropriate 1050 control box installation manual used for the system being installed.
SECTION 1: 3501 ACTUATOR OVERVIEW
ACTUATOR
HARNESS CABLE
3501 Actuator
INSTALLATION REFERENCE MANUAL
4www.hysecurity.com • 800-321-9947 MX4754 Rev. B ©2019
Below is a list of tools suggested for installation of the 3501 actuator:
• Welder (option for gate bracket)
• Drill and assorted bit sizes
• 1/2” and 3/8” wrench and/or nut driver
• Basic hand tools (screwdrivers, pliers, etc..)
• Bubble Level (for leveling actuator)
• Measuring tape (for locating post position)
• 1/8” and 5/32” hex keys (for set screws)
IMPORTANT!
• The gate operator installation is NOT a “do-it-yourself” project. Contract a qualied gate operator instal-
lation company to install this system to ensure a safe and reliable installation.
• It is the responsibility of the property owner to ensure the installer is qualied to carry out the installation
in a safe and professional manner.
• Consult local government agencies for up-to-date rules and regulations to satisfy licensing, codes or
regulations that regulate automated gate system design and installation.
• The gate for which the gate operator is intended to be used should itself be installed correctly so that it
is level and plumb and the gate opens easily and evenly.
• Note that Nice swing gate systems are not intended for installation on an incline.
SECTION 2: INSTALLATION SAFETY
SECTION 3: TOOLS NEEDED FOR INSTALLATION
WARNING!
READ ALL SAFETY INFORMATION IN THE CONTROL BOX INSTALLATION MANUAL WHEN
INSTALLING A SWING GATE SYSTEM!
BE AWARE OF ALL MOVING PARTS AND AVOID CLOSE PROXIMITY TO ANY PINCH POINTS.
3501 Actuator
INSTALLATION REFERENCE MANUAL
5
MX4754 Rev. B ©2019 www.hysecurity.com • 800-321-9947
OPTIMUM
DIMENSIONS
TABLE 1-1: MOUNTING POST LOCATION CHART
DETERMINE LOCATION OF MOUNTING POST
1
1. Determine the angle that the gate will travel to (A) in IMAGE 1-1.
2. Select the coordinates (B & C) as shown in the IMAGE 1-1. Distances of “B” are from the center of gate
hinge to the center of the mounting post. Longer gates should operate at slower speeds.
3. Refer to TABLE 1-1 for optimum dimensions.
SECTION 4: 35-1 ACTUATOR MECHANICAL INSTALLATION
E
C
B
D
A
A
Open
Degrees
B
Inches
C
Inches
D
Inches
E
Inches
Approx.
sec. to
open
90 10 31.2 46.3 40.6 15
90 10 30 47.1 42 16
92 15 30 42.1 34 15
97 13.5 25.5 46.3 46.8 17
97 15 25 45 47.1 16
100 20 25 40 43.7 13
107 20 20 42.4 53.5 17
110 25 20 37.4 50.6 13
116 25 15 39.3 58.4 16
117 20 15 44.3 50.3 20
3501 Actuator
INSTALLATION REFERENCE MANUAL
6www.hysecurity.com • 800-321-9947 MX4754 Rev. B ©2019
IMAGE 2-1: DETERMINING HEIGHT OF MOUNTING POST
2
• The top of the post should be 2” above the centerline of the
location where the gate attach bracket will be mounted to the
gate (IMAGE 2-1).
• The gate attach bracket should be mounted to a structural
member on the gate. DO NOT attach the bracket to pickets.
• The mounting post should be square to the gate in the closed
position and level for proper operation.
• Conduit should be considered at this time for cable routing
from the control box to the chassis assembly
DETERMINE HEIGHT OF MOUNTING POST
CENTERLINE
OF GATE
BRACKET
POSITION
TOP OF POST
2” ABOVE
BRACKET
CENTERLINE
GATE
STRUCTURAL
SUPPORT
MOUNTING
POST
2”
2”
NEVER WELD PARTS TO THE
GATE OR POSTS WHEN THE
CONTROL BOARD IS POWERED
TO AVOID IRREPAIRABLE DAM-
AGE TO THE CIRCUIT BOARD!
CAUTION!
The 3501 actuator chassis is designed for installation on top of a 4”x4” square post with 1/4” wall thickness
(not supplied).
3501 Actuator
INSTALLATION REFERENCE MANUAL
7
MX4754 Rev. B ©2019 www.hysecurity.com • 800-321-9947
IMAGE 3-2: WELD MOUNTING BRACKET TO POST
IMAGE 3-1: REMOVING COVER AND MOUNTING BRACKET FROM CHASSIS
3WELD THE MOUNTING BRACKET TO POST
POST
MOUNTING
BRACKET
1/2”-13x3/4” HEX BOLT (x4)
1/2” LOCK WASHER (x4)
LOOSEN BOTH MIDDLE
SCREWS (x2)
LIFT COVER
REMOVE BOTH END
SCREWS (x2)
1. To remove 3501 cover, loosen middle screws (x2), remove end screws (x2), and lift off cover.
1. Remove the mounting bracket from the CHBOX35 chassis bottom by removing the four bolts and lock
washers (IMAGE 3-1). Retain the hardware for later reassembly.
2. Weld the mounting bracket to the top of the mounting post (IMAGE 3-2):
• The bracket should be level and square to the post.
• Tack welds may be made from the top inside of the bracket and post.
• Bottom welds should be made for permanent rigidity.
MOUNTING
BRACKET
3501 Actuator
INSTALLATION REFERENCE MANUAL
8www.hysecurity.com • 800-321-9947 MX4754 Rev. B ©2019
MOUNT CHASSIS TO POST
4
Set the chassis on the mounting bracket as shown and secure using (4) 1/2”-13x3/4” hex bolts and lock
washers removed in the previous instruction.
IMAGE 4-1: MOUNTING CHASSIS TO MOUNTING BRACKET
IMAGE 4-2: PROPER ORIENTATION OF CHASSIS TO GATE
Chassis should be mounted to
plate so that the shaft for the arm
connection is on the opposite
side of mounting plate from the
gate when in the closed position.
DRIVE CHASSIS
MOUNTING
BRACKET
POST
MAIN DRIVE
SHAFT
SHAFT AT
OPPOSITE
SIDE FROM
CLOSED
GATE
3501 Actuator
INSTALLATION REFERENCE MANUAL
9
MX4754 Rev. B ©2019 www.hysecurity.com • 800-321-9947
MOUNT PRIMARY ARM COLLAR TO DRIVE SHAFT
5
IMAGE 5-1: MOUNTING PRIMARY ARM COLLAR TO MAIN DRIVE SHAFT
IMAGE 5-2: PRIMARY ARM COLLAR MOUNTED TO MAIN DRIVE SHAFT
1. Install the primary arm collar to the main drive shaft using the 1/4” key stock (IMAGE 5-1, Detail A).
2. The collar should be installed on the shaft as far up as possible (IMAGE 5-2). Use 5/32” hex key to
tighten set screw. Insert 1/2”-13x3” hex bolt into collar and afx with 1/2” hex nut (IMAGE 5-2) using
1/2” wrench.
3. Use retaining ring pliers to insert the retaining ring into groove on driveshaft (IMAGE 5-2, DETAIL).
PRIMARY
ARM
COLLAR
GROOVE ON
DRIVE SHAFT FOR
RETAINING RING
DETAIL
RETAINING RING
INSTALLED IN
DRIVE SHAFT
GROOVE
RETAINING RING
DRIVE SHAFT
RETAINING RING
MAIN DRIVE
SHAFT
MAIN
DRIVE
SHAFT
1/4” KEY STOCK
SET SCREW (5/32” HEX)
1/2”-13x3”
HEX BOLT
1/2” HEX NUT
DETAIL A
BOTTOM VIEW
BOTTOM VIEW
DRIVE SHAFT
RETAINING RING
NOTE: retaining
ring is included in
hardware kit 1125-
35.
3501 Actuator
INSTALLATION REFERENCE MANUAL
10 www.hysecurity.com • 800-321-9947 MX4754 Rev. B ©2019
Attach the primary arm to the collar using 1/2”-13x1-3/4” hex bolts (x2), 1/2” at washers (x4) and 1/2-
13 hex nuts (x2) per the images below:
6ATTACH PRIMARY ARM TO ARM COLLAR
IMAGE 6-1: INSTALL PRIMARY ARM TO COLLAR OF THE MAIN DRIVE SHAFT
(BOTTOM VIEW)
IMAGE 6-2: PRIMARY ARM INSTALLED TO COLLAR OF THE MAIN DRIVE SHAFT
(BOTTOM VIEW)
PRIMARY
ARM
ARM
COLLAR
EARS POINTING
TOWARD GATE
INSTALL USING
1/2”-13x1-3/4” HEX BOLT (x2)
1/2” WASHERS (x4) & 1/2”-13 HEX NUTS (x2)
NOTE: The two ears on the primary arm should point toward the direction of the gate.
BOLT
WASHER
NUT
WASHER
BOTTOM VIEW
BOTTOM VIEW
Table des matières
Autres manuels HySecurity ouvre-porte
HySecurity
HySecurity HydraSwing 40 Manuel utilisateur
HySecurity
HySecurity SlideSmart DC 15 Manuel
HySecurity
HySecurity SwingSmart DC 20 Manuel d'installation et d'exploitation
HySecurity
HySecurity SlideSmart DC Manuel utilisateur
HySecurity
HySecurity Nice 7251 Slide Instructions de montage
HySecurity
HySecurity SwingSmart DC Series Manuel utilisateur
HySecurity
HySecurity SlideSmart DC 15 Manuel
HySecurity
HySecurity SwingSmart DC Manuel utilisateur
HySecurity
HySecurity UL 325-2016 Manuel utilisateur
HySecurity
HySecurity HTG 320 Manuel de service
HySecurity
HySecurity HYNET SFP 4/1 Manuel utilisateur
HySecurity
HySecurity HydraSwing 40 Manuel utilisateur
HySecurity
HySecurity HVG 420 Manuel utilisateur
HySecurity
HySecurity StrongArmPark DC Manuel utilisateur
HySecurity
HySecurity SlideSmart DC 15 Manuel
HySecurity
HySecurity StrongArm 14F Manuel utilisateur
HySecurity
HySecurity SlideDriver II Manuel utilisateur
HySecurity
HySecurity HydraSwing 40 Twin Manuel utilisateur
HySecurity
HySecurity Nice 1500 Series Manuel d'installation et d'exploitation
HySecurity
HySecurity UL 325 Manuel utilisateur
